Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed Scratchers  (Read 1776 times)

0 Members and 1 Guest are viewing this topic.

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Reed Scratchers
« on: January 12, 2023, 09:58:24 PM »

G'day.
I have received some reed scratchers from Charlie.
The tips are round in section.
Are these to be further shaped ie honed to an ideal shape and if so whats best?
I am at a loss to know how to sharpen them.
Cheers
Peter
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed Scratchers
« Reply #1 on: January 12, 2023, 10:20:15 PM »

They should be flat on the end so you have a circular scarping edge all round.  In use the tip needs to be sharpened periodically to keep it cutting easily. You need a fine flat very hard abrasive for this.  I use either a smooth arkansas stone, or a 600 grit flat diamond file.  Lay the stone on the bench and hold the scratcher vertical.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Reed Scratchers
« Reply #2 on: January 13, 2023, 03:38:14 AM »

They should be flat on the end so you have a circular scarping edge all round.  In use the tip needs to be sharpened periodically to keep it cutting easily. You need a fine flat very hard abrasive for this.  I use either a smooth arkansas stone, or a 600 grit flat diamond file.  Lay the stone on the bench and hold the scratcher vertical.
Okay Theo.
Thanks for that.
I will give it a sharpening session.
Pete
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed Scratchers
« Reply #3 on: January 13, 2023, 09:11:32 AM »

They should be flat on the end so you have a circular scarping edge all round.  In use the tip needs to be sharpened periodically to keep it cutting easily. You need a fine flat very hard abrasive for this.  I use either a smooth arkansas stone, or a 600 grit flat diamond file.  Lay the stone on the bench and hold the scratcher vertical.
When that is done, the burr needs to be removed by holding the scratcher horizontal and rolling its tip gently on the stone.
Logged

Chris Harris

  • Member
  • *
  • Offline Offline
  • Posts: 36
    • The Bush Inn, A Proper Pub!
Re: Reed Scratchers
« Reply #4 on: January 13, 2023, 09:36:09 AM »

From the answers given would it be easy to make a scratcher from a HSS drill bit, "sharpening" the chuck end as described and using insulation tape the other end to fashion a handle? If so what diameter drill or drills are suitable? Thanks in advance.
« Last Edit: January 13, 2023, 10:01:45 AM by Chris Harris »
Logged
I have a 4th button start Dino Baffetti Black Pearl III, tuned to Anahata layout. I have a 23 button D/G with fourth button start that apart from no badge, looks like a Sandpiper Dunlin III, already converted to Anahata layout.
I was looking for a G/C box because I like French tunes and I was tempted by an almost new Hohner Pokerwork for 500 euros at a large music store in Normandy. However I saw a Lorenzy on Facebook Marketplace and I spent a lovely morning driving into Swiss Normandy and bought it. I love it, it was cheap (392 euros new), out of tune (from new I think) but lovely to play!

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Reed Scratchers
« Reply #5 on: January 13, 2023, 09:50:46 AM »

@ Diatonics thank you I will do that.
But would'nt the burr help to get a good scratch?
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Scratchers
« Reply #6 on: January 13, 2023, 09:57:19 AM »

Chris, there are any amount of ways to produce your own scratcher. As the forum cheapskate, I've tried quite a few!
As for drill size, if you're going down that route, as long as it fits through the slot it should be OK. Drills tend to snap under pressure, though, so be careful!
The same goes for redundant needle files. It seems that the harder your scratcher is, the easier it breaks.
Eventually, I've bought a scraper/scratcher from Mr Marshall, and that is what I use mostly. I sharpen it occasionally with a diamond file using the method which Theo described above.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Chris Harris

  • Member
  • *
  • Offline Offline
  • Posts: 36
    • The Bush Inn, A Proper Pub!
Re: Reed Scratchers
« Reply #7 on: January 13, 2023, 10:12:48 AM »

Chris, there are any amount of ways to produce your own scratcher. As the forum cheapskate........

Thanks Winston. In your self appointed post have you made do with other home made tools that you can recommend for tuning?
Logged
I have a 4th button start Dino Baffetti Black Pearl III, tuned to Anahata layout. I have a 23 button D/G with fourth button start that apart from no badge, looks like a Sandpiper Dunlin III, already converted to Anahata layout.
I was looking for a G/C box because I like French tunes and I was tempted by an almost new Hohner Pokerwork for 500 euros at a large music store in Normandy. However I saw a Lorenzy on Facebook Marketplace and I spent a lovely morning driving into Swiss Normandy and bought it. I love it, it was cheap (392 euros new), out of tune (from new I think) but lovely to play!

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Scratchers
« Reply #8 on: January 13, 2023, 11:14:26 AM »

Nothing special, sorry. I use old feeler gauges for reed supports and for checking and cleaning the clearance between the reed tongues and plates, and glue bits of emery tape to lolly sticks to file down solder weighted reeds, 'cause it clogs proper files which then have to be cleaned with the soldering iron; what a clart on!
As for files, I expect that it's false economy, but I tend to use cheap, locally sourced, needle files or smallish files from car boot sales (often found in the bottom of an old tool box, but new nevertheless!). 
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Chris Harris

  • Member
  • *
  • Offline Offline
  • Posts: 36
    • The Bush Inn, A Proper Pub!
Re: Reed Scratchers
« Reply #9 on: January 13, 2023, 12:09:02 PM »

Thanks Winston.
Logged
I have a 4th button start Dino Baffetti Black Pearl III, tuned to Anahata layout. I have a 23 button D/G with fourth button start that apart from no badge, looks like a Sandpiper Dunlin III, already converted to Anahata layout.
I was looking for a G/C box because I like French tunes and I was tempted by an almost new Hohner Pokerwork for 500 euros at a large music store in Normandy. However I saw a Lorenzy on Facebook Marketplace and I spent a lovely morning driving into Swiss Normandy and bought it. I love it, it was cheap (392 euros new), out of tune (from new I think) but lovely to play!

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Reed Scratchers
« Reply #10 on: January 13, 2023, 01:42:11 PM »

@ Diatonics thank you I will do that.
But would'nt the burr help to get a good scratch?


No just the opposite, you need a very square edge to scratch as you push (mostly) or pull (occasionally) the tool along the reed tongue at a steep angle. I think you may be confusing this with the kind of burr that you would put on the edge of a cabinet scraper.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Reed Scratchers
« Reply #11 on: January 13, 2023, 08:31:51 PM »

@ Diatonics thank you I will do that.
But would'nt the burr help to get a good scratch?


No just the opposite, you need a very square edge to scratch as you push (mostly) or pull (occasionally) the tool along the reed tongue at a steep angle. I think you may be confusing this with the kind of burr that you would put on the edge of a cabinet scraper.
You are correct as I have sharpened cabinet scrapers and it is crucial that its done correctly with a burr.
Thats why I raised the question here as it is also vital to have a scratcher correctly sharpened and at the right shape.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed Scratchers
« Reply #12 on: January 13, 2023, 09:28:09 PM »



[/quote]
You are correct as I have sharpened cabinet scrapers and it is crucial that its done correctly with a burr.
Thats why I raised the question here as it is also vital to have a scratcher correctly sharpened and at the right shape.
[/quote]

In my line of work (making diatonic accordions) I use cabinet scrapers (made from accordion reed steel) almost daily. Actually, I prefer these too with a square edge. Not only do I get a perfect result also without a burr, but the constant filing and burnishing in the end ruins the scraper.
« Last Edit: January 13, 2023, 09:32:17 PM by diatonix »
Logged

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Reed Scratchers
« Reply #13 on: January 14, 2023, 04:14:28 AM »



You are correct as I have sharpened cabinet scrapers and it is crucial that its done correctly with a burr.
Thats why I raised the question here as it is also vital to have a scratcher correctly sharpened and at the right shape.
[/quote]

In my line of work (making diatonic accordions) I use cabinet scrapers (made from accordion reed steel) almost daily. Actually, I prefer these too with a square edge. Not only do I get a perfect result also without a burr, but the constant filing and burnishing in the end ruins the scraper.
[/quote]
That is a reversal of what I have been taught and practiced however if it works for you hats off.
I was taught that the burr was essential in order to scrape good thin shavings like a plane.
Yes it takes time but has worked for me.
How does it ruin the scraper?
I am curious?
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed Scratchers
« Reply #14 on: January 21, 2023, 09:35:34 PM »





[/quote]
That is a reversal of what I have been taught and practiced however if it works for you hats off.
I was taught that the burr was essential in order to scrape good thin shavings like a plane.
[/quote]

Shavings from a square-edged cabinet scraper
Logged

odonovanchris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 276
    • Instagram Accordion Profile: chris0donovan
Re: Reed Scratchers
« Reply #15 on: January 21, 2023, 10:28:48 PM »

My go-to scratcher is a tungsten carbide rod. You can buy them cheap off amazon. 1, 2 and 3mm rods are useful for different sized reeds. Very sharp and they hardly ever wear out. Can be sharpened with diamond grit. I put them in a wooden handle.
Logged
See my accordion projects on Instagram: https://www.instagram.com/chris0donovan/

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: Reed Scratchers
« Reply #16 on: January 29, 2023, 11:54:52 AM »

If you don't have a diamond file you could use sanding paper on a flat surface, for instance a glass table top.
I use fine waterproof sandpaper and I sharpen the scraper by keeping it perpendicular to the surface and making circles.
The first 'scraper' I bought was the same as show in a tool kit here: https://accordion-doctor.com/product/accordion-reed-tuning-tools/
Is it just me, or is this a very lousy scraper? the metal is so thin it bends. I never used it for scraping because I couldn't make even the tiniest scratch on a reed with it.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Scratchers
« Reply #17 on: January 29, 2023, 12:17:46 PM »

After clarting about with broken files and the like for quite a few years, I eventually managed to persuade myself to buy a scratcher, like the one you show, from Mr Marshall.
I went for the thinnest one, so that I could use it on the smallest reeds. I've found it to be fine, but it needs constant attention to the edge to work at its best.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Willem Feltkamp

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 129
  • Tinkering and playing diatonics and CBA
Re: Reed Scratchers
« Reply #18 on: January 29, 2023, 01:34:20 PM »

So they do work! here's a pic of my scrapers. I use the thin one for reed lifting (reeds outside the box) only
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Scratchers
« Reply #19 on: January 29, 2023, 02:13:53 PM »

To be honest, I've used all sorts of things to scratch away a reeds!
As long as it's harder than the reed metal and you don't go at it too hard, or accidentally take some of the reedplate off at the same time, you shouldn't do any permanent damage. 
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal