Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Metal Pallets  (Read 2471 times)

0 Members and 1 Guest are viewing this topic.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Metal Pallets
« on: October 01, 2023, 11:39:17 AM »

I think I need a bit of advice.  I was very kindly gifted an old Koch Ouverture a while back which I very much appreciated  (:).  Is a box that I have always wanted to do justice to in terms of making it work again.  It's one of a number that I want to make my own and use on a regular basis.  It's all original with a full set of Koch "Goat" reeds and to date I have stripped the reedblocks, carefully gasketed (I prefer this, if the space is there, to allow very fine tuning/setup), fully cleaned, valved in leather and fine tuned to A440 in the blocks and then in the box.  It's completely dry tuned at the moment i.e. the reeds are matched to within 1 cent.

The problem I have though is the sound/timbre.  It has a "tinny" sort of sound. All notes are perfectly on pitch (beatless and matched) but it just sounds "tinny".  Other boxes I have worked on have a richness that really comes out when you get them set up in this way.  This one just does not sound right. It has a "thinness"  At first I thought it could be the grill which is a thin metal sheet but it's still the same with it off.

It could be the reeds as I have not worked much with these before but when tuning in the blocks they sounded OK to my ear i.e. not as rich as longer PA type reeds but pretty much the same as Hohner.  My current thought now though is the pallets.  It has the Koch metal pallets which are soldered in. 

So a long story .... but my question is:

Is this "tinniness' just a feature of this box i.e. is it an early Koch feature?   and/or
Do the metal pallets contribute to the metallic sound? i.e. is that the tinniness I hear?


I have a vague memory of working on a very cheap PA type keyed melodeon a while back (Tonella?) which had these pallets and from memory it had a similar sound.

The reason I ask is that I will probably reface the pallets and if it helps I may change to wooden.

Thanks.  I just wondered if anybody had come across this before.

 I attach some pictures for info.

Any advice on the best way forward would be much appreciated.  I just want to make it sound richer if I can.

John

« Last Edit: October 01, 2023, 11:49:23 AM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Metal Pallets
« Reply #1 on: October 02, 2023, 09:07:18 AM »

are you able to fit the reeds block into something else than try ?
 some old reeds are quite specially zinc ones. I have Hohner branded Koch boxes with zinc reeds and they are not as loud as my other Hohner, CF Koch I have is very quite compare to similar age CF Hohner zinc reed box , All tuned and set up by same same person but sing differently           
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal Pallets
« Reply #2 on: October 02, 2023, 09:15:50 AM »

Instinct says that having a metal pallet instead of wood is unlikely to affect to sound.

Those old reeds would originally have been tremolo tuned. Have you considered adding in a bit of tremolo?  That would thicken up the sound.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Elizabeth Moran

  • Either that B-word or that C-word
  • Member
  • *
  • Offline Offline
  • Posts: 42
  • Why, yes, I will have some cheese with that whine.
    • Bookface
Re: Metal Pallets
« Reply #3 on: October 02, 2023, 10:14:10 AM »

It's all original with a full set of Koch "Goat" reeds and to date I have stripped the reedblocks, carefully gasketed (I prefer this, if the space is there, to allow very fine tuning/setup), fully cleaned, valved in leather and fine tuned to A440 in the blocks and then in the box.  It's completely dry tuned at the moment i.e. the reeds are matched to within 1 cent.

The problem I have though is the sound/timbre.  It has a "tinny" sort of sound. All notes are perfectly on pitch (beatless and matched) but it just sounds "tinny".  Other boxes I have worked on have a richness that really comes out when you get them set up in this way.  This one just does not sound right. It has a "thinness"  At first I thought it could be the grill which is a thin metal sheet but it's still the same with it off.

Now I know what the goat engravings on the reed plates is about! Thank you. What is the material of the soundboard? I noticed some kind of interesting patterned material behind the pallets. Anything metallic? Are the reed plates aluminum or zinc? The material of the pallets seems inconsequential, but perhaps metal ones might contribute some sympathetic microphonics? Zinc reed plates contribute to the sound vibrations, but I've never heard of pallets having any effect; then again i've never seen metal pallets before.

I like Theo's idea of fattening the tuning differential between the reeds a little bit. One cent is extremely tight. One hertz (1Hz) might give the sound a bit more meat; that's about 4-cents; 2Hz would equal a light demi-swing and still wouldn't add a real beat, just open up the "wah" of the attack. You just wouldn't want to increase or graduate the tremolo much above 10 cents into the upper octave if maintaining a 'beatless' tuning is imperative. How does that sound, Theo? Would that be worth consideration, or is that too weird?
Logged
C#/D Paolo Soprani/Busilacchio MMM
A/Bb Hohner Presswood MM

FS: HoHner Swiss-made Primatona D/D# with Paolo basses with F# push for Finbar Dwyer music.
FS: Paolo Soprani 21/8 LMM B/C 2-coupler, recently revalved, terrific sound.

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Metal Pallets
« Reply #4 on: October 02, 2023, 05:01:59 PM »

Firstly many thanks for all the replies.  They are very much appreciated.  When you are working on your own having input is invaluable as you tend to become a bit fixated on one possibility .

are you able to fit the reeds block into something else than try ?
 some old reeds are quite specially zinc ones. I have Hohner branded Koch boxes with zinc reeds and they are not as loud as my other Hohner, CF Koch I have is very quite compare to similar age CF Hohner zinc reed box , All tuned and set up by same same person but sing differently           

Invadm, many thanks. Your input made me go back and check. I have just spent a hour having a good listen to the reeds inside and outside the box. The Koch ones I have are aluminium and I have just compared to zinc H reeds ... these Koch reeds have a slightly more "tinny" element.  it's noticeable.

Instinct says that having a metal pallet instead of wood is unlikely to affect to sound.

Those old reeds would originally have been tremolo tuned. Have you considered adding in a bit of tremolo?  That would thicken up the sound.

Thanks Theo.  I have also just done a test with the reedblock inside and outside the box there is not much difference. You can hear the tinny element in both so it's not the box/pallets. I also physically checked all of the pallets and they are all sound.  They are not going to vibrate/resonate. 

When I sounded a single reed rather that 2 though outside the box (it may be my imagination) but it sounded better.  So I suspect that I do need to put a slight offset in there. 

I will reface the original metal pallets which I prefer actually as it's in keeping with the box.  I have just found another thread on this process helpful re solder removal and resetting. Thanks.

It's all original with a full set of Koch "Goat" reeds and to date I have stripped the reedblocks, carefully gasketed (I prefer this, if the space is there, to allow very fine tuning/setup), fully cleaned, valved in leather and fine tuned to A440 in the blocks and then in the box.  It's completely dry tuned at the moment i.e. the reeds are matched to within 1 cent.

The problem I have though is the sound/timbre.  It has a "tinny" sort of sound. All notes are perfectly on pitch (beatless and matched) but it just sounds "tinny".  Other boxes I have worked on have a richness that really comes out when you get them set up in this way.  This one just does not sound right. It has a "thinness"  At first I thought it could be the grill which is a thin metal sheet but it's still the same with it off.

Now I know what the goat engravings on the reed plates is about! Thank you. What is the material of the soundboard? I noticed some kind of interesting patterned material behind the pallets. Anything metallic? Are the reed plates aluminum or zinc? The material of the pallets seems inconsequential, but perhaps metal ones might contribute some sympathetic microphonics? Zinc reed plates contribute to the sound vibrations, but I've never heard of pallets having any effect; then again i've never seen metal pallets before.

I like Theo's idea of fattening the tuning differential between the reeds a little bit. One cent is extremely tight. One hertz (1Hz) might give the sound a bit more meat; that's about 4-cents; 2Hz would equal a light demi-swing and still wouldn't add a real beat, just open up the "wah" of the attack. You just wouldn't want to increase or graduate the tremolo much above 10 cents into the upper octave if maintaining a 'beatless' tuning is imperative. How does that sound, Theo? Would that be worth consideration, or is that too weird?

Elizabeth, thanks.  Really good advice  :D. The fondo is wood covered in paper.  I should also have said "Mountain Goat" which is more accurate  (:)  I wondered what it was for quite a while!
I now think the sound a feature of the reeds.  They are aluminium and not as heavy as I'm used too. I also think having them perfectly matched does not help.
I am going to try introducing an offset.  I will try 1Hz (4 cents).  I did read somewhere else that having two reeds perfectly matched is not so good practice so I think that I may have made myself a problem.  I will now map a set of offsets to try to keep the reeds beatless.  Really appreciate your views.  Thanks.  Great advice.

Off to the shed now ......

John

Edit- added photos
« Last Edit: October 02, 2023, 06:06:25 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Metal Pallets
« Reply #5 on: October 03, 2023, 06:02:20 AM »

The reeds in the photo appear to have less taper than, for instance, Hohner reeds; this may have some effect on the sound. But it may just be the result of the camera angle and just an illusion.
That said, I have to agree with previous posts that a bit of tremolo offset would provide a less tinny sound. Reeds tuned to absolute unison will suffer from some degree of acoustic cancellation, the result of which I would certainly describe as "tinny".
Logged
Tuner/repairer, now retired.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal Pallets
« Reply #6 on: October 03, 2023, 07:50:58 AM »

If I were overhauling those reeds I would be using much lighter valves.  Helper springs are usually only needed on the biggest 3 or 4 reeds on each block.  Older reeds like these tend to have a rather thin profile which means they need a wide swing to develop full volume.  My rule of thumb with valves is to try to use the smallest thinnest valves I can get away with.  And even on an old instrument like this I would consider plastic valves on the smallest 4 or 5 on each block, and no valves on the very smallest 1 or 2.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

BoxPlayer

  • Member
  • *
  • Offline Offline
  • Posts: 31
Re: Metal Pallets
« Reply #7 on: October 03, 2023, 12:50:42 PM »

John,
I think Theo's observation on the size of the valves is very relevant. If the valve is not lifting enough the sound will definitely be subdued and choked
not to mention stiff to play.

You also say:  'Thanks Theo.  I have also just done a test with the reedblock inside and outside the box there is not much difference.'
You say there there's little or no difference with the reed blocks in or out of the box. I feel there should be a difference as the housing of the reeds normally adds to the resonance and sound quality. I am immediately reminded of a quality instrument I had which I felt was just not sounding as I thought it should and it was much later I found that the reed-blocks were not sitting tightly against the sounding board. After some attention with sand-paper the contact was much improved and the sound quality was as well.   
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Metal Pallets
« Reply #8 on: October 03, 2023, 06:00:38 PM »

The reeds in the photo appear to have less taper than, for instance, Hohner reeds; this may have some effect on the sound. But it may just be the result of the camera angle and just an illusion.
That said, I have to agree with previous posts that a bit of tremolo offset would provide a less tinny sound. Reeds tuned to absolute unison will suffer from some degree of acoustic cancellation, the result of which I would certainly describe as "tinny".
Thanks Malcolm,  I have just compared and there is less taper. I compared to a similar size Hohner H.  It may be my imagination but the reeds are also thinner/lighter. The overall weight is very different.  On reflection this problem I have might just be a reed feature. I will now pop in a odd Hohner reed and see how this compares (out box/in box)

I do think though that the matched reeds don't help. I isolated one of the pair and it was a purer sound.  I will try an offset .... nothing to loose really!

If I were overhauling those reeds I would be using much lighter valves.  Helper springs are usually only needed on the biggest 3 or 4 reeds on each block.  Older reeds like these tend to have a rather thin profile which means they need a wide swing to develop full volume.  My rule of thumb with valves is to try to use the smallest thinnest valves I can get away with.  And even on an old instrument like this I would consider plastic valves on the smallest 4 or 5 on each block, and no valves on the very smallest 1 or 2.

Thanks Theo,  still learning  (:).   I will change valves. As mentioned above nothing to loose really.  I will also introduce the offset and see what effect it has.

John,
I think Theo's observation on the size of the valves is very relevant. If the valve is not lifting enough the sound will definitely be subdued and choked
not to mention stiff to play.

You also say:  'Thanks Theo.  I have also just done a test with the reedblock inside and outside the box there is not much difference.'
You say there there's little or no difference with the reed blocks in or out of the box. I feel there should be a difference as the housing of the reeds normally adds to the resonance and sound quality. I am immediately reminded of a quality instrument I had which I felt was just not sounding as I thought it should and it was much later I found that the reed-blocks were not sitting tightly against the sounding board. After some attention with sand-paper the contact was much improved and the sound quality was as well.   

Thanks BoxPlayer,  As above re valves ... thanks for input.  (:)  I will also now check the reed block tightness.  I also need to check the box itself again.  My experience is the same as yours. The box usually enhances and this is what I expected. Here it seems to slightly amplify the tinniness if anything and not deepen the sound.   

I now very much suspect that there are two problems .... the valves/reeds are the root cause and the box is not helping  :-\.

All part of the learning process though ....... and perseverance pays off ... usually (:).

Could not progress without this site though ... so thanks all :D

John

« Last Edit: October 03, 2023, 06:08:17 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Metal Pallets
« Reply #9 on: October 03, 2023, 06:07:54 PM »


Thanks Theo,  still learning  (:).   I will change valves. As mentioned above nothing to loose really.  I will also introduce the offset and see what effect it has.


Do one thing at a time so you know how each alters the sound. 

Getting valves right is possibly the trickiest part of setting up reeds.  Too stiff and not enough air gets through and the sound output of the reed is limited, too light and they don't close fully leading to unwanted noises.  Over heavy valves also flatten the pitch, so do the valves first, then the tuning.

You can do a quick check by sounding a reed and then using a probe to lift the valve further,  If there is a marked increase in volume, or change in pitch then the valves are not not optimal.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Metal Pallets
« Reply #10 on: October 03, 2023, 06:11:41 PM »


Thanks Theo,  still learning  (:).   I will change valves. As mentioned above nothing to loose really.  I will also introduce the offset and see what effect it has.


Do one thing at a time so you know how each alters the sound. 

Getting valves right is possibly the trickiest part of setting up reeds.  Too stiff and not enough air gets through and the sound output of the reed is limited, too light and they don't close fully leading to unwanted noises.  Over heavy valves also flatten the pitch, so do the valves first, then the tuning.

You can do a quick check by sounding a reed and then using a probe to lift the valve further,  If there is a marked increase in volume, or change in pitch then the valves are not not optimal.

Thanks Theo,  Great advice ..  Will do. ... a new area for me to try out

Will send email to Charlie tomorrow as valve stock and glue is low  (:)
« Last Edit: October 03, 2023, 06:47:56 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Metal Pallets
« Reply #11 on: October 06, 2023, 03:25:34 PM »

I have now started work to try to clear and I have decided on my stepwise approach.  I did a test first. I took single note  G4 and tested and then changed/adjusted the valves which I think helped.  I then made 1 Hz offset which really did settle the sound. I then tested with and without the grill and with a wooden grill.  This again improved the sound to a point where I am reasonably happy.  During this work I also did notice misalignment of the fondo holes with the reedblocks and on closer inspection found that there was play in the blocks.  The clamping mechanism has built in float for some reason so I need to sort.  I used the oscilloscope function of the tuner during this process and you can see the difference appearing.  The waveform really does stabilise as you deal with these issues.

So on the back of this my plan is as follows:

Strip the box and re face the pallets (it needs to be done)
Reseal the fondo to make sure its sound
Sort the reedblock clamping mechanism
Strip and revalve (not a big job as its gasketed)
Tune with 1Hz offset
Test and adjust valve function
Final tune.
Re think the grill (probably brace the back to reduce vibration.)

Then I will see what I have.

Anyway its started.  The keyboard is off the metal pallets have been stripped and cleaned. and I'm currently cutting the pallet material.

Here are a few photos of my keyboard clamping mechanism, the removed keyboard and the stripped pallets.

Thanks again for all the help.    BTW the metal pallets do need a lot of desoldering. I'm using a 75W iron.

I just thought that I would post this as it might be of use to others with metal pallet boxes. the pallets do come off  ;)

John
« Last Edit: October 06, 2023, 03:30:37 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Metal Pallets
« Reply #12 on: October 06, 2023, 04:31:42 PM »

And don't forget to brace the reedblocks. Either a piece of wire jammed between the blocks or a narrow flat plate screwed to the top of the blocks.
It's amazing how a lack of this can mess with the sound.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Metal Pallets
« Reply #13 on: October 07, 2023, 08:53:18 AM »

I'm with Theo on this. Altering the valves can sometimes have a transformative effect on the sound. And this can be done on a tuning table where you can observe everything. There were plenty of people already commenting….but my first port of call would be to investigate the valves.
« Last Edit: October 07, 2023, 09:29:02 AM by Rog »
Logged

John Burks

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 142
Re: Metal Pallets
« Reply #14 on: October 10, 2023, 07:34:45 PM »

And don't forget to brace the reedblocks. Either a piece of wire jammed between the blocks or a narrow flat plate screwed to the top of the blocks.
It's amazing how a lack of this can mess with the sound.

Hi Squeaky Pete,  many thanks.  It's now on the list. Thanks for reminding me
I will probably anchor between blocks with a metal tie. I also have a problem with the reedblock fit in the "shoe" which I need to sort.  This could also be causing me issues.

I'm with Theo on this. Altering the valves can sometimes have a transformative effect on the sound. And this can be done on a tuning table where you can observe everything. There were plenty of people already commenting….but my first port of call would be to investigate the valves.
Hi Rog,  Thanks for the input. Much appreciated.  I have now fitted new pallet facings and the next job is the valves (I will also sort the reedblock fit while they are off  (:) )
I must admit that I had not realised that the valves could have an effect on the sounding of the reed but it does make sense.  I will do a few tests with the old and new valves to see how they affect the waveform.
I am going to install lighter valves (The ones with the rivet hole) to ensure they sit low on the plate.  Thanks for the input it has helped me focus my mind re the best way forward.  This thread has helped me a lot.  The input really does help  (:)

John
 
« Last Edit: October 10, 2023, 07:38:25 PM by John Burks »
Logged
Francois Dedenis D/G, Koch Overture G/C , Custom "Picoletta" D/G, Hohner Modell 1 B/C, M Hohner 5A B/E (Phosphor Bronze)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal