Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Re-purposing PA reeds  (Read 1916 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re-purposing PA reeds
« on: December 26, 2022, 10:33:24 PM »

I just wanted to encourage anybody who is thinking of re-purposing PA reeds.  It's not as hard as it sounds. It’s time consuming but it’s pretty straight forward to do. Try it …. It’s great for developing tuning technique  (:)

It’s the first time I’ve tried it and it works well.

I had an old Dedenis C/B box which was Ok but the reeds were not brilliant.  It’s now fitted with a D/G treble set taken from a 1920’s "La Sirena Loreto" 43 key 4 voice 120 bass piano accordion that cost me £25.  These have been changed from unisonoric to bisonoric. Coupled with the changes in key the Dedenis treble now sounds a whole lot better and sports one of the most responsive set of reeds I have (the reeds have much finer reed/plate gaps than I’ve seen before)……... and……. I still have loads of reeds spare (620+ donor reeds taken in total).

A few key points re the process that may be of interest:

1. Don't get attached to the piano accordion ..... it was hard to let it go.
2. Strip all the reeds de-valve and fully clean.  I used a lot of acetone and a series of brass bristle brushes - fully clean and mark up well. Use racks.
3. Map the target notes/frequencies well and document well
4. Check the fit in the blocks. The PA reeds tend to be longer. I had to make some reed mounts longer by cutting away the block.
5. Use donor reed plates that "split the difference" re the target bisonoric frequencies I.e Tune one reed up and one down.
6. Rough tune each clean selected donor reed plate using a good file to within 10 cents of target by pinging +10 -10 depending on reed. It does not take long once you are used to it. File flat to achieve good reed profile with support.
7. Re-valve. I used plastic thin ones to make subsequent fine filing easy.
8. Take the reeds to a fraction of 1 cent of target erring positive using a diamond file 160 grit tuned on the block (no wax). Support over valve. File flat to improve profile.
9. Wax. I actually progressively wax the offset MM+ pairs, recheck cents, scratch and balance beats using pure Hz offset. I do this for each pair progressively low to high.
10. Once all waxed I balance beats again by scratching.
11. Box up and use for a week.
12. Refine tuning (on block) to suit “boxed” requirements (perceived required offsets).

This is my first conversion of a box using repurposed PA reeds.   It’s time consuming but it’s worth it. …… and you “own” every reed😀

BTW …. I’m still working on the bass side.

Hope this is of interest.  I have learnt a lot from this site (thanks). It’s a brilliant resource and source of inspiration.

John
« Last Edit: December 26, 2022, 10:51:09 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Re-purposing PA reeds
« Reply #1 on: December 30, 2022, 08:14:07 PM »

Thanks for sharing your process. I'm considering doing this with some old Paolo Soprani PAs I have lying around. Will still have to find diatonic reeds for the lowest and highest reeds since the pitch differences are too great.
I have noticed that on some old diatonic boxes the scale length of each reed is mostly equal for the press and draw reeds with the exception of the very high notes. Makes me wonder if they repurposed PA reeds in the factory for these diatonic boxes. Mostly noticed this in Frontalini diatonics.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Re-purposing PA reeds
« Reply #2 on: December 30, 2022, 09:04:37 PM »

Here is a set of repurposed pa reeds.
Most have been filed up and down a semitone and the low reeds just weighted with lead solder.
This is the H set (minus the top two) and the L set.
M and M+ are in the acetone pot.
These are for a 4 stop in Bb I'm making up from an old C/C# box.
« Last Edit: December 30, 2022, 10:49:36 PM by Squeaky Pete »
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: Re-purposing PA reeds
« Reply #3 on: December 30, 2022, 09:40:59 PM »

Thanks for sharing your process. I'm considering doing this with some old Paolo Soprani PAs I have lying around. Will still have to find diatonic reeds for the lowest and highest reeds since the pitch differences are too great.
I have noticed that on some old diatonic boxes the scale length of each reed is mostly equal for the press and draw reeds with the exception of the very high notes. Makes me wonder if they repurposed PA reeds in the factory for these diatonic boxes. Mostly noticed this in Frontalini diatonics.

One of my solutions to ex-PA reeds, for those with too great a difference to simply re-tune,  is to carefully razor-saw one of each of the target reeds from its partner, lap the edges on an emery block to flatten, and then superglue them together. I have some I did years ago which have seen good service, and not one has come apart. If you use a fine enough saw, both reeds remain useable.
Dave.
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Re-purposing PA reeds
« Reply #4 on: December 30, 2022, 10:15:35 PM »

PA reeds can be made into diatonic reeds even for those that have 'too far a spread' without having to resort to drastic measures.  Lower reeds need only a bit of solder, and higher reeds can be flattened by quite a bit more than the average reed due to there being a lot of material to work with at the base of the reed (thank to Theo for this tip - I used to use a *tiny* amount of solder, filed down to nearly nothing, on the tips of higher reeds to make up the difference.  It worked very well, but was time consuming and finnicky, and Theo's suggestion works very well without any perceivable drawbacks).
Logged
C#/D player

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: Re-purposing PA reeds
« Reply #5 on: December 30, 2022, 10:57:11 PM »

PA reeds can be made into diatonic reeds even for those that have 'too far a spread' without having to resort to drastic measures.  Lower reeds need only a bit of solder, and higher reeds can be flattened by quite a bit more than the average reed due to there being a lot of material to work with at the base of the reed (thank to Theo for this tip - I used to use a *tiny* amount of solder, filed down to nearly nothing, on the tips of higher reeds to make up the difference.  It worked very well, but was time consuming and finnicky, and Theo's suggestion works very well without any perceivable drawbacks).
Indeed, and this is what I do now. Just wanted to share an option I tried in the past, whilst experimenting. It did work surprisingly well though!
D.
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Re-purposing PA reeds
« Reply #6 on: December 31, 2022, 02:44:27 AM »

Thanks for sharing your process. I'm considering doing this with some old Paolo Soprani PAs I have lying around. Will still have to find diatonic reeds for the lowest and highest reeds since the pitch differences are too great.
I have noticed that on some old diatonic boxes the scale length of each reed is mostly equal for the press and draw reeds with the exception of the very high notes. Makes me wonder if they repurposed PA reeds in the factory for these diatonic boxes. Mostly noticed this in Frontalini diatonics.

One of my solutions to ex-PA reeds, for those with too great a difference to simply re-tune,  is to carefully razor-saw one of each of the target reeds from its partner, lap the edges on an emery block to flatten, and then superglue them together. I have some I did years ago which have seen good service, and not one has come apart. If you use a fine enough saw, both reeds remain useable.
Dave.

Nice solution and I'll probably try this at some point. I don't think i'd do this to a box that i'd be selling on though.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Re-purposing PA reeds
« Reply #7 on: January 13, 2023, 10:08:02 AM »

When you made your 4 stop, what did you make the slides from and do you have any pictures please.
I would like to make a Cajun type one row and i have a old set of Hohner double ray BC reeds that I may be able to recycle.
Possible?
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Re-purposing PA reeds
« Reply #8 on: January 13, 2023, 04:08:09 PM »

Thanks for replies/interest.  The whole process is now complete (completed this morning) so I just thought I would post the video of me hitting random keys to see what it sounds like having just boxed it up at last. Thought it might be of interest.

The one thing I also wanted to mention is that in doing this I have realised how robust reeds actually are.  I had none that didn't work. Filing was quick to get close to target and as long as you are fastidious re cleanliness and be-burring they just pretty much work.  I did have to clean edges using a .0015 feeler gauge and fine emery at times but as long as you sight the reed gaps carefully and ensure the reed aperture is clean the reed will sound cleanly.

Thanks for reading. As I say this is a great forum and without the wealth of knowledge shared here I would not have done this ..... thanks  (:)


Click on image below for video and sound of the modified reeds (NB it still needs balance tuning .... and somebody that can play it  :D) :

These reeds are 100 years old:


IMG_0437 by John Burks, on Flickr

Also a picture my left over reeds below ...... If a reed plays up you have spares  ;D
« Last Edit: January 13, 2023, 06:21:48 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Re-purposing PA reeds
« Reply #9 on: January 13, 2023, 06:32:18 PM »

When you made your 4 stop, what did you make the slides from and do you have any pictures please.
I would like to make a Cajun type one row and i have an old set of Hohner double ray BC reeds that I may  be able to recycle.
Possible?

The slides on the PA I just stripped were brass in their own slot on the bottom of the block.  They were still perfectly serviceable after their long life. From memory they were about 1mm thick.  I suspect though that you can buy sheet and guillotine strip and then drill and file.

Hope this helps.  I suspect others here have done it though and can advise.

Might try it myself eventually :D
« Last Edit: January 13, 2023, 06:37:49 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Re-purposing PA reeds
« Reply #10 on: January 13, 2023, 06:37:49 PM »

I make my stop slides from 1.5mm aircraft plywood.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Re-purposing PA reeds
« Reply #11 on: January 13, 2023, 08:22:57 PM »

I make my stop slides from 1.5mm aircraft plywood.
Thanks Rees.
I will do same as I make model aeroplanes and have plenty of 1.5mm birch ply.
The information I have !!!!!!!! Ahem!!!! Was not clear on which material was used for the slides.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Re-purposing PA reeds
« Reply #12 on: January 13, 2023, 08:31:19 PM »

I have made slides from 1mm Clear Thin PETG Plastic Sheet

HERE

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Re-purposing PA reeds
« Reply #13 on: January 13, 2023, 11:07:57 PM »

I'm surprised that wood is used for slide material, at least in cases where reedblocks are glued down.  The reason I don't think this is a good idea is that I've seen several cases where slides had snapped off inside the box because the instrument had been accidentally dropped/banged into and there had been impact to the stops that connect to the slides.  It doesn't take much, and depending on where the slides break, there is sometimes no way to repair them.  Metal slides will not break like this, nor would other forms of plastic.  Even Hohner uses metal slides.  I know most one-row builders have chosen to build them out of wood, probably because it's easier than cutting out holes in metal/plastic (and also easy to match the thickness of the wooden ply used to divide the blocks and create room for the slides), but unless you can remove the reedblocks, I think it's far from an ideal choice.

(Apologies for continuing the thread drift)
« Last Edit: January 13, 2023, 11:09:37 PM by mselic »
Logged
C#/D player
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal