Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tjanting (batik) tools for waxing reedplates  (Read 1378 times)

0 Members and 1 Guest are viewing this topic.

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Tjanting (batik) tools for waxing reedplates
« on: June 10, 2023, 09:17:58 PM »

Hello! I have previously had some success using a tjanting tool to wax in reedplates of a Hohner 1040. My method involves putting the tjanting tool in a 130 degree oven along with a jug of wax. When fully melted, the wax is then poored into the bowl of tjanting tool before being applied to the reedblocks…

The only problem when I did this, is that the wax dripped out a little too slowly, maybe 2 times a second… I don’t know what the specs of the tool I used are since it was borrowed. I am therefore wondering  whether anyone else uses this technique and what diameter of spout they find works best, before buying one for myself (they typically come with either 1mm, 1.5mm or 2mm it seems…)

Thanks!
Logged
Dancing about architecture since 1997

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Tjanting (batik) tools for waxing reedplates
« Reply #1 on: June 11, 2023, 02:15:55 AM »

I'm not sure it's the best tool for the job. The wax should flow continuously and not in drops. I think a 2mm hole would be too small to achieve a strong enough flow.
Erm, how do you hold the tool if it's been in the oven? Sounds a bit scary :)
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Tjanting (batik) tools for waxing reedplates
« Reply #2 on: June 11, 2023, 07:51:45 AM »

Haha well, perhaps I should invest in some heatproof gloves?! But for now I just use a cloth to hold it. The wooden handle doesn’t get tooo hot…

What I quite like about the tjanting method is that it is like drawing wax around the reedblocks rather than pouring it in between them. It’s quite neat and tidy when it goes well… I first read about using the tjanting tool when searching about waxing on this forum, so I know I’m not the only one!.. It was somewhat a matter of using whatever tools I could easily (and freely!) get hold of…
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tjanting (batik) tools for waxing reedplates
« Reply #3 on: June 11, 2023, 10:31:36 AM »

What matter is the end result.  How does it look? Are you willing to share a photo?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Tjanting (batik) tools for waxing reedplates
« Reply #4 on: June 11, 2023, 10:58:58 AM »

I’ll see if I can get some pics when I’m back home later. A bit of a disclaimer though… Since the wax was dripping out a little too slowly, it left a few gaps, so I went around the lot with a soldering iron to fill them in, somewhat spoiling the look!..
Logged
Dancing about architecture since 1997

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Tjanting (batik) tools for waxing reedplates
« Reply #5 on: June 11, 2023, 07:04:57 PM »

Here it is, my first and so far only attempt at waxing in reedplates using the tjanting tool!.. As you can see, not great, but not awful. Some of the unevenness is due to having to go over the same patch twice for coverage and using soldering iron to touch in… I’m thinking a wider aperture would resolve this, and if it turns out to be too wide I could perhaps pinch together the opening…
Logged
Dancing about architecture since 1997

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tjanting (batik) tools for waxing reedplates
« Reply #6 on: June 11, 2023, 07:37:33 PM »

That looks ok.  No gaps, and no wax where it shouldn't be, except a tiny dribble on the wood which is easy to scrape off.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Tjanting (batik) tools for waxing reedplates
« Reply #7 on: June 11, 2023, 08:00:31 PM »

Thanks Theo, yes I think it is a method worth persevering with… It’s fairly straightforward, and with the right tool aperture, it ought to take only around a minute to wax in 10 or 11 reedplates on one side of a reedblock (before bringing back up to temperature in the oven for a couple of minutes ready for the other side)…
« Last Edit: June 11, 2023, 08:13:08 PM by Arnold »
Logged
Dancing about architecture since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal