Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Do you have to use a tuning table?  (Read 2650 times)

0 Members and 1 Guest are viewing this topic.

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Do you have to use a tuning table?
« on: September 14, 2022, 04:21:52 AM »

So I started tuning the Hohner Club 1 reeds after removing all the rusts.
I started out with the lowest bass reeds, and noticed they are all about 60 cents flat. It was probably originally tuned to 435, so I was expecting everything to be flat.
Then I realized when I blow softer it also go about 20 cents sharper... yes, I am blowing the reeds on the reed block to tune it, instead of using a tuning table.

Uhhh, am I tuning the reeds sharp because I am not supplying the right amount of air? Can I really tune the reeds by blowing it without using a tuning table?


EDIT:  I just tried it on my known properly tuned Panther, blowing it [by mouth] does make the note ~40 cents flatter, vs the normal bellow pressure. oh crap.
« Last Edit: September 14, 2022, 04:32:53 AM by jarviw »
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Do you have to use a tuning table?
« Reply #1 on: September 14, 2022, 07:21:55 AM »

A tuning table is quite useful and v easy to make with old PA bellows..plus normal advice is not to suck because there is a risk you will inhale something ..and you really do not want to do that.
« Last Edit: September 14, 2022, 07:23:59 AM by RogerT »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Do you have to use a tuning table?
« Reply #2 on: September 14, 2022, 08:02:24 AM »

I don’t think you can get a good result by blowing by mouth.
You can get excellent results, the best in fact, by using the instrument to sound the reeds.  You have to isolate one bank of reeds with masking tape under the reed block.  You also need a way to suspend the bellows while you work.  I have photos somewhere, I’ll try and find them.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Do you have to use a tuning table?
« Reply #3 on: September 14, 2022, 08:11:46 AM »


I don’t think you can get a good result by blowing by mouth.
You can get excellent results, the best in fact, by using the instrument to sound the reeds.  You have to isolate one bank of reeds with masking tape under the reed block.  You also need a way to suspend the bellows while you work.  I have photos somewhere, I’ll try and find them.

I use this for tuning 1 rows

https://photos.app.goo.gl/WVytNZTFCpNvs5KE9
https://photos.app.goo.gl/6j7TjLo3gJA6yTR66

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Do you have to use a tuning table?
« Reply #4 on: September 14, 2022, 08:28:16 AM »

That’s the boy Lester.
I use the same type of device for all tuning.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Do you have to use a tuning table?
« Reply #5 on: September 14, 2022, 11:13:32 AM »

I use this for tuning melodeons (in particular one rows…but Hohners generally fit on there).

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Do you have to use a tuning table?
« Reply #6 on: September 14, 2022, 12:55:59 PM »

I spent quite a bit of time and effort making a set of foot operated tuning bellows, which I'm really happy with. There are pictures of it on melnet somewhere (?).
But, I most often use a set up very similar to Lester's and (presumably) Theo's, but it has adjustment for other lengths of bellows, the butterfly nuts on the screws in the slots can just be seen on the right this picture. (It's almost 3000miles away at the moment, and this is the only picture I could find on my Google stuff, sorry for the other junk on there.)
« Last Edit: September 14, 2022, 12:57:58 PM by Winston Smith »
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Do you have to use a tuning table?
« Reply #7 on: September 14, 2022, 02:07:05 PM »

Thanks for all the pictures!
I am not following it completely though... how do you use this bellow setup? Do you basically tune the reeds in the instrument, but just mount the box on top as opposed to worrying about the bellow pins?

I think I can make a little board to sit on top of the original bellow easy enough, with an air hole in the middle.


That said, I think I tuned all four low bass plates 40 cents sharp... with a lot of material removed.  :P  :P   Hopefully I have not completely destroyed them...
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Do you have to use a tuning table?
« Reply #8 on: September 14, 2022, 02:59:14 PM »

The "V's" of the last bellows fold slip over the two open ends of the U shape of the rig, with the rest of the bellows (and the opposite end to which you want to work on) hanging down free below. The reedblock can be affixed into the other end and then placed on top of the open bellows and held there by hand. The free hand then can work the bellows up and down to sound the reeds.
May sound a bit problematic, but you soon become adept at it.
Good luck!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Do you have to use a tuning table?
« Reply #9 on: September 14, 2022, 09:45:21 PM »

Thanks for all the pictures!
I am not following it completely though... how do you use this bellow setup? Do you basically tune the reeds in the instrument, but just mount the box on top as opposed to worrying about the bellow pins?


Here are a few pics to show to show you how this works. The instrument for which this board was made is very heavy, hence the wooden cheeks at the ends to stop the board bending under the weight of a big Club box. I have five boards cut out like this to fit a variety of boxes. The slot is cut out to fit snugly into the valley of the first bellow fold.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Do you have to use a tuning table?
« Reply #10 on: September 14, 2022, 09:51:42 PM »

This shows the bellows fitted into the frame. The treble end is being tuned here so the bass end is still attached to the bottom of the bellows. The treble end is fitted on top to sound the reed you are tuning. I always block the holes where the bellows pins go through with tape or Blutack to minimise leakage.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Do you have to use a tuning table?
« Reply #11 on: September 14, 2022, 09:56:31 PM »

It can be a bit of a faff blocking off ports you don't want to sound or lose air through, especially when you remove some blocks in order to leave yourself enough room to work on the reeds you are tuning.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Do you have to use a tuning table?
« Reply #12 on: September 14, 2022, 10:10:41 PM »

You will need to buy or make a few special tools and learn how to use them in order to do a reasonable job of tuning. I really would recommend that you buy an old junker PA or similar and practice on reeds you can afford to ruin. There is an art to this and however practical you are it will still take some time to acquire the skills, make the inevitable mistakes and tune your eyes and ears to the intricacies of reed work. I've been at it a few years now and I still have a lot to learn!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Do you have to use a tuning table?
« Reply #13 on: September 14, 2022, 10:18:20 PM »

I have to say, I don’t bother with a U frame. You can sit the box on a table and lift the end on and off the bellows and lift it up and down, by gripping the first fold and the side of the casing with one hand, and operate a key with the other.. That’s how I fine tune bigger accordions. The Bugari tuner I saw in Castelfidardo just lifted the end on and off a set of bellows fitted with a big open aperture and wide leather pad as in my photo. I couldn’t get on with the U shaped frame favoured by you guys…it seemed more complicated that it needed to be. But that’s just me…

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Do you have to use a tuning table?
« Reply #14 on: September 14, 2022, 10:37:17 PM »

I have to say, I don’t bother with a U frame. You can sit the box on a table and lift the end on and off the bellows and lift it up and down, by gripping the first fold and the side of the casing with one hand, and operate a key with the other.. That’s how I fine tune bigger accordions. The Bugari tuner I saw in Castelfidardo just lifted the end on and off a set of bellows fitted with a big open aperture and wide leather pad as in my photo. I couldn’t get on with the U shaped frame favoured by you guys…it seemed more complicated that it needed to be. But that’s just me…


I can only speak for myself, I'm an amateur and you're a pro, I find it difficult to hold an accordion end down tightly on a flat surface, press the appropriate key and lift a board attached to a bellows at the same time so I just do what works for me. If I remember correctly, I pinched the idea from Lester who I think was inspired by another fettler/maker. This probably works better on lightweight boxes rather than five voice 120 bass PAs.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Do you have to use a tuning table?
« Reply #15 on: September 14, 2022, 11:00:04 PM »

The U frame Obvs works well…but not for me..

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Do you have to use a tuning table?
« Reply #16 on: September 14, 2022, 11:05:06 PM »

It can be a bit of a faff blocking off ports you don't want to sound or lose air through, especially when you remove some blocks in order to leave yourself enough room to work on the reeds you are tuning.

Removing done blocks will alter the pitch of adjacent reeds which defeats the purpose of tuning in the box!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Do you have to use a tuning table?
« Reply #17 on: September 14, 2022, 11:28:13 PM »

Ouch, another lesson learned then. Ta (I think), the plot thickens!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Do you have to use a tuning table?
« Reply #18 on: September 15, 2022, 02:33:57 AM »

Removing done blocks will alter the pitch of adjacent reeds which defeats the purpose of tuning in the box!

So... basically just tune the reeds in place?


I am not quite to that step yet. I was hoping to tune individual reed plates now until I get the new valves placed, and then wax to the block. I guess I am doing it all wrong then :P
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Do you have to use a tuning table?
« Reply #19 on: September 15, 2022, 08:32:10 AM »

Fitting valves changes the pitch,  fitting to the reed block changes the pitch.  If you have an old German instrument where the reference pitch was A=435 you can take the pitch up to approximately 440,  but it’s only approximate.  You could call it pre-tuning.  Final tuning has to be done with the Reed’s on the blocks and the blocks in the instrument.  Otherwise it’s only approximate tuning.

Tuning is like any other craft.  It takes many hours of practice to develop your skills.  Tuning reeds off the blocks is a good place to start,  but it’s a lengthy learning process.  I still have the first box I tuned.  Now I know it is pretty terrible, but at the time it represented an achievement along the learning path. At the time I thought it was pretty good.   I keep it as a reminder to myself that I may not be as good as I think I am!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal