Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Tuning Question: Removing Material  (Read 1895 times)

0 Members and 1 Guest are viewing this topic.

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Tuning Question: Removing Material
« on: September 04, 2023, 09:49:11 PM »

Hello all, I am starting to tune my CF Pokerwork. I have never tuned before.  At this time, I don’t have a scratcher, but I do have needle files and narrow rifflers that have been trying to use to tune. When scratching the base of the reed (just trying to tune the accidental reeds on the C row), it seems like I need to scratch a lot with the rifflers (they are diamond coated, and rated for metal) to even get a single hertz change. Videos show when people are scratching, they are doing on the order of 5 strokes with the scratcher to bring the reed in tune. My reeds are - pretty much across the board - sharp by a couple hertz.

So, my questions:

1) are scratchers that much more effective at tuning vs other options?
2) how much material do you actually need to remove to change the pitch on say, C3 that is sharp by a couple hertz? Will it be a visible deposition of material? Or just enough to see the scratch marks on the reed?
3) similar to 2, how much force are you applying to remove material? Are you pushing with appreciable force to remove material or are you pretty lite? I understand the higher reeds require less material removal…

I am terrified of ruining my lil’ pokerwork or doing irreparable damage to a reed.  All of the videos and write ups seem to suggest that it is a pretty straight forward process, but to just take it a little bit at a time.

Thanks everyone!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Question: Removing Material
« Reply #1 on: September 04, 2023, 10:03:03 PM »

Tuning is a skill and takes time to learn. You will make the learning process easier and quicker if you get the right tools.
Also get an old wreck to learn on. Then you can learn and make mistakes without being terrified of spoiling good reeds.

It’s not normally necessary to change pitch by as much as 1Hz when doing maintenance tuning. Perhaps you mean cents?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Tuning Question: Removing Material
« Reply #2 on: September 04, 2023, 11:30:50 PM »

If I were you I'd try and spend some time with an experienced skilled tuner. I'm sure that most of us professionals  (who may have tuned thousands of accordions, diatonic and chromatic, during our careers) would happily teach you the basics, including how to make your own tools and how to use them correctly.
« Last Edit: September 04, 2023, 11:42:40 PM by diatonix »
Logged

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Re: Tuning Question: Removing Material
« Reply #3 on: September 05, 2023, 02:40:57 AM »

Tuning is a skill and takes time to learn. You will make the learning process easier and quicker if you get the right tools.
Also get an old wreck to learn on. Then you can learn and make mistakes without being terrified of spoiling good reeds.

It’s not normally necessary to change pitch by as much as 1Hz when doing maintenance tuning. Perhaps you mean cents?

Unfortunately here in the states I haven’t been able to find many wreck accordions that are decently inexpensive that I would be ok “throwing away” - most I have found are $200-$400, not exactly chump change.

The pokerwork was gifted to me from a friend. It was his father’s that he played in the ‘70s-‘90s in a local oompah group. As far has he knows, it has never been tuned.  According to my tuner (a phone app that shows the actual frequency to the 0.01hz), a lot of the reeds are out of tune by a several tenths to 1hz or more in some instances.
Logged

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Re: Tuning Question: Removing Material
« Reply #4 on: September 05, 2023, 02:48:33 AM »

If I were you I'd try and spend some time with an experienced skilled tuner. I'm sure that most of us professionals  (who may have tuned thousands of accordions, diatonic and chromatic, during our careers) would happily teach you the basics, including how to make your own tools and how to use them correctly.

Sitting under a professional - even just being a fly on the wall while they tuned - would be absolutely wonderful. Sadly, here in Ohio, USA there aren’t too many accordion techs. Correction: there aren’t any that I am aware of. The closest one I’ve found is about 6hrs away in Philadelphia (Liberty Bellows).

I would be hugely grateful to anyone here who would be willing to pass on their knowledge and experience!!

Accordionrevival.com has been a wonderful resource - I’ve read through the tuning section more a couple times now - but head knowledge and experience aren’t exactly the same thing…
Logged

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Re: Tuning Question: Removing Material
« Reply #5 on: September 05, 2023, 08:25:19 AM »

Quote
Unfortunately here in the states I haven’t been able to find many wreck accordions that are decently inexpensive that I would be ok “throwing away” - most I have found are $200-$400, not exactly chump change.

You might be able to find a cheap melodica on eBay, even new they aren't particularly expensive but buying a used one will probably give you reeds that are less in tune (and hence have more room for practice). While they're not quite the same type of reeds as in a melodeon, they're still useful to practice on.
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Question: Removing Material
« Reply #6 on: September 05, 2023, 09:02:24 AM »

One of our members here, hickory-wind runs short tuning courses from time to time.  He is based in NY State. It would be worth making contact to see when the next one might be. His website is http://bellingersbuttonboxes.com/
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Tuning Question: Removing Material
« Reply #7 on: September 05, 2023, 09:40:50 AM »

Unfortunately here in the states I haven’t been able to find many wreck accordions that are decently inexpensive that I would be ok “throwing away” - most I have found are $200-$400, not exactly chump change.

I am very cautious of commenting when you are being given advice by experts,but...

I may be wrong, but it doesn't sound like your box is a wreck. Just in need of TLC  (pictures would be nice). It may be worth more than chump change, itself, even as it is,  with untouched original reeds, even CF. Especially if they are fundamentally sound and rust free. These can be a rare asset. You said you were terrified of doing irrepairable damage to the reeds. It's almost certain you will if you try and learn tuning on them.

Have you seen Lester's Hot Rod your Hohner videos?
https://sites.google.com/view/hohnerhotrod




« Last Edit: September 05, 2023, 09:47:02 AM by Tone Dumb Greg »
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Re: Tuning Question: Removing Material
« Reply #8 on: September 05, 2023, 11:38:01 AM »

Unfortunately here in the states I haven’t been able to find many wreck accordions that are decently inexpensive that I would be ok “throwing away” - most I have found are $200-$400, not exactly chump change.

I am very cautious of commenting when you are being given advice by experts,but...

I may be wrong, but it doesn't sound like your box is a wreck. Just in need of TLC  (pictures would be nice). It may be worth more than chump change, itself, even as it is,  with untouched original reeds, even CF. Especially if they are fundamentally sound and rust free. These can be a rare asset. You said you were terrified of doing irrepairable damage to the reeds. It's almost certain you will if you try and learn tuning on them.

Have you seen Lester's Hot Rod your Hohner videos?
https://sites.google.com/view/hohnerhotrod

I have,  it I had been a hot minute! Thanks for the reminder!

The CF I have is in - all things considered - pretty decent condition aside from some cosmetic wear and the aforementioned tuning - which isn’t that and when playing by myself :). The wreck accordions I was referring to are old PAs etc that i have been trying to find up for sale and at garage sales, Craigslist, etc etc.
Logged

Ben

  • Good talker
  • **
  • Offline Offline
  • Posts: 61
  • Hohner G/C, Pokerwork D/G, B/E, Club IIIB S C/F,
Re: Tuning Question: Removing Material
« Reply #9 on: September 05, 2023, 11:40:06 AM »

Quote
Unfortunately here in the states I haven’t been able to find many wreck accordions that are decently inexpensive that I would be ok “throwing away” - most I have found are $200-$400, not exactly chump change.

You might be able to find a cheap melodica on eBay, even new they aren't particularly expensive but buying a used one will probably give you reeds that are less in tune (and hence have more room for practice). While they're not quite the same type of reeds as in a melodeon, they're still useful to practice on.

That, frankly, is a brilliant idea!! Kudos to you, good sir.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Tuning Question: Removing Material
« Reply #10 on: September 05, 2023, 01:28:36 PM »

Quote
Unfortunately here in the states I haven’t been able to find many wreck accordions that are decently inexpensive that I would be ok “throwing away” - most I have found are $200-$400, not exactly chump change.

You might be able to find a cheap melodica on eBay, even new they aren't particularly expensive but buying a used one will probably give you reeds that are less in tune (and hence have more room for practice). While they're not quite the same type of reeds as in a melodeon, they're still useful to practice on.

That, frankly, is a brilliant idea!! Kudos to you, good sir.

I would actually suggest avoiding melodicas in your endeavours to learn to tune an accordion - the only way to get an accurate reading with a melodica is to completely reassemble the entire instrument (including re-fastening all of the screws) after making any changes to a reed.  This process is incredibly time-consuming and inefficient, unlike tuning an accordion where you can quickly place the treble or bass end of an instrument on and off a tuning bellows as you work.
Logged
C#/D player

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Tuning Question: Removing Material
« Reply #11 on: September 05, 2023, 02:04:53 PM »

I would say look out for a real junker.
I just bought a LMM voiced old 120 bass Hohner for about £20 including postage. That's going to yield around 200 reeds to play with.
There was a nicer looking later instrument on marketplace for £25 but collection only about an hour away so I didn't go for it.
But it shows that stuff is around. eBay USA must work in a similar way.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Question: Removing Material
« Reply #12 on: September 05, 2023, 02:15:52 PM »

Also if you use Facebook there is a group called accordion appraisal and sale.  All sorts turn up there from top notch to just the sort of thing you need.  Most posts there are on the USA.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Matthew B

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 894
Re: Tuning Question: Removing Material
« Reply #13 on: September 05, 2023, 02:30:27 PM »

Unfortunately here in the states I haven’t been able to find many wreck accordions that are decently inexpensive that I would be ok “throwing away” - most I have found are $200-$400, not exactly chump change.

Check out the Goodwill online auction here: https://shopgoodwill.com/home.  Search "Accordion".  Current price range is from around $200.00 to around $5.00. 
Logged
Charter Member Presumpscot and Fore River Accordion Club

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning Question: Removing Material
« Reply #14 on: September 06, 2023, 10:10:22 PM »

Scratchers are for very fine tuning inside the box I believe.
For any significant tuning it's better to take the reeds/blocks out and I think that sandpaper is hard to beat. 180-240 grit seems to be just right. Cut it into 4mm-wide strips and work along the entire width of the reed for the outside-mounted reeds. You can shape some ice cream sticks & glue sandpaper to them to be able to fit them into the slots for reeds that are facing inside the chambers.

For raising the pitch, work the top quarter of the reed. For lowering, work the bottom 1/3 of the reed.

The scratcher creates (unnecessarily deep) gouges in the reed and, essentially, damages it, while the sandpaper does not do anything that won't be done to the reed during the standard manufacturing process.
I've happily shifted modern(ish) reeds by 15 cents up & down with no adverse effects, as the amount of material taken off barely went deeper than the factory grinding marks.

The file is very effective, but has a few drawbacks compared to the sandpaper method. It might be very hard to hold the reed in place so you can present it to the file. Also, the file is more aggressive and there's higher chances of missing your pitch and having to work back.
It's very easy to file a new reed with a big three-square file when it's still on the steel strip, but once it's been riveted to the plate, the space is tight and you have to be very careful not to damage the slot edges, filing becomes more of a challenge.

I say avoid the dremel like plague, as there's a lot of scope for damaging the reeds a lot worse than the scratcher.

So, imho:
1) Sandpaper. Easy, effective, least amount of damage.
2) File. Just as good, but harder to use correctly and slightly more scope for damage.
3) Scratcher. Very fine tuning inside the box only.
4) Dremel. Avoid.

The only time sandpaper fails is with the largest unweighted reeds - the material removal becomes just too slow. Either take your time or use the file.
Once you're into the weighted reeds, just use the file on the weight for raising or paper on the bottom 1/3 of the reed for lowering.
« Last Edit: September 06, 2023, 10:22:20 PM by mChavez »
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning Question: Removing Material
« Reply #15 on: September 07, 2023, 12:07:36 AM »

"The scratcher creates (unnecessarily deep) gouges in the reed and, essentially, damages it"

Village idiot here, sorry!
In what respect do the deep scratches 'damage' the reed? And how do you quantify such damage, in that what is the resulting practical effect, evidence or symptoms (performance? early failure?) of such 'damage'?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning Question: Removing Material
« Reply #16 on: September 07, 2023, 06:52:25 AM »

If you scratch, you make, say, a 0.5mm-wide gouge in the reed. If you polish, you remove similar amounts of material over a ~3mm width. Deep gouges are likely to become stress points. And you have less control of how deep you go compared to a gentle sand. I have seen gouges going across reeds  :o as well, which is close to reed murder, as that's where the reeds are going to break.

To increase the pitch, you need to remove the weight from the tip. To exaggerate: If you only made one 0.5mm scratch, it would have to be 6 times deeper than an equivalent sand/file over 3mm. In practice you'd make more than 1 scratch, but you are still gouging the steel much deeper than necessary, and the gouging might end up being on a diagonal rather than along the length of the reed.

For lowering the pitch things are even worse, as you are working on a high stress area. You need to remove stiffness, and a deep gouge along the reed is not going to have as much effect on the pitch as a reed-wide thinning down of the material.
I've read an opinion (quite plausible) that you are also likely be hollowing the reed out by gouging the middle of the reed more than the edges. A hollow-ground reed is likely to perform differently to a flat one.

Mind you, I'm not talking about minor spot tuning, where the difference will be negligible. But I dread to think what will happen to a reed is you need to scratch it >10c down or >10c up (say, after an overhaul & de-rusting, or to adjust musette detuning).

« Last Edit: September 07, 2023, 06:53:58 AM by mChavez »
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning Question: Removing Material
« Reply #17 on: September 07, 2023, 07:13:07 AM »

PS I don't have personal expertise or physics background to argue that one method is much more damaging that the other, but these were the opinions of some tuners on a German squeezebox forum. A while ago there used to be a series of videos by and old-school (& very grumpy >:E) Russian or Ukrainian tuner who used to work for Hohner and he was very critical of the tendencies to over-use the scratcher. The advice was that for anything apart from the most minor pitch adjustments one shall take the reeds out of the box & off the blocks, and work them with a file to avoid unnecessary reed damage and to make sure that the gapping is not upset. His view was that the excessive scratching inside the box and on the reed block is a result of cost/time saving at the expense of the reeds, and that's something he'd never advise doing on a high quality set of reeds.
The videos were taken down a while ago and I really regret not saving them to my hard drive, as there was a wealth of information in a couple dozen "lessons" on box repair.
« Last Edit: September 07, 2023, 07:16:03 AM by mChavez »
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning Question: Removing Material
« Reply #18 on: September 07, 2023, 03:36:59 PM »

More than interesting, thanks you very much.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning Question: Removing Material
« Reply #19 on: September 07, 2023, 03:47:19 PM »

As I said, don't have the metallurgical background to argue whether this point is right or wrong, but one thing I can say is that I have absolutely no problem riding my old Reynolds 531db tubeset after it's been surface sanded for a paint respray, however, if it had deep gouges along, or god forbid, across the tubes, I wouldn't get my butt on it, as the stress concentration points of metals would be very far from my thoughts when my face hits the tarmac at 30mph... Common sense suggests that putting multiple unnecessary deep scratches into a reed will weaken it.
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal