Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Progress update: Meinhold Melodeon  (Read 404 times)

0 Members and 1 Guest are viewing this topic.

Thomas Barnatt

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Progress update: Meinhold Melodeon
« on: March 23, 2022, 01:48:37 PM »

Just a little update about what I've gotten done so far. I had to rebuild the Bass end, the old hide glue was really dried up and the whole thing fell apart. The panel, either shrunk or was just made that way, was too narrow to fit within the grooves of the frame so I added small strips of mahogany to each side then put the whole thing back together. I reinforced from the inside with strips of wood as can be seen in image. I repaired the basses/air box, had to add bits of wood for screws to grab because a couple were on the edge and not holding. I removed all hide glue from inside where pallets sat and after putting new leather on them installed them and cleaned up springs, it's ready to be put back on, they work really well.
I filed and sanded the grooves in the reed blocks that hold the reed plates so they can be put in and removed easily, they are still snug but you don't need pliers anymore to get them out!
I tried saving the three or four original cardboard pallets but they were beyond saving, just deteriorating as I cleaned old glue off. I made new ones of mahogany but they didn't stay flat. The new ones are quarter sawn white oak and have stayed flat for a couple of weeks. I put new leather on a week ago and they still are flat, so I am going to glue them to the wires. The round air holes are not directly over the oval holes for the extra voice reeds so the pallets are not perfectly vertical. I made a clear stiff plastic pallet and centered it over each location and marked the sides and one end with pencil so to insure the correct placement of the real ones, being evenly spaced over the air holes. I can now glue them to the wires. It took quite a bit of time to adjust all the wires so they pressed evenly on the pallet, and not slide on the surface when the button was let go!! Tedious!!
I made three temporary maple buttons until I can find old brass replacements.
The toughest thing was making the netting/screening for under the brass lined air holes on the top of the treble end and the front grill. Everything offered in stores is synthetic and the holes are round or octagonal, not square. I used yellow silk thread from when I restored my grandfathers 1930's bamboo fly rod. I made a primitive "loom" and wove under/over the warp threads and went around nails back and forth for about one and a half inches, then I would glue the threads at the nails to the wood and when dry remove the nails and move up and do another section. When it was done I put two coats of clear shellac to hold it all together then cut it off the "loom". I didn't think it was going to work as well as it did, I think it looks closer to original than anything I could have bought.
I got all my leather and leather valves from Charlie Marshall. I still have to install valves on everything. After I glue reed blocks back in place, I will wax them and everything else that I took apart, I'm waiting until the end so to do it all at once.
I'm picking up materials, folded cardboard and gussets, to make the new bellows in about a week or so, getting it from Frank Morano in Revere, Mass. The bellows will probably be my biggest challenge but I'm going to give it a go anyway!
Once I have the new bellows material I can measure for the printer who is going to duplicate the original bellows papers by digitally copying the original ones. Once I take the old bellows apart to get the center wooden frame out I can bring them to the printer so they can lay them out flat to get the image. It may not be perfect but it will at least make it look like it did originally to some degree, I hope!
At some point, when the money is there, I'm taking it to Bob Snope out at the Button Box in Sunderland Mass. to have him check the tuning, I can't wait for that, should make a difference.

This whole project has been really enjoyable, I love doing this kind of thing and hopefully the instrument will again make music.
Logged

Thomas Barnatt

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Progress update: Meinhold Melodeon
« Reply #1 on: March 23, 2022, 01:50:05 PM »

Part 2
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal