Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Reed block materials . . . ?  (Read 2870 times)

0 Members and 1 Guest are viewing this topic.

CAB

  • Mass Debater
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1147
    • Somerset Russets Village Band
Re: Reed block materials . . . ?
« Reply #20 on: December 14, 2021, 02:47:33 PM »

Colin Dipper told me to remove and put back the screws in my Wheatstone Linota in a 1,3,5,2,4,6 Rotation. And to tighten them to similar torque, as judged by my wrist. Same concept?

I've always adopted the same principle with concertinas but assumed it was more about not distorting the ends rather than any acoustic effect.
Logged
Pas de lieu Rhone que nous

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Reed block materials . . . ?
« Reply #21 on: December 14, 2021, 03:09:02 PM »

Colin Dipper told me to remove and put back the screws in my Wheatstone Linota in a 1,3,5,2,4,6 Rotation. And to tighten them to similar torque, as judged by my wrist. Same concept?

I've always adopted the same principle with concertinas but assumed it was more about not distorting the ends rather than any acoustic effect.
Yep, that's the reason, same as when (old people alert) you took the head of your car to decoke it there was a strict retightening order to prevent distortion.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Reed block materials . . . ?
« Reply #22 on: December 14, 2021, 05:32:45 PM »

Another tip for any gasketed joint  is avoid overtightening. Stop when you get a good seal.
You can't use a torque wrench on it, so good judgement is essential.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Reed block materials . . . ?
« Reply #23 on: December 14, 2021, 11:20:03 PM »

Colin Dipper told me to remove and put back the screws in my Wheatstone Linota in a 1,3,5,2,4,6 Rotation. And to tighten them to similar torque, as judged by my wrist. Same concept?

I've always adopted the same principle with concertinas but assumed it was more about not distorting the ends rather than any acoustic effect.
Yep, that's the reason, same as when (old people alert) you took the head of your car to decoke it there was a strict retightening order to prevent distortion.


Or wheel nuts, for people who remember the days when you had to change a wheel on a car...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Reed block materials . . . ?
« Reply #24 on: December 15, 2021, 09:53:18 AM »

A few years ago I attended a melodeon-fettling workshop with the Bernard Loffet.  He was very insistent that when removing reed blocks the retaining screws should turned a precise number of times, and on re-fitting them tightened by exactly the same amount, to maintain the same pressure.

Consistent pressure and not too tight sounds good, and specifically to Bernard Loffet at least one of his 3 voice models has its L reeds in a central Reed block that sits ‘floating’ on top of the wooden register slide. it’s a very small sweet spot of pressure to be able to operate the slide smoothly, yet not have any air leaks or other oddities occur.
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal