Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Colliding Reeds  (Read 1156 times)

0 Members and 1 Guest are viewing this topic.

BoxPlayer

  • Member
  • *
  • Offline Offline
  • Posts: 31
Colliding Reeds
« on: July 26, 2022, 09:45:36 AM »

 Clashing reeds.
I am presently working on a small diatonic melodeon where the lowest treble notes are C3 and CSharp3  (1 octave below middle C) It is MMM arrangement with some musette though this matters less at C3 level. The 0 tuned reed faces the — tuned reed and there is only about 5mm between the two reed faces. With average bellows pressure the reed travel/excursion allows the reed to ‘collide’ with the valve opposite (not a nice sound). Interestingly it seems that the —tuned reed is the culprit because blanking it off cures the problem while blanking off the 0 tuned reed does not. The reed tips have lead added at this frequency and as far as I can see the reed tips are all set at about the same height.
I’d be interested if anybody has any suggestions or ideas about a possible cure.
Logged

Sam Wilson

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Colliding Reeds
« Reply #1 on: July 26, 2022, 04:16:54 PM »

Is there room between the bases of adjacent blocks to turn one of the reed plates around so the free end of one is opposite the rivet end of the other?  Or you could carve a rabbet in the block to set the problem plate into the block a couple millimeters.  On second thought, that might cause the reed on the inside of that plate to collide with the block, so maybe not.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Colliding Reeds
« Reply #2 on: July 26, 2022, 10:08:08 PM »

I agree re trying to set the plate into the block a bit. It might only need a little more clearance. Or you could try that with both facing reeds to gain 2 or 3 mm (although it might then strike the back of the reed chamber if you set it in too far).

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Colliding Reeds
« Reply #3 on: July 26, 2022, 11:28:23 PM »

A possible cure consists in angling the blocks through modifying their soles.
Logged

BoxPlayer

  • Member
  • *
  • Offline Offline
  • Posts: 31
Re: Colliding Reeds
« Reply #4 on: July 27, 2022, 09:27:37 AM »

Thanks all for responding.
The suggestion to reverse the reed in its slot, to have the vibrating tip at the bottom, is an innovative answer. Unfortunately the bottoms of the reed blocks are the normal type and the bottoms are even closer than the top so is impractical at the moment. I am considering all your suggestions and will report any progress in due course.
I am considering lowering the tip of the reed (re-voicing) in the hope that it will reduce the travel of the reed. It might make it less responsive to play but this might be less important with this very low note.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Colliding Reeds
« Reply #5 on: July 27, 2022, 09:47:19 AM »

If the blocks are angled could you mount the plates a little further from the Fondo?
Chisel out a little from the top of the blocks inside the slot so the plates can slide up, then fit a little sliver of wood, matchstick, coffee stirrer or the like at the other end.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Colliding Reeds
« Reply #6 on: July 27, 2022, 11:21:28 AM »

Sometimes you can get away with moving the blocks slightly further apart.  You will have to  move the locating  blocks and add a packing piece between the blocks.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Colliding Reeds
« Reply #7 on: July 27, 2022, 12:50:33 PM »

Blocks placed too close (or not properly angled) are an annoying design fault. Often, the collision doesn't occur before the reeds are "played in".  Reversing works only with the smallest reeds. I still think that beveling the reed block soles is the best solution (basic woodwork skills are required).
Logged

BoxPlayer

  • Member
  • *
  • Offline Offline
  • Posts: 31
Re: Colliding Reeds
« Reply #8 on: July 27, 2022, 07:46:25 PM »

I’m pleased to say I have made a solution of sorts. Rather than rush into any major wood alterations my instinct was that the makers, Casali, had probably made the reeds playable when it was new and that a change had occurred when they were cleaned/voiced/tuned, re-valved and waxed.
I started by lowering reed tips to the point where they were just about to ‘choke’. This seemed to reduce the amount the reed was travelling. Also I noticed that too much tremolo/musette caused the reed to travel more as well as it tried to ‘beat’ with its neighbour. So reducing the tremolo helped as well. The end result is a very slight tremolo but it does sound largely ‘in tune’. Getting any sort of musette, which is pleasant to the ear, is difficult even with the low F3 on normal piano accordions. I haven’t seen or heard much discussion on tuning those reeds from say G3 down.
Once again I thank all for their suggestions and sharing the problem.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal