Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reeds not holding tuning  (Read 1592 times)

0 Members and 1 Guest are viewing this topic.

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Reeds not holding tuning
« on: December 16, 2022, 10:19:14 PM »

I’ve been doing some minor maintenance on a recently-built québécois melodeon. Two on pitch middle register reeds seem to be immune to holding their tuning. I’ve replaced wax around them, re-valved them, and even swapped in replacement reeds of the same make/quality. Perplexed! Anyone have any thoughts?
Logged
Too many accordions, help!

Gonk

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 507
  • (Mudlark Music)
    • Mudlark Music
Re: Reeds not holding tuning
« Reply #1 on: December 16, 2022, 10:48:17 PM »

Sometimes it's the reed tongue rivet.  If you put it on a hard surface and tap it (not hard) with a hammer, it can re-stabilize the reed.

Odd that it happened with replacement reeds, too, though.
Logged
Mudlark Music - restoration, repairs, lessons, and sales.  (USA)  http://mudlark-music.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds not holding tuning
« Reply #2 on: December 16, 2022, 11:28:08 PM »

I’ve heard a number of people who have had reed rivets that needed to be tightened.  I can honestly say that in nearly 29 years working as a tuner that I’ve never encountered this problem.

If the problem remains when you swap reeds it suggest that the cause is something else, not the reed. I have had similar problems very occasionally that on investigation turned out to be caused by tiny air leaks between reed chambers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Reeds not holding tuning
« Reply #3 on: December 17, 2022, 03:59:14 AM »

I’ve heard a number of people who have had reed rivets that needed to be tightened.  I can honestly say that in nearly 29 years working as a tuner that I’ve never encountered this problem.

I find that very surprising. I’ve only been doing this a handful of years, and I’ve come across them quite a number of times! They buzz and rattle (and the tongues are perfectly aligned in their slot) and only re-tightening the rivet in a vice does the trick.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds not holding tuning
« Reply #4 on: December 17, 2022, 09:03:14 AM »

Getting back on topic if it’s two adjacent reeds then any air leak is likely between those two chambers.  If the fondo is plywood it can be a defect in one of the ply’s.  If it’s an aluminium fondo with registers it can be a gap between the layers.  It can also be a gap in the glue line in wood joints.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tony Peri

  • REEDWORKS
  • Member
  • *
  • Offline Offline
  • Posts: 13
  • Professional Accordion Tuner/Repairer
    • Accordion Tuning & Repairs | Castagnari Accordions in Australia
Re: Reeds not holding tuning
« Reply #5 on: February 23, 2023, 10:40:22 AM »

Hello,
It could be the pallet is not lifting high enough when you press the button, in effect choking the note. I suggest this as you have the same problem after replacing the reeds with others, but the pitch is still changing. Otherwise if you think it is the reed, put some curvature in the last third of the reed and the pitch will hold better.
Good luck,
Tony
Logged
Accordion Repairs, Tuning | Castagnari Accordions in Australia

Hohner Morino C/F Club N; Scandalli C/F & Various 2 row Hohners.

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reeds not holding tuning
« Reply #6 on: February 23, 2023, 10:51:26 AM »

"curvature in the last third of the reed"

Mmmmm, very interesting! Could you give us some sort of visual aid to help the numbskulls amongst us (me, really!)?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reeds not holding tuning
« Reply #7 on: February 23, 2023, 12:06:20 PM »

I've no idea what your melodeon looks like, but make sure your blocks sit tight and, if this is not the case already, connect them with a brace.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reeds not holding tuning
« Reply #8 on: February 25, 2023, 06:02:43 PM »

Try a brace between the reed blocks. You my be having a harmonics issue where the mass of the reed block is a factor of the problem reeds frequency.
I run into this on smaller instruments.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reeds not holding tuning
« Reply #9 on: February 25, 2023, 06:17:49 PM »

I've no idea what your melodeon looks like, but make sure your blocks sit tight and, if this is not the case already, connect them with a brace.


Try a brace between the reed blocks. You my be having a harmonics issue where the mass of the reed block is a factor of the problem reeds frequency.
I run into this on smaller instruments.

I’m not positive but I believe this is a one row 4 stopper. So only one block standing.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reeds not holding tuning
« Reply #10 on: February 26, 2023, 06:37:59 AM »

A four stop would have two blocks, with two sets of reeds per a block.
If the blocks are removable  check to see if they are warped.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reeds not holding tuning
« Reply #11 on: February 26, 2023, 08:51:40 AM »

Most Quebec built 4 stops have a single upright reed block with two banks or reeds and on either side another bank of reeds laid flat.  The blocks are usually glued in place.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Reeds not holding tuning
« Reply #12 on: February 26, 2023, 05:13:12 PM »

Here is a video demonstrating the rivet tightening improvement in one instance. The pertinent portion is 4:52-6:47.

Clear elimination of wandering pitch by using a nail-set on the rivet. Hohner reeds.

https://youtu.be/0ZFedfsZPJg?t=292

Scott
Logged
too many boxes...please buy one, or two, or

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reeds not holding tuning
« Reply #13 on: February 26, 2023, 06:15:26 PM »

Here is a video demonstrating the rivet tightening improvement in one instance. The pertinent portion is 4:52-6:47.

Clear elimination of wandering pitch by using a nail-set on the rivet. Hohner reeds.

https://youtu.be/0ZFedfsZPJg?t=292

Scott
Good video Scott! But it won’t help Ryan in this case as he has tried other reeds and that doesn’t fix the problem, so as it has already been said — a good tap on the reed and or some brace on the reed banks is not the answer.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reeds not holding tuning
« Reply #14 on: February 27, 2023, 05:03:04 PM »

Most Quebec built 4 stops have a single upright reed block with two banks or reeds and on either side another bank of reeds laid flat.  The blocks are usually glued in place.

Ah yes, then a brace would not be the answer then.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Reeds not holding tuning
« Reply #15 on: February 27, 2023, 06:55:10 PM »

I found on a similar box there was a section around the middle of the reed mounting above the slide that wasn't glued properly. That certainly made the tuning unstable.
Sorry can't describe it better but you can probably work out what I'm saying.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reeds not holding tuning
« Reply #16 on: February 27, 2023, 07:16:00 PM »

Quote
Quote from: theo on Yesterday at 08:51:40 AM
Most Quebec built 4 stops have a single upright reed block with two banks or reeds and on either side another bank of reeds laid flat.  The blocks are usually glued in place.

Ah yes, then a brace would not be the answer then.

A few Quebec makers build boxes with the side banks angled, see pictures of 2 here http://forum.melodeon.net/index.php/topic,25777.msg306893.html#msg306893. One of the two has braces, suggesting braces can be useful with this design.  Interesting to note the picture of the unbraced box was posted by Komat, so who knows, this -could- be the problem box we're discussing here. Pure speculation...

(btw, thread was started over 2 months ago so hopefully the problem has long been solved) 
Logged

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: Reeds not holding tuning
« Reply #17 on: February 28, 2023, 05:40:00 PM »

The box in question has blocks on either side of an upright block in the middle, but angled and not laid flat. The two side blocks are supported by pieces of hardwood against their back. Pallets have plenty of lift across all holes. All blocks are glued in firmly. Bracing might yield a positive response, I’ll report back.
Logged
Too many accordions, help!

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reeds not holding tuning
« Reply #18 on: February 28, 2023, 06:49:09 PM »

Ah, not at all what I was thinking. So a brace or two may help then.
Or maybe a couple more buttress blocks?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal