Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Repairing a rough thumb groove  (Read 1323 times)

0 Members and 1 Guest are viewing this topic.

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Repairing a rough thumb groove
« on: July 21, 2023, 11:14:00 AM »

I'm looking for some advice on how to repair the thumb groove on the edge of my keyboard. It looks like a layer of some kind of varnish or lacquer has worn away, leaving a rough texture with a few sharp edges that don't feel very nice under my thumb, I've attached my best attempt at picture but it's quite hard to see in the photo.

To fix it, I'm thinking of sanding it down and then re-applying some kind of finish to the groove, can anyone suggest what sort of product I should use please?

Also, if sanding is the right solution, has anyone got any tips on how to prevent dust getting into the keyboard (or even worse, the reeds)?

Thanks in advance for the help.
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Repairing a rough thumb groove
« Reply #1 on: July 21, 2023, 12:43:48 PM »

Hi
Sanding is the only way to sort that.
If you get masking tape and tape over the buttons and grill there shouldn't be a problem.
If you send me an email with your address I will send you some 400 grit paper,just make a donation to charity.
Re finish with a thinned down varnish,2 or 3 coats
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Re: Repairing a rough thumb groove
« Reply #2 on: July 21, 2023, 03:17:36 PM »

That's a kind offer, thanks Pete. I've got plenty of sandpaper though.

Have you got any suggestions on a specific type of varnish? Will any old wood varnish do the job or is something more specialised needed?
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Repairing a rough thumb groove
« Reply #3 on: July 21, 2023, 08:08:11 PM »

The way it has worn suggests to me that it's a spray finish.
Once you're back to bare wood you can use almost any finish on it.
Sand back to 400 grit as Pete suggested then any of -
A few coats of sanding sealer flatted down after each coat has dried. If you build up slowly you'll get a very good finish.
French polish. This might sound a bit daunting but on a small area that can be coated with just one wipe, it can be very effective (knotting is unrefined French polish)
Acrylic lacquer. Usually can be brushed on with a softish brush. Multiple thin coats better than thick.
Plenty other options too. Others will surely offer suggestions. You could even rub it smooth with your 400 and wax polish it.
All depends on your confidence and skill.
These are all reversible if it all goes wrong
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Repairing a rough thumb groove
« Reply #4 on: July 21, 2023, 11:26:36 PM »

wood looks worn out too, after sanding to good finish, you can use Birchwood Casey Tru-Oil Stock finish, very simple to use but long lasting very strong stuff , apply 4-5 thin coat by your finger  (:)
if you like shiny finish buff it with a cloth or if you like mat finish buff it with steel wool and than cloth..you'll be surprise how good it is once finished.very light amber almost no colour it finishes and you only need a drop or two.         
Logged

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Re: Repairing a rough thumb groove
« Reply #5 on: August 02, 2023, 08:28:33 AM »

Thanks all for the advice. I went for varnish in the end and have ended up with a good finish, hopefully it'll last.
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

Clawhammer

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
Re: Repairing a rough thumb groove
« Reply #6 on: August 02, 2023, 11:07:31 PM »

I do have a Dino Baffetti box without a thumb groove on which I cut and glued a piece of anti-grip kind of stuff available for those with high heel shoes. It's been on there for years.  Thanks,  Bill

https://www.amazon.com/Grips-Protectors-Bottom-Stickers-Covers/dp/B09NLS3GN4/ref=sr_1_10?crid=U4MOKQIWP2TM&keywords=high%2Bheel%2Bgrips%2Banti%2Bslip%2Bbottoms&qid=1691013799&sprefix=high%2Bheel%2Bgrip%2Caps%2C134&sr=8-10&th=1
Logged
trying to capably ride a pair of 2020 Vander Aa and 2025 Fraton 12-bass C Sharp/D boxes.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal