Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Button Board Build  (Read 1845 times)

0 Members and 1 Guest are viewing this topic.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Button Board Build
« on: January 07, 2024, 05:16:28 PM »

I was fortunate enough to pick up one of Pete's button boards from Acorn Instruments before he stopped making them. If you love old Hohners like I do then you have definitely picked up nice old boxes with smashed button holes. I've done my best to frankenstien them together in the past with mixed results but it's always a bit rough. A good friend of mine owns a CNC machine and we have recently been doing some R&D on making some boards, at least for my collection. So far we have only made one prototype and the results look really promising. Just using scrap wood until we have the program tweaked and then we will decide what materials will work best. We have some really nice clear yellow cedar, enough to make eight boards right now. I'm not sure if this will be too soft though? Curios to hear input from others who have tackled this. Cheers
IMG_6840 by Pat McInnis, on Flickr


YFyQl7XMTeeRGlWyN7z+1w by Pat McInnis, on Flickr
Logged

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: Button Board Build
« Reply #1 on: January 07, 2024, 05:52:11 PM »

Looks good!.. I’m still looking for a replacement keyboard for an Erica type Double Ray, so if you’re willing to offload one of your prototypes for a reasonable amount, let me know via pm… Cheers!
Logged
Dancing about architecture since 1997

chris hall

  • Regular debater
  • ***
  • Online Online
  • Posts: 245
Re: Button Board Build
« Reply #2 on: January 07, 2024, 06:32:23 PM »

we made some at derby melodeons ...mostly for 114 hohners but also for ericas. after discussing with pete we took his advice and went for aircraft ply for the fronts and removeable backs (a stable material that isnt likely to warp). for the rest of the construction we used kiln dried maple. (hardwood is hard wearing and good for screwing into but maybe something softer might have worked) we stained them with 3 or 4 coats of liberon stain and finished with 5 or 6 coats of liberon finishing oil. again on petes advice we stained and oiled both sides of the ply to avoid warp. CNC could be a good idea. We used a more traditional approach for fingerboards but used CNC to make reed blocks and after a lot of trial and a lot of errors in programming it all it and getting the machinery to behave it finally worked really well (making reed blocks out of maple for single row boxes)
Logged

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Button Board Build
« Reply #3 on: January 07, 2024, 07:35:33 PM »

Hi,
Something that you do not seem to have spotted from the picture of your set up,the holes are not cut at 90 degrees to the face of the fingerboard.
Good luck

Pete
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Button Board Build
« Reply #4 on: January 07, 2024, 08:11:09 PM »

I would have thought cedar a bit too soft.
Beech would be my timber of choice, but walnut or similar would be equally good, and a bit darker to start with if you are going to stain black.
I have made a some small plywood boards from walnut veneer with a core of oak constructional veneer. It totals around 2.5mm.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Button Board Build
« Reply #5 on: January 07, 2024, 09:24:55 PM »

I would have thought cedar a bit too soft.
Beech would be my timber of choice, but walnut or similar would be equally good, and a bit darker to start with if you are going to stain black.
I have made a some small plywood boards from walnut veneer with a core of oak constructional veneer. It totals around 2.5mm.
The original Hohner keyboard from what I’ve seen are a clear pine , but with old growth trees.
I would say what ever you use it is tight grain/ dry stable wood. I made one for a one row out of cherry which is another option. I did not have a CNC so I just used a drill press. 
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Chris Marriott

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1048
Re: Button Board Build
« Reply #6 on: January 08, 2024, 04:50:52 PM »

I would have thought cedar a bit too soft.

An advantage of cedar is that it absorbs moisture without swelling or warping. It's used for the blocks of wooden recorders for that reason.
Logged
Chris

Castagnari Mory, English Concertina and Piano Accordion.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Button Board Build
« Reply #7 on: January 08, 2024, 05:22:21 PM »

Hi,
Something that you do not seem to have spotted from the picture of your set up,the holes are not cut at 90 degrees to the face of the fingerboard.
Good luck

Pete

Thanks for chiming in Pete. Still enjoying the original one from you. OK I don't entirely understand what you mean by a 90* cut to the face for the holes. I don't have the old boards in front of me but I dont recall seing such an angle built in.

Thanks as well to everyone else for all the tips and advice. We don't really pretend to know what we're doing here, so helpful advice is always appreciated.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Button Board Build
« Reply #8 on: January 08, 2024, 05:43:30 PM »

Quote
OK I don't entirely understand what you mean by a 90* cut to the face for the holes.

That makes 2 of us ! (:) I thought maybe he meant to provide clearance for the top part of the buttons that move in an arc as they (try to) sink in and may catch the upper part of a close-tolerance holes.  I've seen that in a few boxes (not Hohners), but I would have thought the usual Hohner ovalish hole was large enough not to need that.

 
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Button Board Build
« Reply #9 on: January 08, 2024, 05:57:51 PM »

Quote
OK I don't entirely understand what you mean by a 90* cut to the face for the holes.

That makes 2 of us ! (:) I thought maybe he meant to provide clearance for the top part of the buttons that move in an arc as they (try to) sink in and may catch the upper part of a close-tolerance holes.  I've seen that in a few boxes (not Hohners), but I would have thought the usual Hohner ovalish hole was large enough not to need that.

Yes, but the angle for that clearance is built into the block itself where it mates to the case. still confused.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Button Board Build
« Reply #10 on: January 08, 2024, 06:39:15 PM »

See if the attached rough sketch makes sense (clearly my keyboard front did not come off your friend's CNC !)

Logged

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Button Board Build
« Reply #11 on: January 08, 2024, 08:32:32 PM »

Quote
OK I don't entirely understand what you mean by a 90* cut to the face for the holes.

That makes 2 of us ! (:) I thought maybe he meant to provide clearance for the top part of the buttons that move in an arc as they (try to) sink in and may catch the upper part of a close-tolerance holes.  I've seen that in a few boxes (not Hohners), but I would have thought the usual Hohner ovalish hole was large enough not to need that.

I made mine as a copy of an original and the holes were not at 90 degrees to the face of the board.
When I machined the ones that I produced the back edge of the keyboard was kicked up and holes machined with an overhead router on a jig

Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Button Board Build
« Reply #12 on: January 08, 2024, 09:00:29 PM »

See if the attached rough sketch makes sense (clearly my keyboard front did not come off your friend's CNC !)

It does make sense but I guess I'm wondering if it's necessary? Original oblong holes cut in the face seem to have plenty of clearance for both the button and the button lever. I'm assuming that the mod Pete made was for a good reason besides aesthetics. 
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Button Board Build
« Reply #13 on: January 09, 2024, 01:42:23 AM »

I guess it makes sense, treble/ pallet mech. Is 90 degrees to the fondo and the keyboard is pitched back . I built one for a 1040 and just drilled straight and then just opened the hole by hand/ file. I also just put a new keyboard face plate on my two row B/E box , same thing. Not that you would want to do hand work on it if productivity is a concern.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal