Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Register modification  (Read 1037 times)

0 Members and 1 Guest are viewing this topic.

melodona

  • Member
  • *
  • Offline Offline
  • Posts: 31
    • Melodona Accordions
Register modification
« on: May 06, 2022, 07:57:30 PM »

Hello there,

So the register modification I need to do is just about cutting a little wing here and adding a little wing there, and it looks simple enough, but I wonder about how to make sure it'll hold without taking too much space, which would make the sliders rub against each other.

How do you usually go about doing this kind of modification? Not sure about soldering...

Thank you for any tips you might have.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Register modification
« Reply #1 on: May 06, 2022, 09:35:42 PM »

Not something I’ve done, but most of those sliders are aluminium so that will make soldering more difficult.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Register modification
« Reply #2 on: May 06, 2022, 10:30:39 PM »

What effect are you hoping to achieve? You might be able to cut off a wing with tin snips. And I’d probably superglue a new wing cut from thin brass sheet, so obviously this will double the thickness of the slider…where the new wing overlaps onto the slider. But first you’d need to get the sliders apart …and I’ve always shied away from that. They may not easily come apart.
But…normally most reed combos are covered by the existing couplers…and there is a risk that you'll mess up the coupler mechanism, so you need a fall back plan.
« Last Edit: May 06, 2022, 10:33:21 PM by RogerT »
Logged

melodona

  • Member
  • *
  • Offline Offline
  • Posts: 31
    • Melodona Accordions
Re: Register modification
« Reply #3 on: May 07, 2022, 01:12:29 AM »

The goal is to replace the bassoon - piccolo option by a bassoon - clarinet option. All together, it's pretty straight forward: just cutting off two wings (that's the easy part) and adding two wings. The sliders come apart easily. My little iron is not cut out to work with aluminum. I'm wondering if glue (of any type) would be strong enough, considering I can't lay it on thick.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Register modification
« Reply #4 on: May 07, 2022, 07:10:15 AM »

I’d try superglue. I’ve had good results with it e.g. attaching a metal grill bracket to a metal fondo. I use it for all sorts of things. Not having the 'bandoneon' combo is pretty annoying, I agree.
…leave the glue to cure for a couple of hours. It rarely works instantly.
« Last Edit: May 07, 2022, 07:14:48 AM by RogerT »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Register modification
« Reply #5 on: May 07, 2022, 08:19:42 AM »

For a strong glued joint metal  to metal epoxy is stronger than CA.  Make the contact area as large as you can.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Register modification
« Reply #6 on: May 07, 2022, 12:30:01 PM »

For a strong glued joint metal  to metal epoxy is stronger than CA.  Make the contact area as large as you can.
Sounds interesting...the world of glues... endlessly fascinating. I will try this stuff

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Register modification
« Reply #7 on: May 07, 2022, 12:33:12 PM »

I didn’t mean “metal to metal” epoxy!  Just that for metal to metal joints epoxy will be stronger
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Register modification
« Reply #8 on: May 07, 2022, 01:06:19 PM »

The crucial thing is surface preparation. The aluminium will have a fine, invisble, surface layer of oxide - you need to bond to the aluminium beneath that.
Wipe it over with a solvent to remove any surface debris and grease, then abrade the area where you want to glue, another quick solvent wipe and then glue it as soon as the solvent has evaporated off. (Before any new Oxide can form - which is very soon)

If you're using epoxy I'd have it mixed and ready to use before cleaning and abrading.
CA can also give a strong bond, I like 'ZAP' medium CA as it is slightly thicker so much less inclined to run and stick unintended bits and fingers together.
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Register modification
« Reply #9 on: May 07, 2022, 01:40:52 PM »

Worth considering as an alternative to attaching a new wing. There is one wing you can remove which should give you LM on the LH coupler, but only if you go to it from the master LMH coupler.

The only downside is that it may take a couple of nano-seconds longer to press two couplers consecutively, (not simultaneously of course) if you are changing your combination mid-tune.

The hard part is to identify which wing to remove as you don't get a second chance if you choose the wrong one.   :-[

Hope this helps....
« Last Edit: May 07, 2022, 01:45:24 PM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Register modification
« Reply #10 on: May 07, 2022, 02:31:26 PM »

I suggest using the same material as the original (aluminum) as the thermal coefficient of expansion of aluminum is quite different than brass or steel and may cause joint stress if subjected to wide temperature flucuations . 3M makes some very strong 'permanent' double-sided tape that is pretty thin and may be a good option. Epoxy is good with site preperation as mentioned above.

Scott
Logged
too many boxes...please buy one, or two, or

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Register modification
« Reply #11 on: May 07, 2022, 02:44:32 PM »

Given the risk I would probably try making a substitute slider. That way I could reinstate the original. I'd forget about soldering (personally), ditto epoxy...but that's how I'd tackle it. Getting the replacement totally flat after cutting etc would be one of the challenges. Placing it between two flat pieces of steel and hammering from both sides is how I straighten kinked sliders
 
Or make it from plastic sheet

« Last Edit: May 07, 2022, 03:22:14 PM by RogerT »
Logged

melodona

  • Member
  • *
  • Offline Offline
  • Posts: 31
    • Melodona Accordions
Re: Register modification
« Reply #12 on: May 07, 2022, 03:26:53 PM »

Wipe it over with a solvent to remove any surface debris and grease, then abrade the area where you want to glue, another quick solvent wipe and then glue it as soon as the solvent has evaporated off. (Before any new Oxide can form - which is very soon)

Thank you all so much for your answers. I'm traveling with limited tools, I'll have to buy a solvent. Graham, do you recommend a particular kind or brand?

I also don't have access to the box of metal scraps I have back home, so I'll have to go hunting for something that would be my metal grill bracket. Again, if anyone has suggestions of what would work best, I'm all ears.

Thanks again!
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Register modification
« Reply #14 on: May 07, 2022, 06:35:41 PM »

I'm sure to be wrong here, but I find that a tin of lighter fluid does the job, and it's readily available all over the place, and cheap as well.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Register modification
« Reply #15 on: May 07, 2022, 11:03:38 PM »

Wipe it over with a solvent to remove any surface debris and grease, then abrade the area where you want to glue, another quick solvent wipe and then glue it as soon as the solvent has evaporated off. (Before any new Oxide can form - which is very soon)

Thank you all so much for your answers. I'm traveling with limited tools, I'll have to buy a solvent. Graham, do you recommend a particular kind or brand?

I also don't have access to the box of metal scraps I have back home, so I'll have to go hunting for something that would be my metal grill bracket. Again, if anyone has suggestions of what would work best, I'm all ears.

Thanks again!

I don't think the choice of solvent is too critical.
My 'go to' for cleaning up many things (but not plastics / rubber) is automotive brake cleaner,  but Isopropyl alcohol is good and easy to get hold of, or methylated spirits (Denatured alcohol).  Anything that will take any grease / dirt off and evaporate without leaving a residue should be fine I guess.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Register modification
« Reply #16 on: June 03, 2022, 04:36:40 PM »

I have done this modification a couple of times for customers. I used superglue to position the slider tooth and made sure it was placed properly. I secured it with tiny aluminum rivets (1mm or so) after drilling 2 holes through the glue joint.
 This works really well since everything stays in place while you are drilling and riveting.
You can file the heads of the rivets down a bit if clearance is an issue but it does not seem to be a problem
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal