Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: P Wyper Patent - 2 Stop - Restoration  (Read 2880 times)

0 Members and 1 Guest are viewing this topic.

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: P Wyper Patent - 2 Stop - Restoration
« Reply #20 on: July 20, 2023, 11:32:47 PM »

Assuming the box was put together with hide glue, after scraping/chiseling away most of the damaged wood you can make pads of rolled/folded paper towels, soak these in hot or boiling water, squeeze gently to remove exess water, place on the part to remove and wait 10-15 minutes.  Repeat applications may be necessary.  In doubt use less water than too much and see how it goes.  In time it will soften glue and make removal fairly easy without harming the fondo: a light scraping to remove most of the glue, clean up with a damp rag and voilà.

 
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: P Wyper Patent - 2 Stop - Restoration
« Reply #21 on: July 21, 2023, 08:33:06 AM »

Assuming the box was put together with hide glue, after scraping/chiseling away most of the damaged wood you can make pads of rolled/folded paper towels, soak these in hot or boiling water, squeeze gently to remove exess water, place on the part to remove and wait 10-15 minutes.  Repeat applications may be necessary.  In doubt use less water than too much and see how it goes.  In time it will soften glue and make removal fairly easy without harming the fondo: a light scraping to remove most of the glue, clean up with a damp rag and voilà.

 
Same principle, but I put water to it with a paintbrush and heated with a soldering iron....

With a small artist's paint brush I applied a tiny bit of warm  water to the tenon & mortice joint at either end and to sides of the part, then I cut/incised the top edge with a scalpel, opened the cut slightly with a small srewdriver, put wate rinto the cut with the paintbrush and then put a 25W soldering iron to the cut. The damaged wood further softened and opened. More water. More heat and after about 5 minutes it was possible to gentlly pull the tenoned ends out of the mortices without damaging them.

Close up photo - both mortices are undamaged.

Clean up with a damp rag and cloth and making/fitting the replacement headstock is the next job.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: P Wyper Patent - 2 Stop - Restoration
« Reply #22 on: July 21, 2023, 09:37:11 AM »

Well done that man! A 'proper' job.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: P Wyper Patent - 2 Stop - Restoration
« Reply #23 on: July 22, 2023, 11:42:18 AM »

Well done that man! A 'proper' job.

What I think may be of interest to others is applying a point source of heat, together with wetting to soften the glued interface from  INSIDE the part to be removed. Obviously no use if the part to be removed isn't damaged beyond repair already.

Some basic maths/physics ( And a very rough time estimate)

Specific Heat of Water is 4200 Joules/ kilogram/ degree C

So 4200 Joules of Thermal energy will raise 1 kg of water 1 degree centigrade

So 4.2 Joules will raise 1 g of water 1 degree centigrade

1 cubic centimetre of water weighs 1 gramme.

A power rating of 1 Watt = 1 Joule per second.

At a guess I had no more than 1 gramme of water in that rib ( its total volume was no more than 2 cubic centimetres)

25 Watt soldering iron.....estimating 16% efficiency i.e. 4 Watts or 4 Joules per second makes it to the tip of the iron

At that heat input rate the temperature of the water/wood is going to increase by 1 degree per second. 

Roughly 80 seconds of heat to get to glue melting... =/- 50 %

(I think it actually took about a minute but I wasn't clock watching)
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal