Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Old Paolo - removing reeds from blocks - tips for marking? keeping sorted?  (Read 1227 times)

0 Members and 1 Guest are viewing this topic.

Chris Deis

  • Member
  • *
  • Offline Offline
  • Posts: 16

I expect to start removing the reeds from their blocks soon for cleaning. I've already marked the blocks in pencil to know what reeds go where, and my thought is to mark each reed plate so I can easily keep track of them, and score a \ on the upper right indicating "outside" of the reed. I'm afraid marking with sharpie will disappear after ultrasound cleaning in acetone, so thinking an engraver might be the ticket.

Is that a reasonable plan? Appreciate knowing what is best practice here.
« Last Edit: April 08, 2023, 11:00:29 PM by Chris Deis »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place

I’ve never marked reeds, apart from the diagonal “this side up” on a corner.  But that is usually there from the factory.  I’ve made a lot of light wooden trays that are long enough to take the reeds from one block laid out in two rows.  If I’m making up a set I lay a strip of paper on the tray first and write the note names on the paper.  That’s all that’s necessary.  If you do feel the need to write on reed blocks please do it on a strip of masking tape that you can remove later.  Look at the way the blocks are before you  start, you   won’t find note names anywhere from the factory, or from well trained repairers. It’s just unnecessary. 
When I fit a set of reeds to a block I’ll tack them in place with a couple of drops of wax.  Then sound the reeds on a test bellows to confirm they are correctly placed before final waxing.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Deis

  • Member
  • *
  • Offline Offline
  • Posts: 16

Thanks Theo for the sage advice. I was thinking I'd lose track of their order when cleaning them in the acetone, but probably necessary caution on my part.

Cheers!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place

As long as you keep each bank of reeds (from one side of a block) separate the size of the reed plates gives you a handy check that they are in the right order.  Just have to be careful if there is an accidental at the start of the row.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants

It’s normally possible to tell which is the outside of a plate because of the wax stain near the rivet…where there isn’t one on the inside. You can ping them to get the pitch. And you can hear the sharp/flat difference just by pinging. And pretty much everyone can hear this. I often test this with customers when I demonstrate how easy it is to identify the reeds… and they can always hear the difference, even when the reeds are only a few cents apart.

Chris Deis

  • Member
  • *
  • Offline Offline
  • Posts: 16

Thanks Rog! That makes perfect sense. I was over-thinking it as usual.  : )
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal