Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed replacement advice?  (Read 1224 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Reed replacement advice?
« on: August 23, 2023, 08:06:52 PM »

Hi All,

Does anyone have any tips for replacing reeds?

Impulse-bought a 90 year old squeezebox for restoration on evilbay. All's in much better condition that I expected for the age, but two reeds are broken and need to be replaced. A couple more are heavily rusted and might be better off being replaced too.

Any tips on how to do it?
My guess:
1) File the old rivet head
2) Punch/drill out the shank
3) remove old tongue
4) Make a matching replacement tongue
5) Ream the old rivet hole
6) Fit the new tongue and punch the base.
7) Whack it with an 'ammer.

I reckon that I can do it all reasonably well apart from the last bit, which is particularly troublesome: how do I know when to stop whacking the rivet? Is the tongue allowed to rotate at all under strong side pressure after being riveted, or should it be held dead by the rivet?

Any advice (including "Get a life") is welcome.

Thanks.
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Reed replacement advice?
« Reply #1 on: August 24, 2023, 03:46:35 AM »

Replace individual reeds only if it is a long plate model (more than 2 reeds on the plate). Otherwise, just replace the entire reedplate. #4 & #6 are a non-trivial tasks. The rivet can be replaced by a screw and nut. No hammer needed.

https://youtu.be/Wpj3gNohcRc?si=UQ6ykp_oWjM8dYeV&t=78

Scott
Logged
too many boxes...please buy one, or two, or

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reed replacement advice?
« Reply #2 on: August 24, 2023, 06:34:32 AM »

Hi,

Yes, it's the solid solid plank variety.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Reed replacement advice?
« Reply #3 on: August 25, 2023, 08:15:29 AM »

I typically use reeds taken for old hohner reed plates since the rivet typically is the same size. I have had good luck using annealed brass escutcheon pins or sell hardening aluminum aircraft rivets if mild steel rivets are not available.
You should not need to ream the hole.
You do want a snugly fitting (sliding fit) rivet since you will need that as a alignment tool as you file your rivet to fit.

I have had to do this many times for bandoneons.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reed replacement advice?
« Reply #4 on: August 25, 2023, 03:22:42 PM »

Quote
You do want a snugly fitting (sliding fit) rivet since you will need that as a alignment tool as you file your rivet to fit.

Kimric, did you mean 'as you file your reed to fit' ??
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reed replacement advice?
« Reply #5 on: August 25, 2023, 09:11:30 PM »

Bando it is.
Well, another reed broke while I was cleaning it. So 3 to replace.
I've managed to remove the old rivets & reed heels without damaging the plate too much, so I now just have the easy task of making the replacement reeds & riveting them on.

Original rivets are 1.6mm, so I'll need to ream it out to 2mm.

I've decided to have a practice go at a spare chunk of aluminium before hammering the new rivets into the AA plates.

Question about riveting: How do you know when to stop hammering the rivet?
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reed replacement advice?
« Reply #6 on: August 25, 2023, 09:43:37 PM »

Quote
Original rivets are 1.6mm, so I'll need to ream it out to 2mm.

Assumes you have access to 2mm rivets, but 1/16''(1.5875 mm) rivets may fit with no need for reaming...
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed replacement advice?
« Reply #7 on: August 26, 2023, 04:00:08 PM »

Whe hand riveting you don’t just hammer a rivet on the end.  You need a ball peen hammer of an appropriate size for your small rivet. Cut the rivet so the projection is equal to the thickness.  Aim light strikes with the rounded end of the hammer towards the edges of the rivet so that you gradually form a mushroom shape, and continue until the rivet becomes tight.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reed replacement advice?
« Reply #8 on: August 26, 2023, 05:44:12 PM »

This seems to be the Italian way, resulting in a domed "pyramid" rivet.
In Germany and eastern Europe, there seems to be an alternative technique with just flat hammer blows. This bando's got the flat ones.
It's the "until rivet becomes tight" that I don't have a feel for yet, but I'll rivet at least 4 practice tongues before I move on to the real thing.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed replacement advice?
« Reply #9 on: August 26, 2023, 06:57:26 PM »

The German ones with the flat top are clenched by machine, and there are Italian machine made reeds that are similar. The method I’ve described is how my school metalwork teacher taught me to hand clench a rivet.
« Last Edit: August 26, 2023, 07:05:50 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Reed replacement advice?
« Reply #10 on: August 26, 2023, 08:55:35 PM »

Nope, most certainly hand riveted with square heads. There was even a video of a Russian guy making a reed plate and using this method somewhere on youtube.
Old high end bayan reeds and some bando reeds are entirely hand made (slots are hand-filed, tongues are filed to profile with a hand file & hand filed to fit the slot) and they've got flat heads.

I've had a problem forming the pyramid dome, but I guess it's just lack of practice.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal