Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner reeds with a \  (Read 1480 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Hohner reeds with a \
« on: April 21, 2022, 04:26:25 PM »

I’m restoring a little Hohner PA (a 'Vineta'…not a model I’ve seen before but identical to a Verdi I inside, and I’ve seen lots of those). The big bass reed pairs are H reeds, with Dural/aluminium reeds. The chord bass reeds are marked with a T and zinc (I think..it’s darker and heavier than the dural). The treble are all zinc but marked with a \ on the top right hand corner. I assume these are just another incarnation of Hohner reeds?  Anyone like to comment? Theo?
« Last Edit: April 21, 2022, 04:30:52 PM by RogerT »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner reeds with a \
« Reply #1 on: April 21, 2022, 06:00:08 PM »

I’ve seen those too Roger on diatonics.  I think they are only found on instruments from the early 30s.  I don’t know anything of their origin, but I can speculate that it was a time of rapid expansion for Hohner and perhaps they sub-contracted some reed making??
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner reeds with a \
« Reply #2 on: April 21, 2022, 07:23:28 PM »

Thanks. Yes, that sounds right. Some (but not all) of the rivets have been hammered. But the tolerance of the tongue in the slot looks about the same as ordinary Hohner reeds, so I don’t think they are different apart from the markings.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner reeds with a \
« Reply #3 on: April 21, 2022, 08:22:53 PM »

The ones I’ve seen were thinner than typical H or T reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

BoxPlayer

  • Member
  • *
  • Offline Offline
  • Posts: 31
Re: Hohner reeds with a \
« Reply #4 on: October 05, 2022, 02:20:30 PM »

As far as I can see nobody has commented about the left leaning mark  (  \ ) on the top right corner of the reed. This is also common accordion reeds and I have understood this was to identify the outer reed. This is necessary since the tuning for interior/exterior reeds is different.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hohner reeds with a \
« Reply #5 on: October 05, 2022, 04:30:19 PM »

You are correct, BoxPlayer.  The 'H' or 'T' usually found on Hohner reedplates plays the same role of identifying the outer side, in which case the slash is not required.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal