Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Another "tutorial" of how to tune an accordion...  (Read 8314 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Another "tutorial" of how to tune an accordion...
« Reply #1 on: January 05, 2024, 04:09:58 AM »

That sound! I can’t look…
Logged
C#/D player

Roger Hare

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 949
  • Urmston, Lancashire, U.K. éééé
Re: Another "tutorial" of how to tune an accordion...
« Reply #2 on: January 05, 2024, 07:59:13 AM »

It's not a place where I would ever venture, but it all looks a bit brutal? It also reminds me I have a visit to the dentist booked for Monday...
Logged
My ABC tune collections can be found here (GoogleDrive) & here (Dropbox).

For more about Manchester Morris, The Beech Band Folk Club or anything else,  please use the private messaging facility.

Helena Handcart

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2452
  • Saltarelle Nell
Re: Another "tutorial" of how to tune an accordion...
« Reply #3 on: January 05, 2024, 09:39:16 AM »

Nope, nope and NOPE. No one's tuning any of my boxes like that.
Logged
Saltarelle Le Romané  | Saltarelle Nuage | Oakwood | various elderly Hohners

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Another "tutorial" of how to tune an accordion...
« Reply #4 on: January 05, 2024, 10:35:09 AM »

All that effort, what ever you think about power tools, when the block goes back in the instrument the tuning will change. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

jarviw

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 156
Re: Another "tutorial" of how to tune an accordion...
« Reply #5 on: January 05, 2024, 03:06:57 PM »

All that effort, what ever you think about power tools, when the block goes back in the instrument the tuning will change.

Just curious, when the block goes back in the box, do the pitches change fairly evenly to the same direction across the different notes, or just all over the place?
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Another "tutorial" of how to tune an accordion...
« Reply #6 on: January 05, 2024, 03:36:59 PM »

Just curious, when the block goes back in the box, do the pitches change fairly evenly to the same direction across the different notes, or just all over the place?

I think "fairly evenly" is about right. Each reed tends to be consistent in itself, so there is a tuning technique where you measure the frequencies of all the reeds while in the box, subtract from what they should be then take them out of the box and change the tuning of each reed by by its calculated offset. When you put them back in the box they should in theory be correct, but even that is not said to be foolproof.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Another "tutorial" of how to tune an accordion...
« Reply #7 on: January 05, 2024, 04:00:41 PM »

My experience is that the changes are not consistent and depend on pitch so for example high pitch  reeds can change a different amount from low. It also depends on the position of the reed block.  Reeds that are facing another block, or are close to another surface are affected more, and those facing a larger space are affected less.  The amount of pallet lift also makes a difference which can affect one side of a block more than the other.  The design of your rest bellows outside the box is also an important factor where the thickness of the top plate and the size of the air holes are the most significant variables. 
The techniques to tune in the box don’t take an enormous amount of time to learn, and the tools required are simple.  I’m always happy to share my methods.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Another "tutorial" of how to tune an accordion...
« Reply #8 on: January 05, 2024, 04:42:39 PM »

The design of your rest bellows outside the box is also an important factor where the thickness of the top plate and the size of the air holes are the most significant variables. 

I was trying to convey this in a previous thread, but my suggestion was shot down!
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Another "tutorial" of how to tune an accordion...
« Reply #9 on: January 05, 2024, 08:20:39 PM »

It's not only that the frequency may change significantly when the blocks are back in the instrument. To mention just three of several  other invaluable advantages of tuning in situ is a) the fact that it allows you to use the keyboard and quickly check intervals, also across reed blocks (+ make use of registers, if present). And b) an accurate tremolo tuning is only possible with the blocks in situ, when the tuner must be able to quickly cross-reference with neighboring  notes. c) it's so much faster! By the time this guy has finished ruining one reed, I'm already done tuning a whole row...
 
« Last Edit: January 06, 2024, 10:00:03 AM by diatonix »
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Another "tutorial" of how to tune an accordion...
« Reply #10 on: January 06, 2024, 08:40:59 PM »

Oh my valves!!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Another "tutorial" of how to tune an accordion...
« Reply #11 on: January 08, 2024, 09:56:04 PM »

My experience is that the changes are not consistent and depend on pitch so for example high pitch  reeds can change a different amount from low. It also depends on the position of the reed block.  Reeds that are facing another block, or are close to another surface are affected more, and those facing a larger space are affected less.  The amount of pallet lift also makes a difference which can affect one side of a block more than the other.  The design of your rest bellows outside the box is also an important factor where the thickness of the top plate and the size of the air holes are the most significant variables. 
The techniques to tune in the box don’t take an enormous amount of time to learn, and the tools required are simple.  I’m always happy to share my methods.

Would love to hear your in box method. I have my table set up to do a rough tune (off the block), single notes (on the block), both notes together, to tune tremolo and finally in the treble case but not assembled and I find that there is quite a difference when everything is all together.

Please share
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Another "tutorial" of how to tune an accordion...
« Reply #12 on: January 08, 2024, 10:51:12 PM »

My method is quite simple.  If there is no change of pitch  I just tune the reeds in situ in the instrument, usually the instruments own bellows hanging in a.simple fixture clamped to the edge of the bench.   If there is a change of pitch, for example tuning up from 435 to 440,  or a conversion from  one key to another then I rough tune singly on a very simple wooden holder on a test bellows.  I aim for very approximately 10 cents sharp of the target pitch.  Once the reeds are valves and waxed  and fitted in the box they usually drop by a few cents.  Then they are ready for final tuning.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Stefan

  • Member
  • *
  • Offline Offline
  • Posts: 46
Re: Another "tutorial" of how to tune an accordion...
« Reply #13 on: January 09, 2024, 10:47:59 PM »

My method is quite simple.  If there is no change of pitch  I just tune the reeds in situ in the instrument, usually the instruments own bellows hanging in a.simple fixture clamped to the edge of the bench.   If there is a change of pitch, for example tuning up from 435 to 440,  or a conversion from  one key to another then I rough tune singly on a very simple wooden holder on a test bellows.  I aim for very approximately 10 cents sharp of the target pitch.  Once the reeds are valves and waxed  and fitted in the box they usually drop by a few cents.  Then they are ready for final tuning.
with all respect, if your workflow is that way, fine. I today finished an erica, tuned on a table and surprisingly its nearly spot on. And i had used a dremel too ( >:E) In opposite to the video above i removed the reeds and tuned them without valves. I found out that the result is best if i use the original cleaned reedblock, the original cell, and the direction it will be waxed in later. I just push the reedplate agains the block and either push or pull the bellows of my tuning table. I use tape to simulate the valves and my tuning table is small and has nearly similar dimensions as a melodeon. As a rule of thump i tune one row spot on (accurate to the cent) and start with a difference of 22 cent on the lowest reeds and substract 1,5 cent with every higher reed. This is more flat than the original hohner tremolo but i like the medium swing it results in. The last box was a ww2 double ray (laurel leaf) wich i tuned (on the table) as dry as i can get, just to experiment how much the result will differ if the block are installed later, and i found the result surprisingly identical.
There is nou doubt that you are the much more experienced tuner BUT a beginner has to begin somewhere and i think you take the courage out of newbies as you allways repeat your statement that one could not tune another way you do and tuning tables and powertools are inadequate. Maybe my tuning skills are not perfect but my philosophy is to tune as good as possible on the table because tuning in situ is a pita and i think scratching and bending the tongues does unnecessarily stress the material. (and the traces of filing from previous tunings are partially much more worser than what my dremel leaves behind).
btw. I dont think one could get same results with "very simple wooden holder", and taping one side (simulating valves) is important too because the pitch does change if "unvalved" No offense!
Logged

Jack Humphreys

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • tunesbyjackhumphreys
Re: Another "tutorial" of how to tune an accordion...
« Reply #14 on: January 12, 2024, 08:39:21 AM »

I have a relevant story. I took my French-made 3v box to a professional tuner, who, after many hours of struggling, opined that the box was badly made and that the Binci reeds were "unstable".  He said that he was therefore unable to deliver the requested slight swing tuning on MM, and recommended a unison tuning, which I ignorantly accepted.
I was soon bored with unison MM, and took the box to a second tuner, who successfully delivered the slight swing I wanted. He did some work on the reeds outside the box,  but the final tuning was in-box. 
I retrospect, I believe that the first tuner relied entirely on tuning outside the box, using offsets. He said there was "no room"  to tune inside the box, so I assume he was using a rotary grinder/polisher.   The reeds' "instability"  was presumably because the pitch altered unpredictably between the outside-box tuning and the inside-box result.  My second tuner found that all the reeds had been removed and rewaxed, as part of the first tuner's struggles to make his method work.
« Last Edit: January 12, 2024, 08:56:54 AM by Jack Humphreys »
Logged

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Another "tutorial" of how to tune an accordion...
« Reply #15 on: January 12, 2024, 09:59:34 AM »

with all respect, if your workflow is that way, fine. I today finished an erica, tuned on a table and surprisingly its nearly spot on. And i had used a dremel too ( >:E) In opposite to the video above i removed the reeds and tuned them without valves. I found out that the result is best if i use the original cleaned reedblock, the original cell, and the direction it will be waxed in later. I just push the reedplate agains the block and either push or pull the bellows of my tuning table. I use tape to simulate the valves and my tuning table is small and has nearly similar dimensions as a melodeon. As a rule of thump i tune one row spot on (accurate to the cent) and start with a difference of 22 cent on the lowest reeds and substract 1,5 cent with every higher reed. This is more flat than the original hohner tremolo but i like the medium swing it results in. The last box was a ww2 double ray (laurel leaf) wich i tuned (on the table) as dry as i can get, just to experiment how much the result will differ if the block are installed later, and i found the result surprisingly identical.
There is nou doubt that you are the much more experienced tuner BUT a beginner has to begin somewhere and i think you take the courage out of newbies as you allways repeat your statement that one could not tune another way you do and tuning tables and powertools are inadequate. Maybe my tuning skills are not perfect but my philosophy is to tune as good as possible on the table because tuning in situ is a pita and i think scratching and bending the tongues does unnecessarily stress the material. (and the traces of filing from previous tunings are partially much more worser than what my dremel leaves behind).
btw. I dont think one could get same results with "very simple wooden holder", and taping one side (simulating valves) is important too because the pitch does change if "unvalved" No offense!

I *really* don't understand this, erm, approach. Tuning in situ is actually very easy, it's just something, as all manual work of any kind, that needs being used to. I find it easier than designing all the tinkering you're doing to avoid a simpler, more efficient way.
To each person its method, but I don't understand coming here to boast about refusing to use recognised, tested, methods, apart from wanting to upset people.

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Another "tutorial" of how to tune an accordion...
« Reply #16 on: January 12, 2024, 08:41:37 PM »



I *really* don't understand this, erm, approach. Tuning in situ is actually very easy, it's just something, as all manual work of any kind, that needs being used to. I find it easier than designing all the tinkering you're doing to avoid a simpler, more efficient way.
To each person its method, but I don't understand coming here to boast about refusing to use recognised, tested, methods, apart from wanting to upset people.

Thanks, I couldn't have worded this better myself!
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Another "tutorial" of how to tune an accordion...
« Reply #17 on: January 12, 2024, 08:53:07 PM »

"apart from wanting to upset people."

Why would anyone want to be "upset" by this man's post? He's only stating what his preferred tuning method is.
After all, some strange people put the milk in their cup before the tea, I don't like it! But it certainly wouldn't upset me. And I couldn't imagine that they were doing it to specifically upset other tea drinkers, either.

Surely we can disagree without such harshness?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Another "tutorial" of how to tune an accordion...
« Reply #18 on: January 12, 2024, 09:16:30 PM »

Why would anyone want to be "upset" by this man's post?

Unprofessional "tuning" very often goes hand in hand with other examples of malpractice (apart from damaged reeds) such as messy waxing and poor handling/choice of valves and others. Issues, I, being a licensed, professional tuner, have to address before being able to concentrate on what is my real task. Of course it upsets me! And it also upsets my customers, who not only wasted their money dealing with a self-taught unskilled amateur, but are now presented with my bill, where I am forced to charge for more of my time than would have been necessary.
« Last Edit: January 12, 2024, 09:41:30 PM by diatonix »
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Another "tutorial" of how to tune an accordion...
« Reply #19 on: January 12, 2024, 09:29:48 PM »

Is he tuning for other people? I didn't deduce that from his post.

I understand your frustration at having to rectify DIY type work before you can redo it properly, as this used to happen to me, when I was working.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal