Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Solvent-free/low odor/non-toxic adhesives for valves  (Read 3237 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Solvent-free/low odor/non-toxic adhesives for valves
« on: November 22, 2021, 02:32:47 AM »

There was some discussion on here from a while back about using UHU Solvent-free adhesive for valves.  I've experimented with many different adhesives for valves, and solvent-free is my preference due to a chemical odor sensitivity.  I ordered some of the UHU solvent-free glue from the UK and had it delivered to Canada, since that product is not available here.  The adhesive is a pleasure to use, and certainly works fine in attaching valves, however I always do a strength test the following day and was disappointed to find that the valves peeled off without a lot of effort.  I mean, I realize that no one is going to be pulling on the valves like that, but my concern is about longevity; I certainly don't want these valves falling off years down the road.  Has anyone used this glue and what was their experience?  I would like to avoid solvent-based glues with an odor at all costs.
« Last Edit: November 22, 2021, 03:22:56 PM by mselic »
Logged
C#/D player

Nigel.H

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 586
Re: UHU Solvent-free adhesive for valves
« Reply #1 on: November 22, 2021, 12:23:18 PM »

I bought some when Bostik Solvent Free was taken off the market.  The UHU - which was nothing like the Bostik product, still languishes in the drawer. It was pretty hopeless. 

I now use 3M Scotchweld Vinyl adhesive applied via a syringe and 'large' needle - easy to source via Amazon.  I too suffer from 'fume'/scent effects.

You get no fumes because you are using so little glue and although it can create a slight reaction (pucker) if over applied, using the syringe/needle allows a very fine line to be extruded, which deters that.  A 'sewing needle', in the hole of the syringe needle, means that once the syringe is filled it lasts for months - like the old 'polystyrene' cement / Airfix model making glue tubes of our childhood, with a pin in the nozzle.

Arguably a bit more expensive to set up with the 3M & syringes but a tube will last "years" in practice and very efficient.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: UHU Solvent-free adhesive for valves
« Reply #2 on: November 22, 2021, 01:39:53 PM »

I would also welcome anyone’s feedback on solvent-free/low odor/non-toxic adhesives they have successfully used for plastic and leather valves.
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #3 on: November 22, 2021, 03:24:04 PM »

I’ve changed the title of the thread to reflect the invitation for feedback/suggestions on solvent-free/low odor/non-toxic adhesives for valves.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #4 on: November 22, 2021, 03:27:26 PM »

If you can’t find a suitable adhesive you may need to invest in some basic fume extraction kit.  Perhaps you already have something like that for use when waxing?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

fc diato

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 146
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #5 on: November 22, 2021, 10:08:37 PM »

Hmmm...  I remembered someone recommending Lepage low odor contact cement (I remember b/c it was a rare Canadian reco; allowed me to refelt pallets).  I searched past posts and it turns out it was you - mselic, that is.  So, I guess you tried it and it wasn't good for valves? I'm curious to know why.
Logged
fc diato

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #6 on: November 22, 2021, 10:48:28 PM »

Carini list various glues for valves, but the only solvent free one appears to be . . . . . UHU !
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: UHU Solvent-free adhesive for valves
« Reply #7 on: November 23, 2021, 12:44:18 AM »

I would also welcome anyone’s feedback on solvent-free/low odor/non-toxic adhesives they have successfully used for plastic and leather valves.
I use hot pearl glue on leather valves. Bond is good ...but so far I have only had to glue leather valves on zinc reed plates. I wouldn't be inclined to try pulling them off the next day- with a brittle glue material bond is all or nothing.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #8 on: November 23, 2021, 02:38:20 AM »

Quote
I wouldn't be inclined to try pulling them off the next day- with a brittle glue material bond is all or nothing.

Pulling on them is only done when testing out a new glue...

Hmmm...  I remembered someone recommending Lepage low odor contact cement (I remember b/c it was a rare Canadian reco; allowed me to refelt pallets).  I searched past posts and it turns out it was you - mselic, that is.  So, I guess you tried it and it wasn't good for valves? I'm curious to know why.

The LePage low odour contact cement worked very well, but that was back when I was using valves with the holes punched out.  It seems that the extra gluing surface area around the rivet gave the glue a better overall grip (I just tested some that I had glued up a few years ago and they all required effort to pull off).  Nowadays I'm using valves without the holes and with less gluing surface area, and there is a noticeable difference in holding strength when using this same glue.  It works OK, but it has given me some concern over longevity.  I always aim for best practices and so am experimenting with other glues to see if there is one that works better.

If you can’t find a suitable adhesive you may need to invest in some basic fume extraction kit.  Perhaps you already have something like that for use when waxing?

Yes, I recently installed a fume extractor and a designated work station for waxing reeds.  The system seems to work well enough for wax, but I find the fumes from adhesives tend to linger longer.  I do also wear a vapor mask when waxing, but I'd rather not have to resort to doing all of that every time I re-valve reeds if possible.
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #9 on: November 28, 2021, 04:56:22 PM »

Mselic did contact me about this, and while I’d not encountered any issues with UHU solvent free, I thought I’d better go and (re)test the glue. I compared it with Evo-Stik contact adhesive, with both leather and plastic valves (one of each for each glue). I don’t get the valves coming off (I have left them for a couple of days…I forgot them) and the adhesion seems to be the same, all valves are firmly on and don’t pull off easily. I do clean the area to be glued with an abrasive rubber (the model railway rubber). My conclusion is that the UHU solvent free is ok for use…at least I will continue to use it anyway, as I cannot get the Bostik solvent free any longer. It’s less stringy than Impact and a blob of it doesn’t go off as rapidly as Impact. So for me it works well. I know others use Impact, which is a great glue. But I struggle with it personally.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #10 on: November 29, 2021, 01:11:05 AM »

Forgive me Roger, but what exactly do you mean by an “abrasive rubber”? Is that the same as a household eraser (for pencils)? We may have different terminology for the same things on this side of the pond…
Logged
C#/D player

Corinto

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 233
  • Spain/Brasil/Belgium
Logged
Carpe diem, C.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #12 on: November 29, 2021, 08:54:32 AM »

Hi mselic, as per the previous post, though I’ve got a Garryson block, I think the 600 grit. As in here…(it’s the UK Amazon…sorry), which is similar to the pico block. These little blocks are perfect for cleaning reed plates…and in fact the outer part of a reed tongue.
https://www.amazon.co.uk/s?k=garryson+blocks&crid=1ZB2RNMA2OZ7O&sprefix=Garryson%2Ctoys%2C157&ref=nb_sb_ss_fb_1_8_ts-doa-p

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #13 on: November 29, 2021, 09:06:07 AM »

Usually called “polishing block” in the jewellery trade were I get mine.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #14 on: November 29, 2021, 03:28:28 PM »

I’ve always scraped off the old glue, etc off with various tools, including small flat-head screwdrivers. I don’t glue new valves on until there are no traces left of the old glue. I would assume that amounts to the same thing as using an abrasive block of some kind.

The other thought I had was the plastic valve material, and if the same glue adhered differently to different valves.  I’m currently using the plain white plastic valves from Carini.
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #15 on: November 29, 2021, 04:56:50 PM »

Me too. Carini valves. The mildly abrasive block does also clean off any wax/grease, but I suspect you are already doing that. So I don't know why your valves pull off in the way you describe. There are lots of glue options to choose from. I use this one to increase my valving speed. Revalving a PA can be a long tedious job, so anything that enables me to work fast (i.e. pre gluing a row of valves and then sticking them on) is a help.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #16 on: November 29, 2021, 05:33:13 PM »

I’m also re-valving a lot of PAs, so I’m motivated by the same reasons as you!
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #17 on: December 01, 2021, 05:35:27 AM »

I've attached a photo of the UHU glue I'm using.  Is this the same one, Roger?  I just don't understand how we could be getting such different results using the same product and same materials. 

Here's a quick video of me testing out a valve 24 hours after it was attached with the glue.  Sure, it holds well enough to do its job within the instrument, but the fact that it comes off as easily as it does with a gentle tug doesn't inspire much confidence in longevity:

https://youtu.be/6OgrijqV8Rk
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Solvent-free/low odor/non-toxic adhesives for valves
« Reply #18 on: December 01, 2021, 07:40:02 AM »

I think the shell life of solver free glue is much shorter than the equivalent with solvent.  I once bought a few tubes of a diy shops own brand.  The first tube was fine, but after maybe 6 months the contents of the next tube was much less fluid and didn’t work well.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal