Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Club Model I  (Read 1888 times)

0 Members and 1 Guest are viewing this topic.

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Hohner Club Model I
« on: August 17, 2022, 08:34:42 PM »

AKA What have I gotten myself into!?
I saw it on ebay for $120, and thought of my beloved GC Pokerwork, thinking, WHAT A DEAL!... not realizing it is a completely different instrument!

So, it is in CF, haven't gone through the bass to figure out what notes they are yet, but I think it's the same as the posted CF Club finger chart. (To be fair, it is hard to search just "CLUB" on this board and get the relevant information.)

All right, so here's the damage assessment...
1) Air leaks! There are at least 6 holes on the bellow inside corners (leather?) that light can shine through. --- What should I do to patch them?
2) Reeds: need rewaxed (two of them have fallen off the bank), need new valves (which I have not done myself yet... although it can't be THAT difficult, right?), broken reeds (4 total, on different notes, so I may be able to get by without replacing them... what causes reeds to break, though?), and half a dozen poorly vibrating reeds (not centered? rusts? dirt?), and minor rusts here and there.
3) Loose/crooked pallets (I can fix this easily with some hot glue), and probably should just replace the pads (which I also have on hand). It appears someone at some point have replaced some of the pads and pallets, but probably a long while ago.
4) Exterior: missing one bass button. Looks to be the same as the Pokerwork mushroom button, at least it is still available. Somebody tried to paint over a few treble buttons but didn't do a very good job. I may just sand/polish them. The shoulder strap is also super short -- may have been set up for a kid before.
5) Tuning... (what tuning!?) haven't confirmed the pitch it's tuned to yet. I suspect it's not to 440.

All right... I guess I need help.  ::)  ...or, should I just give up and hand it to someone more experienced?
(not to mention I have not played a Club box ever -- and probably don't need to -- pretty sure I am set on GC)

attaching some pictures.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Hohner Club Model I
« Reply #1 on: August 17, 2022, 08:46:10 PM »

I've just looked at the last picture and I can see why you are struggling with the keyboard.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Hohner Club Model I
« Reply #2 on: August 29, 2022, 03:39:12 AM »

So I noticed these pins/nails around the reed plates, some of them getting loose. I assume the idea was to help holding the reed plates down.
Now I am about to re-wax the reeds, do I keep these pins/nails, or can I go without them?

Truthfully I am unimpressed with them, and I feel a good solid amount of wax would do better. ?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Club Model I
« Reply #3 on: August 29, 2022, 06:59:49 AM »

Your instinct is good.  The pins serve no useful purpose.  You have the evidence that they do not prevent reeds falling out when the wax has failed. Discard them.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Hohner Club Model I
« Reply #4 on: August 31, 2022, 11:40:29 PM »

ouch! I think this is an actual total loss, mostly because of the damaged bellow.
From my understanding there is no (reasonable) way to replace the leader corners. Maybe there is a way to seal the holes, i am curious if somebody has experiences on that.
I found several boxes on flea markets that are over 70 years old with intact bellows. (btw, is it advisable to grease the leader corners?)
Broken reeds can be replaced, valves can be replaced, layout can be changed, bass buttons can be replaced, and also the bellow could be replaced but a new one would cost you about 170 - 200 €.
My journey startet with an old Erika (payed about 30€), a ww2 Club box also, but it was in a good state, so good there was no need for new reeds, the reeds were removed, washed in aceton and revalved and rewaxed. Old boxes are rickety and can be repaded also, but this is not always necessary.
I must admit that i am at the very first start of my journey, it attracts me as a hobby, but i think you should
separate it from makin music, wich takes alot of time too if you are new into diatonic instruments. I am indeed and i think of it as a kind of brain jogging, the other thing is handcrafting with many different aspects. And in the end you have to learn to tune the box wich requires a tuning table, some tools and nerves of steel.
Sorry, i feel i am not dignified to answer your question because i know on this board there are many experienced professionals, but i feel somehow solidary with you and i doubt many of them would have gone the journey to the end if they had knew what obstacles they had to conquer. The good point: those old Hohner boxes are very nice instruments, well made, small and lightweight and sounding good. I am from Germoney, and the club system was very wide spread over here but nowadays dead as a dodo. Alot of work for a good  Handzuginstrumentenmacher (!) to convert them all into english melodeon! Such a pity, thousands of those old boxes are rotting on attics because it does not pay off to get them restored, if you cant do it for yourself it is about 500€ to get them back to live.
« Last Edit: August 31, 2022, 11:43:42 PM by Stefan »
Logged

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Hohner Club Model I
« Reply #5 on: September 01, 2022, 12:18:05 AM »

the club system is a german system (invention) and it has a "Gleichton" in the middle of the inner row wich produces the same note on push and pull the bellow. The main goal (afaik) was to enable players to make music without regular notating system. There was used a five lined note system where the middle line (b) represented the "Gleichton" The half note steps going "down" from the middle line (normally b oder H in germany) represented the bottons underneath the "gleichton" and vica versa upwards wich results in a maybe easier notating system, independent from the tuning of the instrument, nevertheless C/F is the most common setup in germany.
Logged

Dennis Steckley

  • Good talker
  • **
  • Offline Offline
  • Posts: 77
  • Club System!
Re: Hohner Club Model I
« Reply #6 on: September 01, 2022, 12:47:10 AM »

Yes, club system with a gleichton--the way God intended! ;D
Logged
Hohner Victoria Club ii, Hohner Club III M, Hohner Liliput, Hohner Preciosa, Hohner Piccoletta, Hohner Overture LMMM (and three PA's, including one that is the same size as a Preciosa)

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hohner Club Model I
« Reply #7 on: September 01, 2022, 02:30:44 AM »

The way I see it, main problems are the leaking bellows and broken reeds.  Holes in the leather lozenges can be repaired with thin leather, but I remember reading here if you have 10+ leaks, better to replace bellows, so...  Maybe your best solution is buying another old CF Club Hohner with the same size bellows (hopefully not leaking) and H reeds (hopefully not broken).  There are plenty of CF Hohners around...     
Logged

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Hohner Club Model I
« Reply #8 on: September 01, 2022, 04:59:09 PM »

Sorry I have been slacking off on this project -- adding two windows to the house instead. I think I will rather enjoy pulling my hairs out working on the Club instead of pulling old nails out of plaster lath.

I got the pallets pulled and cleaned up, ready for refacing. also got the cracked bass cover board glued back nice and tight. (Titebond III for the impatient woodworkers with fast clamping skill)
I am trying to work out a order list for Charlie for all the parts I may need. My thinking is I will do as much as I can until I really need professional help  :D

I searched the forum on gusset patching (I am hoping I only need to patch a few pin holes instead replacing the whole thing), there were some good info by our forum sages here. So I am a little less scared to do it. or I might just try dabs of liquid membrane (for bathroom construction) or acrylic paint. (ok, you guys can yell at me later)

My bigger worry right now is the reeds. a lot of them simply don't sound. Some of them make clinking noises, and of course, the broken ones I am not sure I will be able to find replacement. I am hoping some good cleaning will resolve most of the issues, but I am reluctant to take them off the bank before making sure I know which keys they are. (or perhaps I can build a single block jig for testing/tuning?)
Also, I do need recommendations -- a task further down the line, but important now for my shopping list -- should I replace the old leather valve with leather, or the vinyl valve? What's the difference, pros and cons?

Thanks Theo for the always insightful comment, and Stefan for the solidarity!
Logged

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Hohner Club Model I
« Reply #9 on: September 01, 2022, 07:38:00 PM »

dont worry about  the small nails that hold the reeds. There are some (french.) vintage boxes that
had no wax at all, the reedplates were nailed on a leather surface and it was air leak proof also.
I think historically the wax came later and they kept the nails for easier waxing (no solder irons then) and
for security, if the wax gets old or the instruments get heavy impacts the reeds would stay in place.
I am dreaming of a system that alows easy "click in" of the reedplates, that would allow to try out different
setups. Somehow user serivuceable. The nailed only system is closer to that than waxed blocks.

Logged

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Hohner Club Model I
« Reply #10 on: September 07, 2022, 05:18:07 PM »

So I took all the reeds off, cleaned off the old wax in acetone in ultrasonic bath, and then Evapo-rust for 8 hours (also in ultrasonic bath, because I can).
They look beautifully shiny, and most importantly, they all sound! (a few required re-aligement of the reed tongue)
Evapo-rust really does work well in removing the rust, but also the bluing.  :P  (I do have bluing chemical, although I am not sure how critical it is to re-blue the reeds.)

The reed banks are thoroughly cleaned as well. I scraped off the old wax and dusted off all loose particles. I then used a hair dryer to melt any residue wax dust in place. I tried to use xylene to wipe everything off first, but hair dryer was a lot easier.
I ordered some new vinyl/vileda valves from Charlie. 

I guess I can start tuning the reeds. Pretty sure they were tuned to A=435. just need to remove material at the tip to raise the pitch, right?
I am using the open source Tuner app on my phone https://f-droid.org/en/packages/org.billthefarmer.tuner/
Does anyone know how many cents apart I need for a Club box? (or should I tune it drier?) This is going to be a real learning experience for me.  ::)

Unfortunately, I will also need to replace 5 reeds. Any suggestions on sourcing the replacement reeds is greatly appreciated!


My wife says this is labor of love. I think I am just begging for punishment.
It is rather amusing to think this box is close to 90 years old, and made in interwar Germany. How did it end up in Florida US?
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Hohner Club Model I
« Reply #11 on: September 07, 2022, 05:29:11 PM »

http://forum.melodeon.net/index.php/topic,26461.msg316116.html#msg316116

This is a tuning curve suggested by Steve freereeder.
It will work well for your club box. Enough fizz to make the box sound alive but drier than standard Hohner.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Hohner Club Model I
« Reply #12 on: September 07, 2022, 11:21:06 PM »

http://forum.melodeon.net/index.php/topic,26461.msg316116.html#msg316116

This is a tuning curve suggested by Steve freereeder.
It will work well for your club box. Enough fizz to make the box sound alive but drier than standard Hohner.

I agree with the above. I have declubbed and tuned a couple of Model 1’s using this curve and it works well.  I also picked up on using 600 grit diamond files for fine tuning in one of Steve’s posts.  Great advice. Triangular sets of 6 work best. You need six for tuning a box (ebay).
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Fanie

  • Good talker
  • **
  • Offline Offline
  • Posts: 91
Re: Hohner Club Model I
« Reply #13 on: September 27, 2022, 01:48:10 PM »

For replacement reeds you can contact Harmonikas.cz
Ladislav Titlbach
harmonikas@harmonikas.cz
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal