Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: pallet pad adhesive  (Read 2224 times)

0 Members and 2 Guests are viewing this topic.

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
pallet pad adhesive
« on: June 05, 2022, 03:39:02 PM »

So I am replacing the pallet pads on my Hohner Pokerwork, mostly because of minor air leak on the bass side.
When I took the pallets off, I realized it already has newer felt-suede pads, and one of them is slightly off-centered which is probably what allowed air leak. Alas, off they are, and I will proceed with the replacement work.

Here is the question, the replacement pad was taped on it with double-sided tape, vs. Mr. Lester Bailey's PVA. Is one adhesive better than the other?
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: pallet pad adhesive
« Reply #1 on: June 05, 2022, 04:29:27 PM »

I would recommend the "Mr. Lester Bailey's PVA" method. More importantly I see from the photo that at least on leather had been installed the wrong way round with the shiny face being used as the sealing surface, this will always leak. THe correct sealing surface is the soft/compliant side.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: pallet pad adhesive
« Reply #2 on: June 05, 2022, 04:30:41 PM »

PVA 100%
Logged
C#/D player

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: pallet pad adhesive
« Reply #3 on: June 05, 2022, 05:04:34 PM »

Personally I recommend gum arrabica or hide glue.
I have found that gum arrabica has perfectly adequate hold for both pallet facings and bellows tapes.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pallet pad adhesive
« Reply #4 on: June 05, 2022, 05:23:36 PM »

When applying any liquid or gel adhesive, it should not be applied direct to the felt and only the smallest amount that gives good adhesion should be used.  This is to avoid adhesive soaking into the felt and hardening it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pallet pad adhesive
« Reply #5 on: June 05, 2022, 05:26:43 PM »

More importantly I see from the photo that at least on leather had been installed the wrong way round with the shiny face being used as the sealing surface, this will always leak. THe correct sealing surface is the soft/compliant side.

I don’t have any evidence to support this.  Concertina pads usually have the smooth side of the leather as the sealing surface, so it’s possible that either may work.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: pallet pad adhesive
« Reply #6 on: June 05, 2022, 06:59:41 PM »

Personally I recommend gum arrabica or hide glue.
I have found that gum arrabica has perfectly adequate hold for both pallet facings and bellows tapes.

I've used both PVA and Titebond liquid hide glue (yes, I do have a traditional hot glue pot, but the pre-prepared stuff is so much quicker and easier when you only need small quantities) and both have been perfectly staisfactory. Down to personal preference (or what's to hand at the time) I guess.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: pallet pad adhesive
« Reply #7 on: June 05, 2022, 07:52:17 PM »

Thanks for all the input!
I tried the double-sided tape first since I thought it would be a simple and reversible method -- and it didn't even stick to the felt. So Mr. Lester Bailey's PVA it is  ;D

The pallet pads I took off all have shiny side out, I suspect it was made this way. One of the pad also has a knife cut mark over the leather, which probably didn't help.

I also replaced the pad for the air key, which was original leather pad without felt. My air key IS the one that leaks air with hard bellow push, but I think the culprit may be the spring. I can prevent air leak by holding the air key tight when push. I may need to order replacement spring/valve mechanism from across the ocean after all.

All in all this is fairly straight forward. Thanks again for all your help!
Logged

chris hall

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 245
Re: pallet pad adhesive
« Reply #8 on: June 05, 2022, 08:17:56 PM »

your air valve mech looks in good condition so probably no need for replacement. you might find with fresh felt/leather it seals fine. Give it a week or so as ive found sometimes they bed in. If it still leaks you can bend the existing spring to give more tension on the lever. Alternatively its not hard to make a new spring using piano wire. For a stronger spring use thicker wire or less coils or make the arms further apart. Wind the wire round a drill bit of appropriate size glued into a piece of wood. your drill bit has now changed its name to a mandrel (or at least thats what i call it)......alternativley hohner spares sell new springs.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pallet pad adhesive
« Reply #9 on: June 05, 2022, 11:08:13 PM »

Before making the spring stronger check that the pallet is lying flat.  Press firmly in the centre and watch to see if any edge or corner moves down more than the others as the felt compresses.  Bend the lever to correct if there is an error
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: pallet pad adhesive
« Reply #10 on: June 05, 2022, 11:44:32 PM »

Is there a possibility a broken  bass spring has been replaced with the wrong spring. I did that once. The pad didn't seal well
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: pallet pad adhesive
« Reply #11 on: June 06, 2022, 02:49:25 AM »

I did check to make sure the air valve pallet is square/flat on the board. I noticed the air leak there before I replaced the pallet pads, but unfortunately replacing the pallet pads did not fix the issue.
I am attaching another picture -- the spring on the air valve is not in its base condition -- I assume somebody tried to fix it at some point. I tried to open up the arms a bit more myself as well -- did not increase the tension much either. I suspect Greg is right about it being the wrong sized spring.
Doing some research, I think the treble side springs are 0.6mm, bass side 0.65mm, and air valve 0.7mm. I know these parts are fairly inexpensive, I may just have to pay for the shipping to get it.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: pallet pad adhesive
« Reply #12 on: June 06, 2022, 06:40:09 PM »

When the pallet is removed from the lever for the initial changing of felt material, be sure that that all of the glue/wax is cleaned out from the channel that the lever rests on before reinstalling;  if its a really snug fit, what sometimes happens is when the lever is pushed down into the pallet channel (compressing the new felt/leather material slightly) the pallet itself will lift back up slightly when you let go, resulting in a less-than-perfect seal once it's glued/waxed into place.  I always make sure that the channel is cleaned out properly and even sanded down if necessary to ensure that the lever rests freely on the pallet and does not have any 'purchase' on it until it is glued/waxed into place.  It's happened to me and at least one other person I know on a few occasions when extra care was not taken.
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: pallet pad adhesive
« Reply #13 on: June 06, 2022, 08:17:12 PM »

A rookie mistake is to position and glue the pallets back in place before checking for air tightness. Assemble, hold up to light to check for little chinks of light and do a compression test (by assembling sans reed blocks) before putting glue or wax anywhere near it. From your original post it seems you could have avoided a time consuming repad by diagnosing the air leak (as a badly positioned pallet) if you had done this first. But never mind..you’ve found out about repadding etc. Also there isn’t always a right way to do stuff. Repairers have differing opinions (as I have discovered a few times). The convention is to have the leather nap downwards, but as Theo points out, concertinas do it the other way around. If it works that’s ok, which ever way you have it. I’ve seen accordions with the felt layer downwards…and this really doesn’t work.

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: pallet pad adhesive
« Reply #14 on: June 14, 2022, 02:34:20 PM »

This thread is filled with great advice, not just on adhesive! Thank you all!

I will do a little update here.
I managed to tighten the air valve spring with an extra roll over the shaft. Not the most beautiful looking job, but it works well and stopped the air leak from a heavy push.
I replaced the treble side pads as well -- it had leather-only pads, though no air leak issues. I have planned on replacing all the pads so materials were already purchased. Everything looked fine until after I adjusted the button height... and I have air leaks on a heavy push on the treble side now!
I think mselic is correct about the pallet moving on the arm, although I'd honestly say I have done a pretty thorough cleaning on everything. I may try reposition/re-glue a few pallets.

But I should probably clarify a bit -- truthfully the instrument is in great playing order both before and after the repadding, just not as air-tight as my new Panther, which I barely touch nowadays. I think it just needs minor tune ups, which I am learning a great deal doing it!  Thank you all for the helpful comments!!
Logged

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: pallet pad adhesive
« Reply #15 on: June 14, 2022, 02:57:59 PM »

Nice job!  Regarding airtightness, you mentioned the air button was a culprit, and I'm sure the spring helped, but there's another potential issue that can arise:

The original pads are thin leather, and when you re-pad with nice thick leather+felt, it changes the resting position of the buttons.  This is fine in most cases and you can level out the treble and bass key mechanisms with careful tweaking.  But I've found there's often a sneaky issue with the air button: its natural resting position can just a little higher than is allowed by its slot in the bass plate.  You can fix it either by carefully bending the air button shaft or by using a round file to enlarge the slot slightly.

The first time I experienced this it took lots of disassembling, performing light tests, verifying it was all tight, reassembling, finding a faint leak, cursing, disassembling again...  etc.  Until the light bulb (metaphoric this time) moment.

(Edit: I'd echo Roger's advice above, regarding gluing last, for the treble side.  As much as it may seem like taking a step backward, if I were in your position I'd remove the treble pallets and re-glue them now that you have the button heights adjusted.)
« Last Edit: June 14, 2022, 03:01:03 PM by Gonk »
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: pallet pad adhesive
« Reply #16 on: June 14, 2022, 06:19:28 PM »

If you fit thicker pallet material it is more or less essential to remove the pallets from the arms and reseat them as the angle between the arm the pallet face will have changes and the heel (axle end of the pallet) will hit sooner and the tip end may well not meet the soundboard.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: pallet pad adhesive
« Reply #17 on: June 19, 2022, 11:24:28 PM »

If you fit thicker pallet material it is more or less essential to remove the pallets from the arms and reseat them as the angle between the arm the pallet face will have changes and the heel (axle end of the pallet) will hit sooner and the tip end may well not meet the soundboard.
Totally. And if you are ever renovating one of the old German type boxes with screwed/nailed pallets dont even go there with anything other than like for like thin leather facings. Unless you also tune reeds with a dremel.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal