Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: button Travel Limiter  (Read 1736 times)

0 Members and 1 Guest are viewing this topic.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
button Travel Limiter
« on: November 06, 2023, 07:34:54 PM »

I've had mixed results with materials used for button travel limiters on early Hohners, mostly Pokerwork style. I'm wondering what the pros use for the wood portion and how thick it should be for these boxes? 1/4" square? also, I think I saw somewhere that a stiff, pool table type felt was suggested for a bit of padding on top of the wood stop.

Any and all help is appreciated
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: button Travel Limiter
« Reply #1 on: November 06, 2023, 08:11:28 PM »

Lots of photos here off how I do it: https://theboxplace.co.uk/2017/11/12/hohner-button-travel-restriction/

I use a softish wood, western red cedar, which has a bit of spring and I quite like the feel without any felt.

The thickness of wood required can vary from one Hohner to another, sometimes the gap tapers along the edge of the keyboards so you need to taper the block to match. The exact thickness is critical to get the buttons to stop in the place where you want.   For me that is slightly below the top surface of the keyboard.  I use digital callipers to measure the space where the stop will go, you could also use simple internal callipers, or even a pair of dividers and a ruler to measure the space.  I cut the wood to the thickness I've measured and do a trial fit, usually find I need to take some off which I do on a belt sander, but you can also use a sheet of abrasive papers stuck onto a flat piece of plywood.  The inside row usually need a slightly lower height which I create by pressing the button so that the lever crushes me fibres and makes a depression in the wood.  If that is not enough the depressions mark the place where you can take off a small amount with the edge of a file.  Go slowly because you don't need to take off much.

When it's all fitting nicely it's ready to fix in place with some small screws.  The strip of wood is quite thin so pilot holes are a must.  Good luck!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: button Travel Limiter
« Reply #2 on: November 07, 2023, 04:30:47 PM »

Thanks Theo, that's very thorough. I forgot about having to deal with the occasional taper. Living on the west coast of Canada you would think that strips of red cedar would be readily available, yet I'm having troubles finding any small dimensional wood in my small town. I need a hobby shop I think.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: button Travel Limiter
« Reply #3 on: November 07, 2023, 04:35:40 PM »

Or a timber merchant or sawmill that will let you have access to their offcuts.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: button Travel Limiter
« Reply #4 on: November 07, 2023, 05:00:59 PM »

Find a cabinet maker, joinery shop, college, craft studio etc and ask to rummage in the offcuts bin. Beer or biscuits is the usual exchange.
I use leather in the same way as Theo uses timber. An upholstery friend lets me dive into his scrap bin for anything useful. It's usually fairly pliable stuff so I start with stiff strips of bagpipe bellows leather and the upholstery offcuts make up the height and give a soft landing.
It took me so long to do this reply that Theo has posted much the same in the meantime.
« Last Edit: November 07, 2023, 05:04:06 PM by Squeaky Pete »
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: button Travel Limiter
« Reply #5 on: November 07, 2023, 10:43:59 PM »

Find a cabinet maker, joinery shop, college, craft studio etc and ask to rummage in the offcuts bin. Beer or biscuits is the usual exchange.
I use leather in the same way as Theo uses timber. An upholstery friend lets me dive into his scrap bin for anything useful. It's usually fairly pliable stuff so I start with stiff strips of bagpipe bellows leather and the upholstery offcuts make up the height and give a soft landing.
It took me so long to do this reply that Theo has posted much the same in the meantime.

Interesting. You don't find the stacked leather and material too squishy?
Logged

fc diato

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 146
Re: button Travel Limiter
« Reply #6 on: November 07, 2023, 11:51:36 PM »

I followed Theo's instructions exactly, but with white pine.  Worked perfectly. Any small scrap of softwood (an old wooden box; a fancy tea box someone gave you years ago that was too nice to throw away; garbage day piles outside houses sometimes yields nice pieces of usable wood; the scrap piles renovators leave in front of a worksite; if you're in a rural area, the dump has old furniture to raid for wood recycling - some of it very nice indeed).
I did try leather at first, but could not figure out how to adjust the different heigths of the 2 rows. In the end, I find Theo's wood solution simplest.
Logged
fc diato

Fionn

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 194
Re: button Travel Limiter
« Reply #7 on: November 08, 2023, 02:03:15 PM »

I don't have room for a workbench, so if I want small / narrow / shaped strips of wood I try the trims and mouldings counter at a DIY store first. They're well machined, there's sometimes a choice between softwood and hardwood, and they come in a whole array of sizes and profiles.
Logged
Vintage Double Ray C#/D

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: button Travel Limiter
« Reply #8 on: November 08, 2023, 03:38:32 PM »

Same here, mouldings from B&Q in the UK.
Pine Stripwood 6mm x 11mm, usually needs and benefits from a felt strip in order to get
the desired button arrest level and to have the right 'feel.'
« Last Edit: November 08, 2023, 03:56:05 PM by gettabettabox »
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: button Travel Limiter
« Reply #9 on: November 08, 2023, 06:16:48 PM »

I was thinking about balsa wood. Not sure if that's something that shows up in the UK but I always remember seeing it at hobby shops varying dimensions. Very soft and easy to work with. I small scroll saw or something similar would sure be handy for cutting the long strips from whatever material I find.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: button Travel Limiter
« Reply #10 on: November 08, 2023, 07:08:15 PM »

I was thinking about balsa wood. Not sure if that's something that shows up in the UK but I always remember seeing it at hobby shops varying dimensions. Very soft and easy to work with. I small scroll saw or something similar would sure be handy for cutting the long strips from whatever material I find.
I've tried using balsa for this job and thought that the end effect was a bit too soft and it wore away rather quickly.

Elizabeth Moran

  • Either that B-word or that C-word
  • Member
  • *
  • Offline Offline
  • Posts: 42
  • Why, yes, I will have some cheese with that whine.
    • Bookface
Re: button Travel Limiter
« Reply #11 on: November 08, 2023, 08:10:14 PM »

Thanks Theo, that's very thorough. I forgot about having to deal with the occasional taper. Living on the west coast of Canada you would think that strips of red cedar would be readily available, yet I'm having troubles finding any small dimensional wood in my small town. I need a hobby shop I think.

i found good pieces of bass, oak, and pine at the local model-making hobby store. Also, a small one-handed trim plane is a nice tool to have, about $15-20.

Then you can always experiment with different hardnesses of foam and felt strips under the button end of the key-levers on the floor of the keyboard, especially if you have rear access to the keyboard cover, like on old Paolos or Acorn or the larger Swiss made Hohner keyboard covers.
Logged
C#/D Paolo Soprani/Busilacchio MMM
A/Bb Hohner Presswood MM

FS: HoHner Swiss-made Primatona D/D# with Paolo basses with F# push for Finbar Dwyer music.
FS: Paolo Soprani 21/8 LMM B/C 2-coupler, recently revalved, terrific sound.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: button Travel Limiter
« Reply #12 on: November 08, 2023, 08:13:14 PM »

I was thinking about balsa wood. Not sure if that's something that shows up in the UK but I always remember seeing it at hobby shops varying dimensions. Very soft and easy to work with. I small scroll saw or something similar would sure be handy for cutting the long strips from whatever material I find.
I've tried using balsa for this job and thought that the end effect was a bit too soft and it wore away rather quickly.

ahhh, that was my worry. i'll try for cedar like Theo suggested. I appreciate you allowing me to learn from your mistakes.  ;D Also, your "hot rod your Hohner" videos have been invaluable over the years for kick starting my restorations.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal