Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Fitting new bellows help please  (Read 3181 times)

0 Members and 1 Guest are viewing this topic.

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Fitting new bellows help please
« on: April 26, 2023, 10:01:53 PM »

My bellows pins are quite slack in the outer casing.
Do I glue plugs into the holes and re drill?
Also, when drilling the new holes through to a new set of bellows, do I firstly apply just hand pressure to the whole closed carcass or has it got to be somehow clamped together?
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Fitting new bellows help please
« Reply #1 on: April 27, 2023, 11:03:20 PM »

Thin superglue and wood dust is a good fix for loose bellows pins. Just poke it in the hole and let it dry.

I've heard of several ways to drill through for new bellows:
1. Without bellows gasket - use hand pressure only.
2. With bellows gasket fitted - clamp using medium pressure.
     There may well be other ideas ...........
« Last Edit: April 27, 2023, 11:17:52 PM by rees »
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Fitting new bellows help please
« Reply #2 on: April 28, 2023, 07:08:15 AM »

Thin superglue and wood dust is a good fix for loose bellows pins. Just poke it in the hole and let it dry.

I've heard of several ways to drill through for new bellows:
1. Without bellows gasket - use hand pressure only.
2. With bellows gasket fitted - clamp using medium pressure.
     There may well be other ideas ...........

Thank you Rees.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Fitting new bellows help please
« Reply #3 on: April 29, 2023, 09:36:13 AM »

To drill holes: Do it without gaskets and use pieces of leather or cardboard about 0.5 mm thick instead. Fast, comfortable and accurate. Fit one pin after drilling the first hole (more often than not the frame moves inside the casing).
« Last Edit: April 29, 2023, 09:41:30 AM by diatonix »
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Fitting new bellows help please
« Reply #4 on: April 29, 2023, 12:03:21 PM »

To drill holes: Do it without gaskets and use pieces of leather or cardboard about 0.5 mm thick instead. Fast, comfortable and accurate. Fit one pin after drilling the first hole (more often than not the frame moves inside the casing).

There you go Peter. I had thought about using this method too. It's about halfway between the two methods that I mentioned and is probably the best one to use.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Fitting new bellows help please
« Reply #5 on: April 29, 2023, 12:16:07 PM »

Yes that’s the best method,

Another refinement, which will depend a bit on what wood you use.  It can be worth using a slightly underside drill eg 2.4mm for 2.5 mm pins.  This will ensure that you get a good fit where the pin won’t fall out.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Fitting new bellows help please
« Reply #6 on: April 29, 2023, 02:20:29 PM »

Good point Theo - point, geddit?
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Fitting new bellows help please
« Reply #7 on: April 29, 2023, 02:27:13 PM »

Har! Har!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Fitting new bellows help please
« Reply #8 on: April 30, 2023, 08:44:39 AM »

I think Emmanuel Pariselle had a jig or some sort to drill the holes…in Yeovil in 2014. He may do it differently now. Can anyone remember?

Peter Cane

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 204
Re: Fitting new bellows help please
« Reply #9 on: April 30, 2023, 10:35:18 AM »

To drill holes: Do it without gaskets and use pieces of leather or cardboard about 0.5 mm thick instead. Fast, comfortable and accurate. Fit one pin after drilling the first hole (more often than not the frame moves inside the casing).
Diatonix...you are in!!!! We all agree with you!!!!
Seriously though...thank you.
Now you mention the process it makes good sense using card as a stop gap and then when the gasket is fitted the pins will be a nice tight fit and compress the gasket.
Theo and Rees also great thanks.
I get the bit about using a smaller drill bit!...to keep the pins tight..

Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Fitting new bellows help please
« Reply #10 on: May 16, 2023, 01:25:46 PM »

Hi All,

A related question: I am fitting new frames & bellows to a new body.
My plan so far is to:

Clamp each frame to the body halves, using a piece of 0.5mm veneer as spacers, drill the shell and the frame in one go for pins.
Glue the frames onto the bellows, then glue gasket on frames.

Does this sound like a reasonable approach?

Can you please let me know what glue will do the job of sticking the wooden frames to the bellows?

Thank you.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Fitting new bellows help please
« Reply #11 on: May 16, 2023, 01:41:53 PM »

Sounds ok. Again I'd use PVA bookbinding glue. Don't forget that the bellows is considerably thicker in its corners. That's why I always fasten clamps all the way round the frame. In this case you need to protect the inside of the first fold with a strip of thin plywood, cardboard or any other suitable material. Others put strips of cardboard in the 4 middle folds to compensate for the lacking millimeters.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Fitting new bellows help please
« Reply #12 on: May 16, 2023, 03:10:31 PM »

Thank you - I've cut up some cardboard, but it seems to work better if I stuff it in the first folds (i.e. right under the ones that I want to glue) rather than the middle.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Fitting new bellows help please
« Reply #13 on: May 28, 2023, 10:15:47 AM »

I ran into a problem folks: I've got 2.0mm pins.
If I drill with a 2mm bit (in reality it's a ~1.9) then the pins are an extremely tight fit. If I move up to a nominal 2.2 bit (in reality, ~2.1) then the pin just drops into the hole with no resistance at all.

Any thoughts (apart from buying a new 2.0mm reamer, as I've managed to lose the old one :-[)

Also, I've ruined one pin hole, but I am hoping that dropping some CA into it will cure the problem. Unless there's better solutions to this problem?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Fitting new bellows help please
« Reply #14 on: May 28, 2023, 11:24:37 AM »

I find the reverse - 2mm drill ends up with a loose fit!  The pin should be a firm fit.  As it goes in it will compress the wood fibres so it should be tight first time.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Fitting new bellows help please
« Reply #15 on: May 31, 2023, 11:52:15 AM »

I guess "2mm" covers anything between 1.9-2.1mm these days...

Any possible solutions to the problem?
I've ordered the reamer, which will hopefully solve the issue, but if not, I'll be back with more questions  >:E
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Fitting new bellows help please
« Reply #16 on: May 31, 2023, 12:14:48 PM »

If the hole is oversize or just a bit loose a drop of boiling water will often cure the problem.
This and judicious use of weak PVA would be my approach.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Fitting new bellows help please
« Reply #17 on: May 31, 2023, 12:32:16 PM »

I agree with Squeeky Pete. CA glue can be difficult to control,esp
the watery stuff-it tends to go places you dont want.
I usually glue in a bit of coctail stick with PVA and re-drill.
If you make sure the stick is level with the top of the hole it will save you having to sand it down later.
Ive not needed to do this very often- I usually just find thicker pins.🙂
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Fitting new bellows help please
« Reply #18 on: May 31, 2023, 02:36:41 PM »

Quote
I guess "2mm" covers anything between 1.9-2.1mm these days...

Maybe that's a bit (pun intended) of an exageration.  For instance, in the 'number gauge' drill bit range there are 4 sizes available within 1.9-2.1, namely 1.93, 1.994, 2.057, 2.083.  https://en.wikipedia.org/wiki/Drill_bit_sizes
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Fitting new bellows help please
« Reply #19 on: May 31, 2023, 03:14:15 PM »

Dang, I was out by 0.03mm.
Eye sight ain't as good as it used to be.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal