Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Needed: Pair of high F#/G# Liliput reedplates  (Read 953 times)

0 Members and 1 Guest are viewing this topic.

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Needed: Pair of high F#/G# Liliput reedplates
« on: April 09, 2022, 03:53:39 PM »

Hello, I managed to get hold of a Hohner Liliput and was very pleased. However, the original high F#/G# reedplates have been removed and replaced with C#/D reed pairs (non Hohner) and so that nifty little chromatic scale from E up one and a half octaves to C is lost! I realise these reeds are somewhat hard to come by, but I thought I’d take a shot in the dark and see if anyone has these reeds in their spares box, or would be able to grind some out or something… I would very much appreciate any help or pointers in the right direction… Thanks
Logged
Dancing about architecture since 1997

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #1 on: April 09, 2022, 04:15:03 PM »

If any fettlers are able to source or produce these reeds, a PM stating cost etc would be great… thanks
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #2 on: April 09, 2022, 05:14:16 PM »

You can use standard Hohner reeds and file the plates down to the Liliput width.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #3 on: April 09, 2022, 05:38:50 PM »

You can use standard Hohner reeds and file the plates down to the Liliput width.

Great!.. I recently bought a set of Club ii reeds, with the original intention of fitting the C row into the Scarlatti toy and filing down a set of D reeds from the F row… Are they basically the same reeds then? Will there be no noticeable difference in sound?..
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #4 on: April 09, 2022, 07:12:37 PM »

Standard reed plates are a little thicker, but the reeds are spaced the same distance apart.  The Club reeds might have longer tongues for the same pitch.  If they are too long to fit you can choose a higher pitch (shorter) reed and tune down by filing the lower third of the reed tongue.  The sound will be the same
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #5 on: April 09, 2022, 07:49:10 PM »

F#/G#? What tuning is the box in and which row/octave is this reed on? Is it a B/E?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #6 on: April 09, 2022, 08:07:45 PM »

F#/G#? What tuning is the box in and which row/octave is this reed on? Is it a B/E?

It’s the C/F box. The accidentals row of 4 buttons has 2 F#/G# pairs, one at each end. The one at the higher end is missing…
Logged
Dancing about architecture since 1997

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #7 on: April 09, 2022, 08:13:02 PM »

Standard reed plates are a little thicker, but the reeds are spaced the same distance apart.  The Club reeds might have longer tongues for the same pitch.  If they are too long to fit you can choose a higher pitch (shorter) reed and tune down by filing the lower third of the reed tongue.  The sound will be the same

About the longer tongues, just wondering… Is it possible to file the reedplate down shorter at the rivet end instead of finding shorter reeds and tuning them down? I’m guessing this might be a bad idea as the reeds might rotate out of alignment?..
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #8 on: April 09, 2022, 08:40:04 PM »

You may well have to shorten the reed plate too.  But you will match the sound best of you also adjust the scale length. (Scale length is the length of a reed tongue for a particular pitch)
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #9 on: April 09, 2022, 08:48:21 PM »

You may well have to shorten the reed plate too.  But you will match the sound best of you also adjust the scale length. (Scale length is the length of a reed tongue for a particular pitch)

Ah, I see, yes that makes sense. How far might you expect to go up to find a reed to adjust to said F#/G# reed?.. Something higher than a G/A reed say. Is there a limit?..
Logged
Dancing about architecture since 1997

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #10 on: April 09, 2022, 09:26:02 PM »

When I’m back home I will measure the F#/G# reedplates from the club.

In case anyone is interested to know, the required dimensions for this reed to fit into the liliput are 32mm x 14mm…
« Last Edit: April 09, 2022, 09:28:04 PM by Arnold »
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #11 on: April 10, 2022, 10:29:46 AM »


Ah, I see, yes that makes sense. How far might you expect to go up to find a reed to adjust to said F#/G# reed?.. Something higher than a G/A reed say. Is there a limit?..

There is a limit, but it's something you can only discover by going too far!!

If you look at the highest reeds on old Hohners you will see that both tongues are the same length and there is a short section near the rivet on the higher pitch reed where the metal is still full thickness with a blue surface.  I usually find that reeds like this can easily be tuned down by 3 or 4 semitones without compromising the reed.  The lower reed will usually go done by one or two semitones.  What you can't do with the high pitches is to tune them much higher.  A semitone is possible with great care, but the reed tip can become very thin and fragile.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #12 on: April 10, 2022, 02:34:18 PM »



There is a limit, but it's something you can only discover by going too far!!

If you look at the highest reeds on old Hohners you will see that both tongues are the same length and there is a short section near the rivet on the higher pitch reed where the metal is still full thickness with a blue surface.  I usually find that reeds like this can easily be tuned down by 3 or 4 semitones without compromising the reed.  The lower reed will usually go done by one or two semitones.  What you can't do with the high pitches is to tune them much higher.  A semitone is possible with great care, but the reed tip can become very thin and fragile.

Really helpful information, thanks! I’ll be seeing what I have in later, taking measurements etc. Just one more question for now… what type of files etc are sufficient for filing down reedplates, leaving a nice finish etc?..
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #13 on: April 10, 2022, 02:42:58 PM »

Files of the best quality you can find.  Genuine swiss files by Grobet or Vallorbe.  I've tried using cheaper files but they get dull in a very short time when filing spring steel.  This a a good one from Axminster tools to start with and is relativly inexpensive. For very small reeds a needle file is easier to manage.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Needed: Pair of high F#/G# Liliput reedplates
« Reply #14 on: April 10, 2022, 10:30:13 PM »

Thanks Theo, that doesn’t look to bad! Could that be used for the reedplate ass so well as the reed itself?

I just measured the club reedplate (it’s from the original Club ii with a half row of just 4). The F#/G# reedplate measures 34mm x 16mm, so 2mm more each way the closest reed I could measure on the liliput. Would that be ok? The reed which best matches the length of the liliput reedplate is the Bb/C reed 4 semitones higher, so I’m guessing something in between might be better?..
Logged
Dancing about architecture since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal