Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Bad reed  (Read 1492 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Bad reed
« on: November 28, 2023, 03:50:46 AM »

I will occasionally come across a reed that has an unstable pitch; it will waver drastically depending on air pressure.  These reeds are not cracked or broken, their valves will be fine (they'll be changed with no difference), the tongues will be perfectly centred in their opening and will move freely with no obstructions in their travel.  Rivets are tightened and plates reinstalled with new wax, etc.  No amount of tinkering with any of the variables seems to correct the problem of unstable pitch (which may waver in the range of 5-15 cents or more!).  The problem will persist on or off blocks.  The only solution I've found in these cases it to just replace the reed.  It's as though it's just a 'bad reed', despite there being no discernable cause.  Has anyone else encountered this problem before and had more insight into what's going on?  To be clear, I'm not talking about big bass reeds that will naturally vary in pitch depending on air pressure.  I'm talking about reeds in the mid-range that would normally be very stable regardless of pressure.  The issue has always just been one reed tongue, never an issue with both tongues on one plate.
Logged
C#/D player

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Bad reed
« Reply #1 on: November 28, 2023, 12:12:35 PM »

"(which may waver in the range of 5-15 cents or more!)."
 
And there was me thinking that this was relatively normal!!! I've spent many hours trying to get reeds to stay on pitch properly, but it has been a very rare occurrence when some have actually done my bidding.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bad reed
« Reply #2 on: November 28, 2023, 12:21:20 PM »

I’ve found it is usually some almost imperceptible contact with the reed plate. It can be as little as a tiny spot of corrosion on the edge of the tongue, or with zinc plates sometimes on the plate, or a burr on the edge from filing.  Can also be a tiny contact down near the rivet end. Which is harder to fix.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Bad reed
« Reply #3 on: November 28, 2023, 12:27:58 PM »

I’ve found it is usually some almost imperceptible contact with the reed plate. It can be as little as a tiny spot of corrosion on the edge of the tongue, or with zinc plates sometimes on the plate, or a burr on the edge from filing.  Can also be a tiny contact down near the rivet end. Which is harder to fix.

Yes, this was my thinking, too, but filing down the profile of the reed did not help. It’s possible that it’s down near the rivet end as you said, which I’ve not had much luck fixing.
Logged
C#/D player

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Bad reed
« Reply #4 on: November 28, 2023, 01:26:20 PM »

I've seen this many times - perhaps one reed in every third or so box, that just acts weird under different pressures.

For some reason, a number of the reeds started acting normal if I changed the profile (curve) of the reed. I have a suspicion that it has something to do with the flex of the steel versus how is oscilates under pressure, and adding a tiny bit more curvature and re-setting the gap sometimes does the trick. Other times it doesn't.
I've also seen it in older reeds where the rivet end quarter was quite thin compared to the tip end - as if they've made the reed to short and tried to get it down it pitch by profile grinding it a little more than they probably should. Taking off a little material from the tip half (not just the tip) helped with pitch stability and the need for retuning is minimal - you just want to change the oscilation pattern a little, so it's not much that's needed, and as it's spread out over maybe half the reeds length we're maybe talking 5-10 cents tuning needed afterwards.

And then there's those last few reeds a year that just goes in the bin.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bad reed
« Reply #5 on: November 28, 2023, 01:29:01 PM »

File the profile means the top surface to me?
On the edges it can be sufficient to scrape round all the edges with a scalpel blade.  These have a sufficiently sharp point that it’s possible to scrape down near the rivet end where you can’t lift the tongue enough to us a file. I’ve just bee working on some Hohner zinc reeds and a few had obstructions at the tip in the corners of the vent, no way of telling if it was corrosion or dirt but scraping it out with a scalpel helped.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Bad reed
« Reply #6 on: November 28, 2023, 01:30:15 PM »

One of the causes for this behaviour I have tracked down after re-valving a reed plate is a small amount of adhesive sneaking around the rivet end of the adjacent reed, can be a real bugger to remove. I have since learned to be less sloppy when re-valving

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Bad reed
« Reply #7 on: November 28, 2023, 01:41:52 PM »

Yes, I'm talking about filing the top surface of the reed.

This is of course after the usual bits of troubleshooting:
- Cleaning
- Revalving
- Checking for debris
- Filing edge and checking in light
- Tightening rivet
- Checking chamber for loose wood fibre etc.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal