Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Possible Misaligned Reed  (Read 1570 times)

0 Members and 1 Guest are viewing this topic.

Spimbly

  • Member
  • *
  • Offline Offline
  • Posts: 12
Possible Misaligned Reed
« on: April 18, 2023, 01:17:28 PM »

I've recently taken possession of a GC pokerwork, the low C on the C row of which sounds like a distressed goose. I've had a look inside, and it seems a little like the reed is overlapping the edge of its hole in the reed plate - is there anything I can practically do about this or should I just send it off to a tuner/repairer and make it their problem?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Possible Misaligned Reed
« Reply #1 on: April 18, 2023, 01:51:13 PM »

If the reed is actually overlapping the edge of the hole then I would expect it to make no sound at all.

If you press on the reed tongue will it move down into the slot?  If so you might hear a scraping noise as the tongue makes contact.  If that’s the case the next thing is to be sure which edge is making contact.  Then you can try nudging the reed across into the correct position.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Possible Misaligned Reed
« Reply #2 on: April 18, 2023, 06:56:02 PM »

Nudging reeds can be done with the blade of a feeler gauge. Sometimes it takes a few goes.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Possible Misaligned Reed
« Reply #3 on: April 18, 2023, 08:08:11 PM »

Sometimes there can also be something of a ‘burr’ left on the edge of the reed tongue (from tuning, for example)… not necessarily anything visible to the naked eye, but very gently passing the file across the edge of the reed tongue can clean up anything that’s essentially protruding and getting in the way of a clean passage of the tongue in its opening.
Logged
C#/D player

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Possible Misaligned Reed
« Reply #4 on: April 18, 2023, 08:21:24 PM »

If your first attempt is less than successful, I would suggest popping the reed plate out of the wax, removing the inner valve, then, when you hold the plate up to the light its easy to see the clearance all around the reed.
It can then be adjusted, cleaned etc. and then a new valve fitted.
The rivet may also need tightening with a couple of taps also.
Logged

Spimbly

  • Member
  • *
  • Offline Offline
  • Posts: 12
Re: Possible Misaligned Reed
« Reply #5 on: April 22, 2023, 12:45:32 PM »

Turns out it overlaps by less than half a mm, to my (wildly inaccurate) eye. No luck nudging it sideways so far, but I have some [that tool whose name I've forgotten, flat pieces of metal for measuring small gaps] in the shed so I'll try nudging with those in a slightly more organised fashion layer.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Possible Misaligned Reed
« Reply #6 on: April 22, 2023, 08:23:10 PM »

Don't nudge too close to the tip of the reed as it could bend. Try and get the feeler gauge back along the reed towards the rivet. Then nudge gently.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Possible Misaligned Reed
« Reply #7 on: April 23, 2023, 01:16:21 PM »

For info. only - if you decide to shave 1mm or so off the rivet end of a reed plate, its tempting to use a belt sander - this generates heat V.QUICKLY.
This heat OFTEN has the effect of loosening the grip of the rivet on the reed, which then can go out of alignment.... Not recommended treatment for your "Sunday Best" reeds then.  Practice on spare reeds if poss.
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Possible Misaligned Reed
« Reply #8 on: April 23, 2023, 07:43:11 PM »

I made a video of my backlit reed testing fixture that shows the nudging process at time: 7:30 to center a rubbing reed. The link starts part way through where I discuss this particular 3D printed fixture. It allows the reed to be tuned (blow or suck) while the inspection backlight is on.

https://youtu.be/Om-_EmoCcwM?t=270

Later in the video there was a reed needing tip filing to stop rubbing as shown here:

https://youtu.be/Om-_EmoCcwM?t=550

Scott
« Last Edit: April 23, 2023, 07:51:14 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Possible Misaligned Reed
« Reply #9 on: April 24, 2023, 08:38:30 AM »

It’s not difficult to realign a reed. You don’t need any fancy gadgets. Remove reed from the block and remove the valve. Use a bright light. Use some tuning bellows to test your reed laid flat.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal