Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Club VII Bb/Eb.  (Read 613 times)

0 Members and 1 Guest are viewing this topic.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Club VII Bb/Eb.
« on: November 16, 2021, 06:45:01 PM »

I've just acquired this lovely instrument and I will be doing a full restoration over the winter.
For those of you who have seen Squeezy's advent calendar last year, this is based on an identical box and externally it will look pretty much the same as his when finished.
I also have a Club VI in C/F and this will follow on from it.
I mentioned in another thread I'd take some pictures of the levers and mechanism to show just how Hohner managed to pack so much in a tiny box.
However the bellows are completely shot and I'm going to have to learn how to make a set, or find somebody who could make me some.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Club VII Bb/Eb.
« Reply #1 on: November 17, 2021, 09:54:37 AM »

Before you decide to replace the bellows strip off all the old repairs.  If gussets are in a bad way (torn or perished) or if the cardboard on any corners has gone soft then I would get a new set.  Otherwise they should be repairable.  You need to remove the accumulation of old repairs and loose corners to see what you are dealing with.

You can get new bellows made to measure from Galassi, Marconi, or Carini.
« Last Edit: November 17, 2021, 09:56:51 AM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Club VII Bb/Eb.
« Reply #2 on: November 17, 2021, 10:43:14 AM »

Thanks Theo.
I've managed a few refurbs but I've not tackled anything  quite as bad as these.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: Club VII Bb/Eb.
« Reply #3 on: November 18, 2021, 08:19:38 AM »

I would look at two strategies ( given your interest in the Box )

1.  Measure the bellows o/d of actual bellows and o/d and length of fitting 'lip' and circulate it for comparisons with other models.  I appreciate the Club VII 'model' itself may have had a short run, but they may have used a stock size bellows that applies to other models ( including PA's )  You may be able to find - for far less than the cost/hassle of "new" bellows - a very good set of bellows on a suitable Box on Ebay De.

2.  I renovated a 'floppy' / soft /sunken bellowed set of bellows which I thought were 'scrap' on a 1930's Presswood.  The Box on the chest the bellows were on the lap!  The folds had all but gone, tape everywhere, some corners missing.  It was a big job....took the best part of a week probably of evenings but they came up ( arguably ) better than new.  The 'secret' if there was one seemed to be the 'paper' I picked up from one of the German Hohner shops.  I was a bit taken aback when it arrived as it was quite a bit thicker than the virtually tissue strength OEM but, when templated, cut, folded and glued it 'rescued' the integrity of the valleys and peaks.  I eased the corners off and opened then slightly with the thin edge of a wooden clothes peg and re-crimped them, replaced a small number with new ones and then re-taped the edges with a good quality PVC/cloth tape.

If you go so far as to strip the actual bellows paper from the card, as I did in that case, sorting the bellows corners and reinforcing any 'minor' failures in the actual card near the corners isn't that difficult because you have ready access. 

I would follow Theo's advice ( and mine ) and strip them - you aren't losing anything, if you think they are shot anyway ?  Get them down to 'nak-ed' and see where you go from there.  The original 'paper' on mine respond to a very 'lightly' dampened sponge and the use of a not too short thumb nail, whilst drying between sessions/sides so as not to get too damp.

If you want I can find the details of the paper.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Club VII Bb/Eb.
« Reply #4 on: November 18, 2021, 09:26:37 PM »

Thanks Nigel.
I've stripped all the electrician's tape and pulled off the corners that haven't already dropped off.
Then the old black edging tape peeled straight off very cleanly.
I've found it's fabric not paper and seems in pretty good nick.  However the corners of the cardboard are bad. Some soft, some crumbly and there are at least 10 metal corners missing. Some of the folds near the corners are weak and might benefit from some reinforcement. It will need a bit of glue to strengthen the weak work card edges, then I can decide whether to repair or replace.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal