Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Hohner Corso A/D conversion to C#/D  (Read 4932 times)

0 Members and 1 Guest are viewing this topic.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #20 on: February 11, 2024, 06:46:35 PM »

Hey all,
I’m still working on this ( when I can find time) , I just got the reeds valved and waxed in. Minus a couple.
I ended up using a set of C reeds for the -M row tuning up to close to what I need. I used the F/A# from my C# row ( it had low notes) to make the F#/B for my D row 1st button. And used the 2nd button reed of the A row E/G# to make the D/G reeds I want on the first button of the C# row. I’m still short one reed on C# -M bank which needs to be G#/D#. I may be able to get it from the left over A row.
So after waxing the reeds into the blocks I stuck them in the box to have a listen. The D row as it was not touched ( just cleaned and re- valved ) sounds pretty good and probably needs minimal adjustment.
The C# row is going to need some work on that.

So here’s my goof up, I went to isolate the to pitch banks and taped off the others banks. But when I went to play the D row it was the sharp reeds. So I either marked it wrong or waxed them on the wrong side.  I thought for sure I kept them in the right side.
So how much will it matter and can I leave them or do I need to redo them?

Picture of how I marked them but as said the D block marked S and p ( sharp and pitch) are the wrong way around. Good thing I’m just doing my own boxes  (:)  probably more likely to happen when you’re picking away at a project. Picture taken shows C# reed missing, I didn’t have it valved yet so it is not in yet.

So what is your advice?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner Corso A/D conversion to C#/D
« Reply #21 on: February 11, 2024, 07:05:46 PM »

I don't think it will matter at all but .........
looking at the photo, I think you may have marked them incorrectly in the first place.
The sharp reeds are usually on the same side of both blocks. Yours are marked as being on opposite sides.
So you may have them positioned correctly as it is.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #22 on: February 11, 2024, 07:37:03 PM »

I don't think it will matter at all but .........
looking at the photo, I think you may have marked them incorrectly in the first place.
The sharp reeds are usually on the same side of both blocks. Yours are marked as being on opposite sides.
So you may have them positioned correctly as it is.
Thanks Rees for your thoughts! I’d be glad if I just marked the block wrong, I kept the reeds in order I thought, I had them in a box sitting with the block in between them as I cleaned / valved and re wax doing one reed at a time. So that is a possibility.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner Corso A/D conversion to C#/D
« Reply #23 on: February 11, 2024, 08:03:37 PM »

i have a couple of old Corsos lying about. I'll check when I get a chance.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Hohner Corso A/D conversion to C#/D
« Reply #24 on: February 12, 2024, 01:06:52 AM »

For some reason, I feel like marking them + - 0 is less likely to mess you up! That’s the only notation I use when sorting reed sets, or marking blocks (with a soft pencil).
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Corso A/D conversion to C#/D
« Reply #25 on: February 12, 2024, 08:04:27 AM »

When I need to mark blocks I use masking tape to write on, then remove it when the job is finished, leaving the blocks as I found them. If you put a strip of tape on top along the full length it’s also useful for marking the occasional reed that needs some individual attention.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner Corso A/D conversion to C#/D
« Reply #26 on: February 12, 2024, 10:19:39 AM »

I've just checked inside a Corso.
It's as I thought, the sharp reeds are on the same side of the blocks so yours is probably correct as it is.
Even if they're not it would only be a problem if stop slides were involved.
« Last Edit: February 12, 2024, 10:21:13 AM by rees »
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #27 on: February 12, 2024, 12:50:00 PM »

I've just checked inside a Corso.
It's as I thought, the sharp reeds are on the same side of the blocks so yours is probably correct as it is.
Even if they're not it would only be a problem if stop slides were involved.
Thanks for checking Rees! That’s a relief 😅
For some reason, I feel like marking them + - 0 is less likely to mess you up! That’s the only notation I use when sorting reed sets, or marking blocks (with a soft pencil).

Matt just after I marked them with letters I said to myself why didn’t you use +-0 , which makes more sense. But I don’t think it would have solved this issue, I just need to pay better attention to what I’m doing.
When I need to mark blocks I use masking tape to write on, then remove it when the job is finished, leaving the blocks as I found them. If you put a strip of tape on top along the full length it’s also useful for marking the occasional reed that needs some individual attention.
you are correct I should have used tape and I did when working on the bass / chords. But decided to pencil it in lightly thinking that it could be erased. Next time!


I’m happy that I don’t have to reverse the reeds.
I finished the last reed I needed. I took the C#/G# from the A row to make the G#/D# that I needed to fill in the rest of the C# row.
Thanks again!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Hohner Corso A/D conversion to C#/D
« Reply #28 on: February 12, 2024, 01:49:11 PM »

When I need to mark blocks I use masking tape to write on, then remove it when the job is finished, leaving the blocks as I found them. If you put a strip of tape on top along the full length it’s also useful for marking the occasional reed that needs some individual attention.

I should add that this is also what I usually do with customers’ instruments, but I don’t mind marking “+ - 0” on the blocks of my own instrument directly with soft pencil (which is easily erased if needed).
« Last Edit: February 12, 2024, 01:50:44 PM by mselic »
Logged
C#/D player

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #29 on: March 07, 2024, 03:40:13 PM »

Update: The reeds are in , D row isn’t too far off C# row is going take a little more work, all needing fine tuning. I still need a A/E reed for the broken one, it was fun trying to make one but I’m not happy with it.
I redid the gasket and repaired the small hole in the front ( making it airtight and not cosmetic) , much better now, actually better than any of my boxes. I was planning on replacing the tape on the bellows but I ordered 3/4” and received 1”. I probably won’t get a replacement for the cost of returning would be more than the tape. I did ask though. So I’m not sure if I want the wider tape.
I also limited the button travel. To do so I decided rather than bending the levers out of the way and then having to realign them, that I would knock the wooden supports off with a sharp chisel and then make a set of new pieces. Doing this and sliding them over to the opposite side of the lever. Now the keyboard can come off and on without a problem. A before and after pictured.
I need to touch up the keyboard paint in a couple spots ( or not just call it character) . I think I would have trouble getting a good match for it?
« Last Edit: March 07, 2024, 03:42:03 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hohner Corso A/D conversion to C#/D
« Reply #30 on: March 07, 2024, 03:56:57 PM »

If it is otherwise ok, you could cut the 1" tape to width.  Easy enough (if laborious) using a ruler, cutting wheel and cutting mat.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #31 on: March 07, 2024, 04:52:22 PM »

If it is otherwise ok, you could cut the 1" tape to width.  Easy enough (if laborious) using a ruler, cutting wheel and cutting mat.
It could be done I have the cutting mat / wheel.
Adding more work to an already laborious process as you said, and also I would have to make nice cuts or else. I’m not crazy about using as is , more of an overlay tape I think.
For now I don’t even have to do anything and could use as is for a bit longer. Mostly edge flaking but not completely worn through. Front being the best looking.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #32 on: March 15, 2024, 07:00:48 PM »

I went ahead and cut the tape I have down to 3/4”.
Lucky 🍀 for me the machine / paper cutter I was using to cut the bellow tape to length had a 3/4” metal bar that was slightly recessed from the top. So it was just a matter of holding it up against the lip and down to the table. I had to remove the safety bar and make sure all fingers were clear , worked a charm!
« Last Edit: March 15, 2024, 07:02:34 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #33 on: April 14, 2024, 04:00:51 PM »

Here’s the end result of this conversion.
Don’t mind the sloppy player , it’s going to take time to get used to the inside out system.
The keyboard didn’t need any work other than adding thicker padding behind the buttons and it plays nicely. Feels different than my other Hohners, maybe my imagination?
I want to thank Henry piper for C# reed setup , worked out great!

https://www.youtube.com/watch?v=Z8GnfKJmwXg
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re: Hohner Corso A/D conversion to C#/D
« Reply #34 on: April 15, 2024, 05:24:26 PM »

Here’s the end result of this conversion.
Don’t mind the sloppy player , it’s going to take time to get used to the inside out system.
The keyboard didn’t need any work other than adding thicker padding behind the buttons and it plays nicely. Feels different than my other Hohners, maybe my imagination?
I want to thank Henry piper for C# reed setup , worked out great!

https://www.youtube.com/watch?v=Z8GnfKJmwXg
No problem, glad I was able to help.
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal