Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Dino Baffetti Black Pearl 3 - Sticking Key  (Read 1201 times)

0 Members and 1 Guest are viewing this topic.

JD

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 235
Dino Baffetti Black Pearl 3 - Sticking Key
« on: February 08, 2022, 01:10:45 PM »

A friend has asked me to look at his BP3 which has a sticking key. The box is fairly new.

I have run a three thou feeler gauge down both sides of the key to check for anything stuck in the slot without finding anything. I have also tried to push the key gently sideways. It has a similar amount of play as the non-sticking keys either side.

My next thought was to use a small drill chuck to twist the axle to see if the key was sticking to that. When I took the cap off the underside of the box I found only about 1mm of axle protruding, not quite enough to grab with the chuck. Is this normal for these boxes? Is this where I hand the box back to be sent to a repairer?
Logged

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #1 on: February 08, 2022, 01:35:40 PM »

If the box is fairly new I would suggest that it may be still under warranty and advise don't touch it if this is the case.
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

JD

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 235
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #2 on: February 08, 2022, 02:20:14 PM »

If only the receipt could be found... :-[
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #3 on: February 08, 2022, 02:39:42 PM »

Usually when this happens it’s because the hole in the lever is too tight a fit on the axle rod.  This can be a result of the wood moving due to changes in humidity, or dirt or corrosion on the axle rod.  Whatever the cause twisting the axle rod may help in the short term. The long term fix is to withdraw the axle rod completely and clean it and very carefully clean the hole in the key lever.  This must be done with great delicacy because if the hole is enlarged even slightly more than necessary the result will be a key with a lot of sideways movement which much harder to put right.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #4 on: February 08, 2022, 04:32:22 PM »

I had this problem with an older box with a wooden linkage. Eventually [the experienced fettler] resorted to passing a heating current through the rod, using a car battery.

Touch wood (plenty of the stuff involved), no reoccurrence of the problem since (four years).

You may not need the receipt. It may be worth checking with the supplier.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Tufty

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 855
  • Dino Bincis etc
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #5 on: February 08, 2022, 05:32:09 PM »

What Theo said! I had this issue with both the DBs I have owned.
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #6 on: February 08, 2022, 06:36:21 PM »

Further to Theo's comments about dirt / corrosion on the axle rod . . . . sticking keys seems to be a very common complaint with these,  and the couple that I have had to deal with have both had corrosion on the axle.

Rather than clean and refit the existing axle I like to replace it with a polished stainless axle which is much better able to deal with a bit of humidity and will be easier to extract in future if needed.
I appreciate not everyone will have something suitable to hand, but IIRC the axle is 2mm dia in which case a length of stainless TIG welding rod makes a good material that you might be able to scavenge
from a handy welder / fabricator.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #7 on: February 08, 2022, 06:45:14 PM »

Personally I would not use a car battery on a Dino. For those who have never tried it, it can have spectacular results if you get it wrong… (:)

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #8 on: February 08, 2022, 08:23:33 PM »

Personally I would not use a car battery on a Dino. For those who have never tried it, it can have spectacular results if you get it wrong… (:)

Fair enough. Kids, don't try this at home. As I said, it wasn't me wot did it, but an experienced and accomplished fettler.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #9 on: February 08, 2022, 11:58:03 PM »

I got my old Dino Baffetti out the other day for the first time in months and found what appeared to be a sticking key. Upon investigation and removing the grill, it turned out not to be that at all, but the bottom edge of a pallet felt on the outside row just barely touching the top edge of a pallet on the inside row, just enough to prevent the button returning to rest and the pallet closing.  Worth a look in case you've not checked that possibility; and much easier to fix if it turns out to be that....
Logged
Tuner/repairer, now retired.

JD

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 235
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #10 on: February 09, 2022, 11:52:48 AM »

Thanks for all the suggestions. There is about 2mm of clearance between the pallets so no chance of snagging there (I have seen that problem on Club II boxes). The main problem for me is that the end of the axle only protrudes from the case by about 1mm and that includes the sloping bit where it was chopped off. On older BP3 models the end of the axle rod is bent into a loop so it can easily be gripped by pliers.

My own BP3 (vintage 1994) has no sticking keys. If it did I would feel fairly confident to dismantle it to find the problem. As it is, the box in question isn't mine and I don't have the tools to get the axle rod out. A trip to an expert beckons.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #11 on: February 09, 2022, 11:55:26 AM »

JD

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 235
Re: Dino Baffetti Black Pearl 3 - Sticking Key
« Reply #12 on: February 09, 2022, 07:11:50 PM »

That video makes sense of an old post about replacing axles. The post mentioned using a drift to help remove the axle but that only makes sense if both ends of the axle are accessible. Neither of the BP3s in my house at the moment have that access hole on the top of the instrument. Is the hole shown in the video a standard fitting of wooden-bodied Baffettis?

Asking from idle curiosity as I recognise when I can do more harm than good.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal