Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Soldering Gun versus Soldering Iron for freeing off rusted in screws?  (Read 3373 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039

Does anyone use / Has anyone tried this?

More power from a solder gun... faster heating or did it all go horribly wrong?
Logged

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227

 Just put a screwdriver on the head of the screw and hit it firmly with
a hammer. I've not tried heat. ( on a box).
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions

I've not tried my solder gun for that job but a soldering iron certainly works especially on rusted bellows pins.
I did manage to shear off a very badly rusted Hohner bellows pin yesterday, first time that's happened.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039

The challenge right now is to take apart, rather than destroy, a Dienst International keyboard.

I believe the Dienst split keyboard was at one point a patent design (at least in the German Customs Union) so there is a possibility that an assembly diagram still exists as a public record but I don't know.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403

Quote
The challenge right now is to take apart, rather than destroy, a Dienst International keyboard.

I believe the Dienst split keyboard was at one point a patent design (at least in the German Customs Union) so there is a possibility that an assembly diagram still exists as a public record but I don't know.

Yes, I have a 1-row 2-voice with a Patent Fingerboard.  Outwardly, it's pretty much a typical older 1-row fingerboard with the top section removable and held in place by 2 screws.  I assume one of these 2 screws is causing you problems ?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place

Soldering iron . Can be effective in getting rusted in screws to move. A good load of solder on the iron helps to make thermal contact with the screw head. A sharp tap with a hammer as noted above us also helpful.  Finally don’t just unscrew, but start by turning in the tightening direction then turn  back and forth gradually increasing the distance turned.
Finally make sure your screwdriver is not worn. (Re-grind the tip if necessary) and it must be a good fit in the screw head.
If despite all this the screw breaks off in the wood I have a neat way of getting the bits out.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions

If despite all this the screw breaks off in the wood I have a neat way of getting the bits out.

Now then Theo, you have us intrigued. Spill the beans  ;D
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place

Ok, it’s basically a very simple idea that I originally had from Colin Dipper.   It is to use a very fine steel tube as a core drill to remove a circular plug of wood containing the broken screw.  The tube I use is a blunt hypodermic needle.  These are available on eBay in a variety of sizes. The ones I have vary between 1mm and 2mm diameter.  I remove the socket that would attach to a syringe, then file some notches in the business end. After that it goes in a drill chuck just like any drill bit.  I use a small drill press which give a lot of control but you could do the same with a hand held drill.  Once the piece is removed glue on a plug of similar wood and drill a new pilot hole for the replacement screw.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.

Well done to Mr Dipper!
What's needed in these situations is a little ponderance time, an ounce of ingenuity and half an ounce of confidence.
If all that fails, a decent hammer will fix it properly!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions

Thanks Theo for this week's money saving tip. Great idea.
« Last Edit: June 08, 2023, 12:36:51 AM by rees »
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Soldering Gun versus Soldering Iron for freeing off rusted in screws?
« Reply #10 on: June 07, 2023, 08:55:26 PM »

Oo…trade secret. Nice,

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Soldering Gun versus Soldering Iron for freeing off rusted in screws?
« Reply #11 on: June 07, 2023, 09:12:08 PM »

Thanks Theo for this weeks money saving tip. Great idea.
And chewed up wood and broken twist drill saving. (:)
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Soldering Gun versus Soldering Iron for freeing off rusted in screws?
« Reply #12 on: June 07, 2023, 10:57:57 PM »

Not going well so far.
Trying two different approaches - Take keyboard (complete with wooden action) off: Top screw ( through back of fondo) no problem. Bottom screw absolutely fixed in keyboard. Photo tomorrow.

Quote
The challenge right now is to take apart, rather than destroy, a Dienst International keyboard.

I believe the Dienst split keyboard was at one point a patent design (at least in the German Customs Union) so there is a possibility that an assembly diagram still exists as a public record but I don't know.

Yes, I have a 1-row 2-voice with a Patent Fingerboard.  Outwardly, it's pretty much a typical older 1-row fingerboard with the top section removable and held in place by 2 screws.  I assume one of these 2 screws is causing you problems ?

Yes. and also trying to take keyboard off fondo. Same story: one screw free one fixed.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Soldering Gun versus Soldering Iron for freeing off rusted in screws?
« Reply #13 on: June 07, 2023, 11:00:23 PM »

Thanks Theo for this weeks money saving tip. Great idea.
And chewed up wood and broken twist drill saving. (:)
Hoping so!
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Soldering Gun versus Soldering Iron for freeing off rusted in screws?
« Reply #14 on: June 08, 2023, 10:35:01 PM »

Quote
The challenge right now is to take apart, rather than destroy, a Dienst International keyboard.

I believe the Dienst split keyboard was at one point a patent design (at least in the German Customs Union) so there is a possibility that an assembly diagram still exists as a public record but I don't know.

Yes, I have a 1-row 2-voice with a Patent Fingerboard.  Outwardly, it's pretty much a typical older 1-row fingerboard with the top section removable and held in place by 2 screws.  I assume one of these 2 screws is causing you problems ?

Treble End Photo: The screws holding the keyboard parts together are on the front edge. As previous post also wanting to get the action off the fondo if possible. Sectional keyboaed construction seems to be on all post 1897 (possibly all post 1885) internationals.

I am going to have to set this aside for a few days. Too many other wee jobs needing done (none of them melodeon related) at the same time.

Internally, soldering iron applied to the stuck screw holding the keyboard on released the head from the fondo, but not the threaded part from the body of the key board. More careful regrinding of a screwdriver tip and more heat shock needed before I try again.
« Last Edit: June 08, 2023, 10:42:25 PM by Peadar »
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Soldering Gun versus Soldering Iron for freeing off rusted in screws?
« Reply #15 on: June 22, 2023, 08:41:46 AM »

In the end (for the pallet screws) it came down to holding a 25W soldering iron for a full timed two minutes on the smaller pallet arm screw. When that was done the pallet casing was just too hot to touch. Gave up using a loaded tip after accidentally soldering a screw to the pallet arm  :|bl
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal