Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Dremel vs. File  (Read 5540 times)

0 Members and 1 Guest are viewing this topic.

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Dremel vs. File
« on: August 11, 2023, 08:38:40 AM »

well, a religious war afaik. But lets go into detail.
I am quite at the beginning of my career as a tuner and obviously the pros does not use "dremels" at all.
I understand that one can ruin a tongue quite easily, but correctly used  powertools may have some advantages.
My attempts with the file were problematic also. Mostly because i found it hard to fix the tongue so it wont move sideways. (and filing can produce an edge that have to be removed so the reed can swing freely)
I did not like the idea of center the tongue gain oftenly, because i am afraid to loose the rivet. Is there a correct way for filing, i mean how to fix the reed and in wich direction to move the file? While filimg i have the "feeler" (sorry no better word for Lösblättchen) under the tongue wich allows the tongue more easily to move sideways.
On the dremel side, i think the kind of attachment (the tool head) is very important. But here i find it critical to not ruin the tip of the tongue, it seems important to hold the dremel in a way the rotation points to the tip direction. I think the goal is to evenly remove of the material, so i use a ball-shaped tip that is not to small. There are common colours, blue and pink, one material is more porous than the other but both are officially not made for hardened steel.
btw way, i am workin on the removed (unwaxed) plates exclusively till now, the idea of filing the "inner" reads scares me, especially the small ones. I am aware that this would not work on a four voiced instrument, but can i get away with this on small boxes? Is it common to tune the reedblocks outside on the table or is a tuning bellow mandatory for finetuning?
I saw a vid were the tuner used fine squared wood sticks sandpaper was glued on. Is this common? A simple (?) question at last: is there a formula where (i.e. 1/3 the reed lenght) exactly material should be removed at the base of the reed? Or if removed at the tip, in wich proportion (width of the filing zone)?

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Dremel vs. File
« Reply #1 on: August 11, 2023, 08:55:56 AM »

Taken as a whole the direction of your questions is asking for a quick way to achieve what can only be truly learned from a long experience, so keep on with the learning process, it takes time to be good at this job.  I don't want to discourage you, but  learning from your mistakes is a powerful way of developing your skill, and you seem to have already made some steps in that direction.

I'll give some quick answer to a few of your practical questions.

Files - if you want to tune successfully with files you need to use the very best quality files.  One of my favourites in traditional files is a Vallorbe triangular needle file, No1 or No 2 cut.  For diamond files a small flat file 600 grit works well for me.  I've tried cheap diamond files and the ones I could find were too coarse and uneven in texture, so again look for the best, not the cheapest.

Reeds rotating on the rivet suggests a combination of poor quality file and less than optimal technique.  Possibly combined with old lower quality reeds.

Final tuning can only be done accurately with the reeds on the blocks and the blocs in situ in the inside the instrument.  You can learn a lot about tuning by working on reeds that are off the blocks, or on the blocks on a test bellows, but the tuning changes when reeds are fixed to a block and when a block is fitted to the instrument.

A sandpaper file like you describe at the end is a very good tool.  Cheap and easy to make and very gentle of the reeds.  Its well worth trying.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Dremel vs. File
« Reply #2 on: August 11, 2023, 06:11:03 PM »

i much appreciate your input. Well, i am getin old and become somewhat patient. Because i am practicing i startet with some quite beat up boxes, but the result is satisfying and keeps me going on. At least I restored a marca four basses and the reeds were extremly rusty. I understand that with pre tuned reeds in a good shape the spot tuning (fine tuning? - tremolo adjustment) can easily be done with a file and scrapper. But extremly lowering or pitch up (say 100 Cents) is much easier and faster with a dremel.
I bought a quality swiss file from Ole (accordion doctor), so that should not be the problem. I know the file is old school and the "right" way, but how much of you guys out there do use the dremel? And if so, can you give me some tips? We are talking melodeons here, right? (not five voiced orchester accordions) I know the pitch is changing if the block is inside or outside the chassis but when measuring the pitch before (inside) and tuning the reeds relatively on the table, the result should be good enough, right?
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Dremel vs. File
« Reply #3 on: August 11, 2023, 06:33:28 PM »

Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Dremel vs. File
« Reply #4 on: August 11, 2023, 06:59:02 PM »

I understand that with pre tuned reeds in a good shape the spot tuning (fine tuning? - tremolo adjustment) can easily be done with a file and scrapper. But extremly lowering or pitch up (say 100 Cents) is much easier and faster with a dremel.
I'm under the impression that, generally speaking, reeds are not meant to be extremely shifted from their original tuning. Not that it can't be done (if you don't have access to similar reeds, or just want a cheap workaround to change notes, salvage old reeds, etc.), but you'd be applying a severe treatment on an overall delicate piece of material, be it with a scraper/file or with a Dremel. Properly set up scrapers/files (ie. of good quality and sharpened regularly) can tune up or down fairly quickly. In both cases, going far from the original pitch can lead to tunings that are not durable, reeds that can break more easily, and a modified timbre.

I know the file is old school and the "right" way
I don't think that it has to do with "old school" or not, neither with a right or wrong issue, and neither is it a religious thing. People are advocating for file/scraper because they are the good tools for the job, as Theo stated earlier. I know that the whole musical instruments profession has a tendency towards conservatism, but I really don't think accordion is the most prone to this trend (and that this doesn't explain the opposition towards the use of Dremel).
From what I understand, the main issue with Dremel is that it'll quickly heat the reed, and therefore modifying its mechanical properties, and in turn its musical abilities. IMO it's also harder to have a precise result, compared to manual tools.

We are talking melodeons here, right? (not five voiced orchester accordions)
Not sure, tuning-wise, that it would change anything :D

I know the pitch is changing if the block is inside or outside the chassis but when measuring the pitch before (inside) and tuning the reeds relatively on the table, the result should be good enough, right?
All is down to what you consider to be good enough ;D. Tuning is arguably the hardest aspect of working on accordions. It is a tedious, meticulous job, and as Theo perfectly said cannot be rushed. When pre-tuning on the table, the discrepancy between the pitch on the table and the pitch on the accordion looks like it depends on the side of the reed plate you're talking, on the size of the bellows that are on your table, on the size of the bellows on your accordion, on the reed block design, etc. I've noticed that experienced tuners that pre-tune their reeds on the table generally know a pitch difference that works with their equipment and can get fairly close to the right pitch this way, but in every case they have to fine-tune it in the accordion.

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Dremel vs. File
« Reply #5 on: August 11, 2023, 07:28:22 PM »

I prefer to lower the pitch by adding a blob of solder to the tip, or add a bit of brass if its a big shift in pitch. Then fine tune with a scraper.
 A diamond burr (especially a new one) can chew off metal in seconds - leaving you see-sawing between the tip and base trying to fix it.
 I have a drawer full of "early attempts at tuning" luckily old donated reeds from old PAs. Dont forget a sticky valve can make a reed sound flat as well.
   There' no substitute for experience. Good luck!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Dremel vs. File
« Reply #6 on: August 11, 2023, 07:32:04 PM »

Regarding tuning by large amounts eg 100 cents or more.  With the right file this is very quick, doesn’t lead to overheating and leaves a nice smooth finish.  Once again a top quality file is essential. 


When tuning this amount you need a good understanding of how reeds are profiled.  That will inform you of which reeds will take that sort of extreme treatment without detriment.  If you don’t understand that you may suffer the problems described in the previous post.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Dremel vs. File
« Reply #7 on: August 11, 2023, 07:37:52 PM »

thanks for the detailed answers. Of course my "dremel" is not a dremel and the rotation speed can be altered, overheatin the reed should be no problem. Its more a question of the right tool-tip. I mean there is maybe no big difference between filing and "dremeling"  :-[ if done right. Do you actually ran into problems because heating a reed?
Really curious about that. Well, i was hoping to came away with not finally fine-tune on the bellow, because i hate angling the inward reeds and scrapp them. My theory is that scrapping does hurt the reed more than filing and waxed on the block the inner reeds cant get filed at the base, right? There is no way to work on a inner reed without bending it out of the plate?
Yes, there is a long way to go i guess, but everyone has to start somewhere. Thanks for your help.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Dremel vs. File
« Reply #8 on: August 11, 2023, 09:27:47 PM »

Dremel seems to be an easy way for beginners to think they can get into tuning. I thought so myself.
I quickly found the methods consistently recommended by the good people here gave better results and caused minimal damage.
A small kit of half a dozen tools, some homemade, will give you excellent results and you will find you do get quicker in short order.
The people I've seen on YouTube who really look like they know what they are doing with a Dremel seem to be vastly experienced and a deep knowledge of how to get results very quickly. I'm talking about very wet tuned Hohner Coronas and similar where an offset of 30 odd cents is required.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Dremel vs. File
« Reply #9 on: August 12, 2023, 09:48:26 AM »

In Thierry Benetoux's book, he recommends filing towards or away from the rivet, rather than across. Or at least directing the file more along the tongue than across it, thus preventing rotation on the rivet. Also you'll be surprised how little downward force you need to apply if you have a sharp file…and a longish file, so you can get a long stroke, if required. And use a v bright light, so you can see exactly what’s going on with the filing. If you bounce the light onto the tongue at an angle it helps to show the cut, esp when you are learning. It’s also worth just filing some metal..any metal… to learn how to use a file. Some of us on here were put through practical training (when we was young …a long time ago) where you spend 6 weeks filing metal (it’s called 'fitting'..the most boring thing you can imagine…filing a chunk of bright steel hour after hour). So it’s a skill to be learned and you don’t necessarily need to he filing reed tongues.

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Dremel vs. File
« Reply #10 on: August 28, 2023, 11:12:10 PM »

ok, no one votes for the dremel. The argument of overheating the reed with a power tool is unreliable in my mind. I heard elsewhere that the reed could be ruined in a way that its harder or impossible to tune them again, but i didnt understand why if the filing process with the dremel is made evenly over the width of the reed. I made my last trials with a 3€ glass engraver stick with one AA battery (not too much uncontrollable power for sure) from the Lidl discounter and must say this tool is nearly perfect for little changes in pitch (up to 10 Cents). I have much respect in traditional handicraft skills, but not for self purpose reasons. I much appreciate any response to my initial question anyway. Maybe this would open another can of worms but in regards to filing the base of the reed, i am wondering if the aspect of lowering the key is: a) to dimish the mass of the reed (filing a bigger aspect of the reed riscing the reed to break) or b) to scratch the reed vertically (prevents the breaking risk) i mean modifiying the movement of the tongue, but i dont really understand the physics behind it, is there material (mass) taken off the reed anyhow while scratching?
Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Dremel vs. File
« Reply #11 on: August 28, 2023, 11:37:35 PM »

I wouldn't say that 10 cents is a small change in pitch. If you take two accordions, one with a 1 cent difference between the two medium voices and another with a 10 cents difference, it will be change the sound *a lot*.
Yes there is matter taken off the reed, either when going up or down, it's the whole point. (For example if I asked you to move up and down a broom handle, by only gripping it by one end, and that I added mass on the other end, you'd be moving it slower)
If you want to go a bit further regarding the physics behind reed movement, you can read basic beam mechanical theory. But it's only a starting point, because we know virtually nothing about the science of free reeds instruments (compared to other instruments).

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Dremel vs. File
« Reply #12 on: August 29, 2023, 03:13:16 PM »

Removing mass towards the reed end makes the tip lighter, therefore more easily swung back and forth by the rest of the blade.  So speed of oscillation (frequency) goes up.

Removing mass in the middle or close to the base of the reed makes the blade more flexible and less springy, so there is less force available to swing the (unchanged) weight towards the tip and oscillation slows down.  In Y's broom handle example, it would be like having a weaker person trying to move the same handle+mass.



Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Dremel vs. File
« Reply #13 on: August 29, 2023, 03:23:15 PM »

ok, no one votes for the dremel.

I will vote for the Dremel :D.   Sort of ....       In my mind there is nothing wrong with Dremel's.  They have their place.  I have just modified some reed blocks to accommodate large reeds and without my trusty Dremel it would have taken ages. 

With regards to reeds though ....

It come down to what tools you use in your Dremel and for what task. I do use a Dremel on reeds but only for specific tasks. 

I have learnt the hard way that you don't touch a reed with a Dremel with anything but a light linishing wheel and this should only be used when fully reprofiling or making a new reed.  Using stones and diamond wheels/burrs on a reed I find to be pretty uncontrollable and there is a tendency to create localised indentations/imperfections that destroy the integrity of the reed. I also suspect that the resultant imperfections/discontinuities increase harmonics depending where they are sited on the reed length. The overall objective should be to keep the cross section of the reed down its length as near a thin rectangle as you can. You vary thickness evenly down its length to control reed flex.  Where the mass is placed (by adjusting thickness) affects stiffness and the overall moment of interia. Getting the overall profile right limits harmonics as the reed then flexes evenly down its length.  In my mind any imperfection down the reed length decreases reed purity.

But...... I admit.....  I reprofile or make bisonoric reeds by linishing using a Dremel (these are usually made from PA reeds but sometimes hand made from strip).   I linish using a rotary tool running down the reed length to base tune. I find that as long as you are careful and you work at lowish speeds you can control the Dremel enough to get a fine flat finish.  Heating is not an issue. Running the Dremel lightly up and down the reed also evens out thickness. In this way you can redistribute the profile without removing much metal. A Micrometer is also handy as it gradually gives you a feel for what metal should be where.  I simply ping to tune.  These "new" reprofiled "bisonoric" reeds are then further tuned by filing with files/diamond files on the bench.  I then scratch/file within the block and casing.  I really don't like over scratching as this can create deep gouges in the base of the reed which can't be good.  Light scratching to really fine tune is fine but not heavy scratching.  I would rather take out the reed plate and use a 600grit diamond file.

So ..... Horses for courses in my mind.  Sometimes the Dremel is right..... most of the time it's not. 

Below are pictures of my "Never use" Dremel tools and my "sometimes use" Dremel tools.  Even the "sometimes " tools required with skill/care and most are used to clean.  The rotary linishing wheel I use is at the top in the picture.

BTW.    I only work on my own boxes. It suits me and I get the box I want.   ;D

John

« Last Edit: August 29, 2023, 10:06:49 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Dremel vs. File
« Reply #14 on: August 29, 2023, 04:56:05 PM »

It is not possible to achieve a satisfactory result with a Dremel. Period.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Dremel vs. File
« Reply #15 on: August 29, 2023, 07:12:12 PM »

It is not possible to achieve a satisfactory result with a Dremel. Period.

Agreed!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Dremel vs. File
« Reply #16 on: August 30, 2023, 07:08:29 PM »

It is not possible to achieve a satisfactory result with a Dremel. Period.

It depends on what “result” you are trying to achieve surely.  If the result is a quick removal of reed material from a reed blank to produce a balanced reed and the mechanical process is controlled and appropriate then all is well.  I am not saying that Dremels have any place in reed tuning but only in roughing out a blank or re-profiling a thick donor reed prior to traditional tuning. All reed manufacturers linish blanks/reeds.  They use band linishers. Some even linish with the reed on the reed plate.  Older high quality reeds I believe were longitudinally linished with rotary linishers.

It’s not easy but with care you can linish without compromising reed integrity. Just my view though.

The problem is the word Dremel has a slightly bad press.  Not unreasonably I suspect.  I have not seen examples but I can imagine the damage!

BTW I don’t have a Dremel … they cost too much … I have a cheap imitation (speed controllable though).

John
« Last Edit: August 30, 2023, 07:10:40 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Dremel vs. File
« Reply #17 on: August 30, 2023, 07:35:02 PM »

Personally I find a file very quick at removing enough metal to repitch a reed by a semitone or occasionally even more. Of course you need high quality files to do this.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Dremel vs. File
« Reply #18 on: September 03, 2023, 02:09:36 PM »

Maybe my file isnt the greatest but perhaps i have some fundamental gaps in knowledge.
As to start i began with some beaten up and very old boxes with rusty reeds, so i wasnt surprised that i had to alter the pitch quite heavily (dremel welcome) When working on single reeds on the table everything is fine, but once waxed on the block work gets harder. Of course i pre tune the reeds as best i can, but particullary the bass reeds differ a little between in-the-box and single on the table. When the reeds are already waxed, but the block is outside the box its quite difficult to modify the "inner" reeds (even more when the blocks are srewed inside the box), I know how to bend the inner reed up from inside the block (or from outside with the angle) and can scratch at the base of the reed to lower the pitch but how the heck should it be possible to file the tip of the reed when bending up (through the plate)??? I avoid this, but with a dremel this should be easier.
As you may guess, i am still a beginner and i understand that fine tuning mint reeds isnt that hard because there is not much material needed to be taken off and my guess is that the inner reeds are prefered pitched down (with the scratcher). Back to topic, my main problem with the file is that the reed-tongue is stressed in a sideward movement, and the slick feeler under the reed makes it even more difficult. Is it safe to state that the file is used exclusively on the outer reeds or on removed plates? My results are very (at least for me) encouraging but i tend to countless de- and install the blocks in the instrument and wax the reeds very sparingly with a brush, to say i more glue them ON in opposite to wax them IN so i can remove single reeds if necessary. That leads me to the last question, do you really need a tuning bellows? I still (want to) believe that its possible to fine tune the blocks on the tuning table.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Dremel vs. File
« Reply #19 on: September 03, 2023, 03:14:14 PM »

Two comments:
If you use files it’s essential that they are sharp and cut easily without needing much force.  Good quality tools always make a job easier. Treat yourself to some good files. 

Second I have no difficulty in filing the inside reeds to raise the pitch while the reeds are waxed (or screwed) onto the blocks, and the blocks are fixed inside the instrument, even bass reeds .  It took me some years to learn how to do this. To begin with it felt awkward and difficult, but with the help of a small number of opportunities to watch experienced tuners at work I developed the skill, and continue to develop it.
Think of it like  learning to play an instrument.  First efforts tend to be clumsy and awkward but with time and practice things improve, then you discover anther new techniques and you go back nearly to the start.  Over the years of repeating this cycle you should gradually get to a time when you find yourself performing fluently, but it’s never the end of the learning g process.
It’s the same with tuning reeds.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal