Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Beat tuning across Octaves  (Read 1387 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Beat tuning across Octaves
« on: March 07, 2022, 01:20:58 PM »

Wondered if anybody can help/advise?   I am currently tuning an old Anglo concertina.  Long plates with brass reeds. It is a version that works in octaves i.e. each note sounds two reeds an octave apart e.g C4/C5, B3/B4 etc.

I have just started tuning to A440 and have noticed that having got reed pairs at there respective frequencies (+-3 cents) some notes are sounding at a distinct beat rate.  A pretty wonderful sound.  Has anybody got any experience in setting up beat rates across octaves?

Having analyzed the reed frequencies the beat rate seems to derive from the higher member of the octave.

A typical set of reeds are as follows:

C4 running at 262.1 Hz
C5 running at 522.2 Hz

gives me about 2 beats per second.  So I'm assuming 262x2 = 524 against C5 actual at 522 Hz.... hence the beat rate?

Apologies in advance for talking concertinas here but I would like to try to set up this up as best I can. Would appreciate any advice.

Ta

John
« Last Edit: March 07, 2022, 01:28:48 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Beat tuning across Octaves
« Reply #1 on: March 07, 2022, 02:07:25 PM »

If you are accepting a pitch within +/- 3 cents you could have as much as 6 cents difference between two reeds.  If you want either no beats, or a consisten best rate you need to be working to closer tolerances.

If you have two frequencies sounding together then the beat rate is just the difference.  So for example if you have 522Hz and 524Hz sounding together the beat rate is 2 Hz, or 2 beats per second.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Beat tuning across Octaves
« Reply #2 on: March 07, 2022, 03:05:06 PM »

Hi Theo, Thanks for the reply.  Agreed re the tolerances.  I need to improve quality control  (:)

I've just been out for some emery boards.  I find these useful with these brass reeds.  They should sort it.

I usually try to get to well below +-1 cent deviation but was struggling this morning with these long plates and what appears to be a softer brass.  I am now going to take the tolerances down and then fine tune beats by reference to Hz and ear.  Given the two different frequencies I am finding the side by side cents readouts I usually use for dedic confusing  ::)
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Beat tuning across Octaves
« Reply #3 on: March 07, 2022, 04:30:07 PM »

Fibreglass pen is a very nice gentle tool for tuning brass reeds. It leaves a nice smooth finish.  Just be careful of the dust, it's not nice if you inhale it.

https://regton.com/fibreglass-pen.html
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Beat tuning across Octaves
« Reply #4 on: March 07, 2022, 05:10:44 PM »

I admit this query isn't to do with melodeons, but I wondered if anyone might know - I use a tuning application on my mobile phone called Soundcorset that seems to measure down to plus or minus one cent.  However with a guitar string, if you pluck the halfway harmonic on a low wound string, it seems to show the harmonic being about 3 cents flat on the octave, unexpectedly.  How accurate are these aps? Or is it the string that's the problem?
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Beat tuning across Octaves
« Reply #5 on: March 07, 2022, 05:31:17 PM »

"How accurate are these aps? Or is it the string that's the problem?"

My banjo was like that, and it turned out to be that the action wasn't right.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Beat tuning across Octaves
« Reply #6 on: March 07, 2022, 06:55:04 PM »

with a guitar string, if you pluck the halfway harmonic on a low wound string, it seems to show the harmonic being about 3 cents flat on the octave, unexpectedly.  How accurate are these aps? Or is it the string that's the problem?

It's the string, but there's nothing wrong with it. Surprisingly, harmonics on many instruments are not perfectly in tune. The reason, I believe, is an end effect where the "end" of the string, for frequency calculating purposes, is slightly beyond the physical end of the string. It's the same amount of extension whatever pitch you are trying to sound, so if the end effect adds 1% to the total length of the string, when you play a harmonic where the vibrating string is two equal lengths, the same end effect is now adding 2% to the effective length.
Pianos have hugely out of tune harmonics, especially at the lower end of the instrument, which is why they sound like nothing else and also one reason why they are very hard to tune.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Beat tuning across Octaves
« Reply #7 on: March 07, 2022, 09:48:55 PM »

with a guitar string, if you pluck the halfway harmonic on a low wound string, it seems to show the harmonic being about 3 cents flat on the octave, unexpectedly.  How accurate are these aps? Or is it the string that's the problem?

It's the string, but there's nothing wrong with it. Surprisingly, harmonics on many instruments are not perfectly in tune. The reason, I believe, is an end effect where the "end" of the string, for frequency calculating purposes, is slightly beyond the physical end of the string. It's the same amount of extension whatever pitch you are trying to sound, so if the end effect adds 1% to the total length of the string, when you play a harmonic where the vibrating string is two equal lengths, the same end effect is now adding 2% to the effective length.

Really interesting. Not thought about that before but it stands to reason. There will be a bending moment at each end.  Re a guitar it will be at the nut and bridge. Thinking about it when you hit a first harmonic by touching the string at the twelfth fret I.e with two equal half string lengths. the deflection will/may be altered and the oscillation frequency will double. So bending moment will at least double over time. Same with higher harmonics.

A tuning nightmare!    (:)

Heading off to dig out guitar…..

John
« Last Edit: March 07, 2022, 09:51:38 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Beat tuning across Octaves
« Reply #8 on: March 07, 2022, 09:51:01 PM »

 
Fibreglass pen is a very nice gentle tool for tuning brass reeds. It leaves a nice smooth finish.  Just be careful of the dust, it's not nice if you inhale it.

https://regton.com/fibreglass-pen.html

Hi Theo,  thanks. Delivery expected Wednesday  (:). Tuning coming along.
Thanks again

John
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Beat tuning across Octaves
« Reply #9 on: March 08, 2022, 12:14:35 AM »

Anahata, the effect is not really noticeable on the top strings.  This could be because the extension to which you refer could be greater for thicker strings?  The only thing I was musing about with your explanation is whether there's an 'end' effect at the mid-point - I would doubt it, so wouldn't that mean that each half of the string on the harmonic is only extended by half the amount?  Hmm.  My hunch was that the effect might have something to do with round-wound strings having different characteristics to plain strings, as evidenced by the raked angle of guitar saddles, but there seem to be anomalies with that idea too.

Oh, fortunate free-reed tuning experts, you only have one note to get right!  Which is perhaps why boxes are usually much more in tune than guitar accompanists!
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Beat tuning across Octaves
« Reply #10 on: March 08, 2022, 07:28:55 PM »

About string harmonics, here are a couple of pages from the book 'Piano Servicing Tuning & Rebuilding' by Arthur A. Reblitz that may be of interest.

(he uses the word 'partial' to describe a real-word harmonic that is not an exact multiple of the fundamental)
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Beat tuning across Octaves
« Reply #11 on: March 08, 2022, 07:30:19 PM »

... second page ...
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Beat tuning across Octaves
« Reply #12 on: March 08, 2022, 08:33:33 PM »

[[ADMIN]]

Please have some consideration for John Burks who is looking for help with tuning octave reeds and not strings.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Beat tuning across Octaves
« Reply #13 on: March 08, 2022, 08:59:22 PM »

Not sure if this makes sense, but I would inhibit each lower reed and tune its higher reed to nominal absolute frequency of the particular note, doing this for each reed pair (using whatever technique you prefer, frequency counter or tune to a tone, etc.). When you're happy with the higher reeds tune each lower reed  by ear to the exact (i.e.,beat free) lower octave. Next detune each lower reed to give the  beat density you  want. Forget about what the theory says about what this frequency should be. Trust your ear.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Chris Brimley

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2038
Re: Beat tuning across Octaves
« Reply #14 on: March 09, 2022, 09:40:55 AM »

Indeed, Theo, and apols for drifting.  I commented originally partly because I wasn't sure from my experience whether tuner aps were always accurate, but the consensus seems to be they are.  We've had an interesting discussion about something else, but I'll drop it there!
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Beat tuning across Octaves
« Reply #15 on: March 11, 2022, 11:49:16 AM »

Firstly many thanks for all the posts.  This is a great forum. A great resource and it helps me keep focussed.

Not sure if this makes sense, but I would inhibit each lower reed and tune its higher reed to nominal absolute frequency of the particular note, doing this for each reed pair (using whatever technique you prefer, frequency counter or tune to a tone, etc.). When you're happy with the higher reeds tune each lower reed  by ear to the exact (i.e.,beat free) lower octave. Next detune each lower reed to give the  beat density you  want. Forget about what the theory says about what this frequency should be. Trust your ear.

Made perfect sense and really helped get my mind round it! Thanks.  (:) Really good advice …… I had to modify the approach slightly though as I went through it.
I set all the reeds to perfect A440 pitch (all well within 1cent) which took me quite a while as the range was C2 to F#6.  (Thanks Theo btw for recommending the fibreglass pen. It worked a treat and the polished surfaces are great.)
I then tried dropping one of the lower reeds by establishing an offset and testing by ear but when I analysed the resultant pair the beat was there but I found the note was flattened slightly more than I expected and the rate was high. The lower reed of the pair dominates in terms of volume and adjusting the Hz on the lower frequency seemed to double the beats. So, I altered the approach and tuned all lower reeds to perfect pitch and then for each reed pair noted the lower reed frequency doubled it and then added 3Hz. This gave me the target for the higher reed. I then tuned it by reference to frequency to give the perfect 3Hz offset. This worked better for me and allowed me to keep track of what I was doing! (:)
This worked a treat. The offset needs to be on the higher pitch.
On this basis I have tuned the first row (all to 3Hz offset) and I actually have a sound that is rich.  The beat rate is consistent across the row and louder than I would expect.  This is what I hoped for. I will now spend some time refining by ear.

This concertina was owned and played by my great grandmother and to hear it work again after many many years is pretty amazing..

Thanks for the help.

What it has also made me realise is that you can beat tune over octaves or multiples. So I might try to tune bass octaves.

Will post an illustrative video later.

John
« Last Edit: March 11, 2022, 05:28:42 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Beat tuning across Octaves
« Reply #16 on: March 11, 2022, 02:43:29 PM »

Further to the previous post here is a link to a video that shows the D3/D4 reeds beating.  The lower reed takes dominance under "Tuner" and it only registers D4 every so often.  You can hear and see the beat and amplitude though so all is good.  Apparently they are called "beats of mistuned consonances"  :o

The beat rate is applied to the higher frequency .......... f2=2f1+delta

where F2 is the higher frequency
F1 is the lower frequency
delta is the beat rate required in beats (Hz)

It also works over multiple octaves and you just increase the mutiple.

Just click on the video and it should launch flickr then just press play.  You will need sound on for the full effect  (:)

The tuning software take time to analyze the waveform and settle so hang on ....


Tuner - Octave D3D4 by John Burks, on Flickr



« Last Edit: March 11, 2022, 02:58:16 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal