Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Declubbing Bass - Reed Modification  (Read 1166 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Declubbing Bass - Reed Modification
« on: January 14, 2022, 11:38:31 AM »

I just thought I would post this as it might be of interest.

I am just finishing off my "experimental" box (the one I don't mind opening up on a regular basis).  It is made from from Club Modell 1 (23 key) bits but I have modified frames, changed to gaskets etc. and have recently been de-clubbing (treble and chords). The final mod was changing the bass. Its a C/F club so I had to move the bass from Eb/Bb to Bb/Bb.  I had left it until last as it struck me as the most "tenuous" in terms of mod.  The Bb octave reeds are not brass weighted and while they both have reed thickness at the tip I doubted that it was anywhere near enough.

Anyway to cut a long story short.  The Eb2 to Bb2 went OK with filing the tip mass (hit the required frequency with adequate residual thickness) but on the Eb3 there was no chance which became obvious almost immediately.  So my solution was as follows.... 

Below is a video of the modified working reed.  In the video the reed runs at its new true frequency 233 Hz both ways and then repeats in slowmo to show performance.  It's interesting as you can see the reeds start. Both push and pull are shown after each other for comparison (both Bb3).

I think the video should work if you click through to flikr and then start.

Reed Test - foreshortened reed (normal/slow motion) by John Burks, on Flickr

To explain .... I had shortened brass reeds before bit not steel.  To make sure that I gave it the best chance I thinned the tip and then shortened creating a new leading edge with brass strip and then backfilling the reed frame to give the depth (this also provides the main strip bond).  I used UV glue/weld to create the new reed plate depth and used the brass strip to help cut the new edge.  The glue hypodermic dispensers are best for weld placement.

In tests I cant tell the difference between a pure reed and the modified.  Not the best solution but it works for me.  The box is all Hohner H reeds which I really like so that is good .... albeit one is a bit shorter! Looking back I wish I had shortened the Bb2 to keep thickness depth of sound.

I just thought I would share.  This is a great site and it has taught me a lot  (:)

I will post some photos later.

Mod:  See this video link and below.  Its a bit better on Youtube >>> https://www.youtube.com/watch?v=5YO2z7l52NY
« Last Edit: January 14, 2022, 04:52:16 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Declubbing Bass - Reed Modification
« Reply #1 on: January 14, 2022, 04:41:22 PM »

Not sure if this will help anybody but here are a few photographs. 

In my opinion this is a perfectly valid way to modify a reed to change frequencies.  Ok its non reversible but then so is thinning.  Worth trying if you are stuck.

Link to a better Youtube video:-  https://www.youtube.com/watch?v=5YO2z7l52NY&t=2s

This video shows the modified Bb3 reed working in the reed block (push) alongside its companion unmodified Bb3 reed on the inside of the block (pull).  They alternate.  You can compare the frequency and response.  The slowmo shows the reed start quite well.

Starting Notes by John Burks, on Flickr

My notes to make sure I know where I am headed.


Reed reduced by John Burks, on Flickr

The reduced reed.  I thickness filed part way to reduce the loaded tip of the reed to get the thickness right which took me to about 275 Hz and then I took the reed end down with a rotary emery wheel to 230 Hz leaving a bit of leeway for tuning.

Brass strip in place by John Burks, on Flickr

Brass strip glued to reed plate.  I used Hohner valve glue to hold it in place.

UV cure by John Burks, on Flickr

UV curing.

UV fill by John Burks, on Flickr

UV glue/weld in place. I used the needle type applicator and 5 sec cure.  Its this mass that actually fully bonds the brass strip.

Trimming by John Burks, on Flickr

I then shaped the UV glue with a scalpel until the fit was good. You can use the brass strip to help get a clean square end to the aperture.  You just run along it.  If you do this just after curing you can slice the UV treated glue/weld before it get really hard.. I did a second 30 sec UV cure after I was happy with the fit.

Finished reed by John Burks, on Flickr

The finished reed.

Completed Mod Reverse by John Burks, on Flickr

Finished reed reverse.

Valved by John Burks, on Flickr

Valves in place.  The soft leather valve suit as it seals the brass strip.  Final tune to 233 Hz.


Hope the above is of interest  :D

« Last Edit: January 14, 2022, 04:53:01 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Andrew Kennedy

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 184
    • About Sword Dancing
Re: Declubbing Bass - Reed Modification
« Reply #2 on: January 14, 2022, 08:36:35 PM »

1) This is impressive, and far beyond my level of competence.  A job well done.
2) But why? Why do people keep buying Clubs and butchering them? It's a great system if you can be bothered to take a little time to learn it, and it really is a little time if you can play already.  They made these boxes for a reason, and it hasn't gone away. Why not butcher (select Italian box of choice)?

All right, yes, supply and demand.  I just live for the day when more people will demand Club boxes (hurry up, I'm already sixty).
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Declubbing Bass - Reed Modification
« Reply #3 on: January 14, 2022, 10:07:44 PM »

1) This is impressive, and far beyond my level of competence.  A job well done.
2) But why? Why do people keep buying Clubs and butchering them? It's a great system if you can be bothered to take a little time to learn it, and it really is a little time if you can play already.  They made these boxes for a reason, and it hasn't gone away. Why not butcher (select Italian box of choice)?

All right, yes, supply and demand.  I just live for the day when more people will demand Club boxes (hurry up, I'm already sixty).

1) Ta

2) I suppose it comes down to personal preference  (:). I also think that it’s because there is little or no training material or inspirational material (at least for me) out there that drives you to learn the club system. I am new to melodeon playing and when you look around how do you learn with a C/F club box? …. Believe me I have tried. Lots of helpful D/G material but little else. Thankfully there is some two row international C/F videos (thank you for those videos).

That said …. You are right …. these boxes should be celebrated as they sound wonderful (albeit adjusted).  ;)
« Last Edit: January 14, 2022, 10:14:08 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Declubbing Bass - Reed Modification
« Reply #4 on: January 15, 2022, 08:02:06 AM »

Another possibility would be to get a suitable small Bb reed from an old PA (old PAs, at least in the UK, are easily obtainable either free or for a few quid).

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Declubbing Bass - Reed Modification
« Reply #5 on: January 15, 2022, 10:16:40 AM »

1) This is impressive, and far beyond my level of competence.  A job well done.
2) But why? Why do people keep buying Clubs and butchering them? It's a great system if you can be bothered to take a little time to learn it, and it really is a little time if you can play already.  They made these boxes for a reason, and it hasn't gone away. Why not butcher (select Italian box of choice)?

All right, yes, supply and demand.  I just live for the day when more people will demand Club boxes (hurry up, I'm already sixty).

1) Ta

2) I suppose it comes down to personal preference  (:). I also think that it’s because there is little or no training material or inspirational material (at least for me) out there that drives you to learn the club system. I am new to melodeon playing and when you look around how do you learn with a C/F club box? …. Believe me I have tried. Lots of helpful D/G material but little else. Thankfully there is some two row international C/F videos (thank you for those videos).

That said …. You are right …. these boxes should be celebrated as they sound wonderful (albeit adjusted).  ;)
I don't get the "No learning material"
The modern tutorial material for new English C/F players is the D/G material.
You just play your C/F melodeon as a low pitch D/G.
New players of 2 row boxes begin by learning simple tunes on the row - this is what all the D/G manuals lead you through.
I know of C/F players who having learnt on the D/G use ABC to transpose music they want to play on the C/F into D or G to make the reading of it easier for them.
As for the Club buttons - just don't use them until you get to the stage that you want to explore what you can do with them.

Historically, before the D/G became popular all British manuals were based on C, C/F and C/C# boxes. Some time ago I acquired a one row originally sold by Campbell's of Trongate Glasgow. It came with original carrying case and a manual. The music was in C. The box was in F.
Logged

Chris Rayner

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 467
Re: Declubbing Bass - Reed Modification
« Reply #6 on: January 15, 2022, 04:11:11 PM »

Surely there is more to the differences between Club instruments and the standard English D/G.  The Gleichton and accidentals row quite apart from the basses.
Logged
Elderly amateur musician hoping to stave off dementia by learning to play the melodeon.  Main instrument a Tommy, also D/G and G/C pokerworks,  a single row 2 stop Hohner, and a new addition to the free reedery, a rather splendid Paolo Soprani four voice 120 bass c-system chromatic button accordion.  Very shiny, very loud, and about the same size and weight as a small car.  Now I’ve traded me Benny with (ahem) a cash adjustment, to a three voice 60 bass Castagnari K3.

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Declubbing Bass - Reed Modification
« Reply #7 on: January 15, 2022, 04:16:58 PM »

There are a couple of Club system tutors in German available for download as PDFs on the "melnet" page of my web site:
https://treewind.co.uk/melnet/
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Declubbing Bass - Reed Modification
« Reply #8 on: January 15, 2022, 05:37:27 PM »

About reed modification: I did something a bit similar to what John describes (but without brass strip) a few years ago and agree this is a valid and useful - if unconventional - technique.

See the last post in this thread http://forum.melodeon.net/index.php/topic,20752.msg282736.html#msg282736

Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Declubbing Bass - Reed Modification
« Reply #9 on: January 15, 2022, 05:51:03 PM »

Thanks for all the responses!  The thing I like about this site is that it gets me thinking.

The good news is that I also have another pretty much unmodified Hohner Modell 1.

I should probably have mentioned that the box I'm working on is already a bit of a mix.  It's made of Hohner Modell 1 Picoletta ends/mechanics (which came in bits) with Erica bellows.  I had to make frames etc.  It's fully stripped of wax, neoprene gasketed and refinished.  Its comes apart very easily. It is on Club reed blocks though. Its perfect for me as I can whip a reed out, adjust and replace it in minutes.  I did this to allow for easy tuning.  Hence not being too worried about altering. It's is pretty heavily modified already!

I am pretty new to melodeons but I really do like the rich sound you can get/develop.  I like drones and chords particularly hence the Bb/Bb mod which I had resisted for a while.  I also want to get this box just right for me so want to continue to experiment.  I am also a great believer in knowing an instrument like the back of you hand.  The wonderful thing is that such a simple construction can be easily worked on and be made to work so well.  I am not an expert but the early Hohners do have a really rich sound.  I really like the H reeds. The key mechanisms are also really responsive.  Its about developing the perfect sound balance for me. 

I'm rambling ........  :-\

I do intend to raid a PA for reed stock now I am comfortable filing and modifying reeds (I will need them).   I want H reeds though so my question is which models have them?  Is it an age thing? Do the Student PA's have H reeds for instance?

Thanks for the view on club and declub and resource suggestions. It is very much appreciated.
« Last Edit: January 15, 2022, 06:02:19 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Declubbing Bass - Reed Modification
« Reply #10 on: January 15, 2022, 06:00:31 PM »

About reed modification: I did something a bit similar to what John describes (but without brass strip) a few years ago and agree this is a valid and useful - if unconventional - technique.

See the last post in this thread http://forum.melodeon.net/index.php/topic,20752.msg282736.html#msg282736

Just taken a look.  That's is a really clean finish  :D

I will give metal filler a go  (:)

Thanks

John
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Declubbing Bass - Reed Modification
« Reply #11 on: January 15, 2022, 08:41:14 PM »

"Do the Student PA's have H reeds for instance?"

The old white wooden bodied Students which I've scrapped all had steel reeds on zinc H plates.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal