Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner register switch leather hoods  (Read 1245 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Hohner register switch leather hoods
« on: January 20, 2024, 06:41:14 PM »

Hi All,

Hoping for some advice about replacing register switch leather hoods on an old hohner.

There's a leather gasket glued to the soundboard & leather hoods glued to the gasket, then wrapped around register rods (white hoods in the photo).
Has anyone figured out a modern material/approach to replace them with?
I can go for the same old leather + tie them up with some waxed string approach, but the thinnest leather I have is 2mm and it's nowhere near being flexible enough to pull this off.
I don't have a splitting machine or even a skiving knife any more, so the best I can think of would be to cut a strip of 2mm leather and sand the flesh side (long & painful manual process).

Any suggestions how to tackle this are welcome.


PXL-20240120-183047401" border="0
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner register switch leather hoods
« Reply #1 on: January 20, 2024, 07:50:51 PM »

Ladies leather gloves from a charity shop?  Glove leather will be thin and flexible enough.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Hohner register switch leather hoods
« Reply #2 on: January 21, 2024, 09:51:33 AM »

Good idea, thank you.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Hohner register switch leather hoods
« Reply #3 on: March 16, 2024, 05:01:00 PM »

Not happy with the results I'm getting using thin leather.

How about latex?  ;D

PS Googled "Small latex hood". Yikes! Let's not go there.

Old bicycle tubes?
« Last Edit: March 16, 2024, 06:39:35 PM by mChavez »
Logged

Dow Mathis

  • Member
  • *
  • Offline Offline
  • Posts: 14
Re: Hohner register switch leather hoods
« Reply #4 on: March 16, 2024, 07:19:14 PM »

What about the finger out of a nitrile or latex glove?
Logged
Dow Mathis ∴
Boerne, TX

Nothing is foolproof to a sufficiently motivated fool.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Hohner register switch leather hoods
« Reply #5 on: March 16, 2024, 08:07:45 PM »

That's how I got the latex idea. But I think latex tends to split & burst if it gets even a tiny hole - latex racing bike tubes are notorious for that. I think just a regular butyl tube might be better.

Leather is certainly doable, but it's quite tricky to wrap it around the pushrod, then glue onto the fondo. With butyl I reckon I can just punch a hole in it and push the rod in, then wrap some waxed string around it.

Will let you know how I get on.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Hohner register switch leather hoods
« Reply #6 on: March 17, 2024, 12:07:59 AM »


Leather is certainly doable, but it's quite tricky to wrap it around the pushrod, then glue onto the fondo. With butyl I reckon I can just punch a hole in it and push the rod in, then wrap some waxed string around it.

Will let you know how I get on.
Could you use the finger of the glove? Make a hole in the tip of the finger then push it down over the rod and glue it in place. It will save having to wrap it around.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal