Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Hohner Corso A/D conversion to C#/D  (Read 4931 times)

0 Members and 1 Guest are viewing this topic.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Hohner Corso A/D conversion to C#/D
« on: October 08, 2023, 02:10:18 PM »

Hi all,
I recently got the said box. I’m on the hunt for C# reeds , T reeds would match. http://forum.melodeon.net/index.php?topic=29737.0
If you have any PM me please.

Another repair is a broken E chord reed, in the block I’ve got a E4, G#3, B3, and the broken E? I assume E 3 or E 5 , anyone know what it should be?

I’m going to be limiting the buttons, when removing the fingerboard is the treble mechanism going to come out with it or is just the wooden part I want to remove? It looks like it is one piece and or attached, plus the screws holding the fingerboard in look pretty big. Hopefully it is similar to the pokerwork:)

I’ve fixed a loose bass block plate ( re- glued ) and I still need to repair a small hole in one of the valleys of the bellows folds. Beyond that it’s in pretty good shape ( unless I want to get crazy and do the bellow tape;) )
Thanks for any advice or help on this.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Corso A/D conversion to C#/D
« Reply #1 on: October 08, 2023, 06:20:49 PM »

Nice project.

For the missing E reed compare with the voicing of the other chords, and also compare with the push reed on the same reed plate.  It will be less than an octave away.

The fingerboard is two piece, unlike a pokerwork. The red celluloid top comes off first by removing the screws in the top plate.  Then remove the two large screws holding the wooden part and it will lift away to the rear – take care not to dislodge the two wooden supports between the levers, you may have to bend the levers slightly to clear these.

There is felt under the levers which is probably worn or motheaten.  You need a hard grade of felt to avoid a squashy feel to the buttons.   Cushion felt as used on snooker/pool tables is good.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #2 on: October 08, 2023, 07:59:13 PM »

Nice project.

For the missing E reed compare with the voicing of the other chords, and also compare with the push reed on the same reed plate.  It will be less than an octave away.

The fingerboard is two piece, unlike a pokerwork. The red celluloid top comes off first by removing the screws in the top plate.  Then remove the two large screws holding the wooden part and it will lift away to the rear – take care not to dislodge the two wooden supports between the levers, you may have to bend the levers slightly to clear these.

There is felt under the levers which is probably worn or motheaten.  You need a hard grade of felt to avoid a squashy feel to the buttons.   Cushion felt as used on snooker/pool tables is good.
The bass note buttons shares two notes off the chord block ( as you know) , on the broken side I have A4/ E? On the other side of the block is A3/E4. So I assume the broken reed is E5. Just a guess though. I also tried to look a the relationship in the other chord sets but a couple where different.

Thanks for the info on the fingerboard, I had the face plate off the front and just wanted to check to see if the rest of the fingerboard comes out separately / and not with the mechanism. Which your saying it does but with some care on those supports. I will be careful!

I’m in the process of seeing if I could replace the broken reed ( E reed taken from a PA , about the right size but the sides will need a trim to fit ).
« Last Edit: October 08, 2023, 08:01:07 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Hohner Corso A/D conversion to C#/D
« Reply #3 on: October 09, 2023, 04:23:22 PM »

Your broken reed should be A4/E5. At least that’s what I have mapped out on an old Hohner Pre-Corso A/D bass block.
Logged
C#/D player

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #4 on: October 09, 2023, 10:35:16 PM »

Your broken reed should be A4/E5. At least that’s what I have mapped out on an old Hohner Pre-Corso A/D bass block.
thanks again Matt! Please keep your eyes out for a C# set or a wrecked one row or two in that key.
On that note, are there any sites that sell used / repair parts only . I joined a FB site that is supposed to buy sell parts , just be ready to buy the whole thing!!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Hohner Corso A/D conversion to C#/D
« Reply #5 on: October 10, 2023, 03:10:20 AM »

I have a lot of clients asking for A/D to C#/D conversions at the moment, so I’m on the lookout for C# Hohner reeds myself ;)
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Corso A/D conversion to C#/D
« Reply #6 on: October 10, 2023, 09:02:04 AM »

I have some sets of low octave C# reeds.  They are old Hohner stock from the 70s, new and unused.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Hohner Corso A/D conversion to C#/D
« Reply #7 on: October 10, 2023, 09:57:05 AM »

That's an offer which won't come around too often, Theo!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Hohner Corso A/D conversion to C#/D
« Reply #8 on: October 10, 2023, 11:04:30 AM »

I have some sets of low octave C# reeds.  They are old Hohner stock from the 70s, new and unused.
would they give me L-MM voicing if add them to my usual c# reeds set from c/cis pokerwork Theo ?

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Corso A/D conversion to C#/D
« Reply #9 on: October 10, 2023, 11:12:08 AM »

Yes
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #10 on: October 10, 2023, 03:10:15 PM »

I have some sets of low octave C# reeds.  They are old Hohner stock from the 70s, new and unused.
Thanks, but then I’d need some low D sets to go with it and probably some block work involved.
Sounds like just the thing for invadm’s needs though!

I have a lot of clients asking for A/D to C#/D conversions at the moment, so I’m on the lookout for C# Hohner reeds myself ;)
I figured but no harm in asking (:)
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Hohner Corso A/D conversion to C#/D
« Reply #11 on: October 10, 2023, 06:36:08 PM »

yes indeed  (:) I can make 3 or 4 voice single row in C sharp..I play alone so no harm to anyone  >:E
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #12 on: October 14, 2023, 02:28:16 PM »

So finding C# reeds is going to be a challenge I see ( short of buying another box ), so maybe I could use a C or D one row or 2 sets of them to get what I need out of a C or D box? These will fit the in corso block correct?
If so anyone have one / some to sell?
Still on the lookout for C# but throwing more lines in the water to see what else is out there.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hohner Corso A/D conversion to C#/D
« Reply #13 on: October 14, 2023, 02:49:30 PM »

If you're going to source and retune C or D reeds to C#, would it not be just as simple to reuse your A reeds ? (shifted by 1 position they're mostly within 1 semitone of C# target notes)
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Hohner Corso A/D conversion to C#/D
« Reply #14 on: October 14, 2023, 03:10:46 PM »

If you're going to source and retune C or D reeds to C#, would it not be just as simple to reuse your A reeds ? (shifted by 1 position they're mostly within 1 semitone of C# target notes)

That would be the easiest solution and the way I would proceed.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #15 on: October 14, 2023, 03:33:01 PM »

If you're going to source and retune C or D reeds to C#, would it not be just as simple to reuse your A reeds ? (shifted by 1 position they're mostly within 1 semitone of C# target notes)

That would be the easiest solution and the way I would proceed.
Good point Tirpous, I will probably end up going that route.
Thanks to both for your input!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #16 on: October 24, 2023, 12:54:02 AM »

I thought I’d give replacing the broken E reed a go .
Turned out half decent ( first time) . I found a PA E reed ( the E5 on the A/E bass was broken ) that was the right pitch and length but it was too wide, so lots of filing and checking. I had to drill the reed rivet hole to match the hole in the plate, then I loosely set the rivet in the hole and kept checking it when filling.
It’s working good and sounds at - 41 cents F , so a little more adjustment. I guess taking material from the sides of the reed doesn’t change the pitch much. I’m pretty happy it sounds!!
« Last Edit: October 24, 2023, 02:18:08 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #17 on: November 11, 2023, 07:19:10 PM »

Good news! (Well to me anyway) I found a set of C# reeds:) they are making there way to me.
From a C/C# melodeon , T reeds.
So 2 of the MM banks and also being supplied is a C row set  ( mixed H and T reeds possibly? ).
I’m thinking that I could maybe use the C set to make the -M C# set and that the other 2 sets M & +M with some adjusting on all.
Hopefully not much in the way of block work will be needed. It was going to need a filler if I went with using the A row I have. Plus all the adjustment work on the reeds. Finding the missing ones, etc.
I will still need to find 3 reeds for the extra button and possibly a few for the first button.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #18 on: November 14, 2023, 12:31:37 AM »

Anyone know what the bellow gasket size should be on this box?
It’s definitely 5mm wide x ? Thickness . So  2mm or 3mm?
I have some small pieces of each size 2mm&3mm and it seems like 2mm is about right, so I’m looking for some confirmation.
Edit to add: before I order.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner Corso A/D conversion to C#/D
« Reply #19 on: January 07, 2024, 04:56:56 PM »

I went with the 2mm thick gasket, looks about right.
So I’m working on filling in the missing reeds or changing to a new pitch.
I plan on changing the first button C# row to D/G  ( a Paul Groff suggestion ). I’ll need to make or source this reed. My box had accidental notes first button. So I need the low notes on the D row or F#/B, I think I can now take the first button reeds on the C# row and tune them up a semitone as its and F/A#. I just realized this :o . Then lastly I bought a set of C# reeds from a C/C# box so need to fill in the top high notes that are missing. It’s a G#/D# probably a bit of a stretch in both directions to make it from a F# piano reed?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal