Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Non-sounding reed  (Read 1740 times)

0 Members and 1 Guest are viewing this topic.

Richard Baalham

  • Member
  • *
  • Offline Offline
  • Posts: 6
Non-sounding reed
« on: February 01, 2024, 05:44:45 PM »

Hi,
So... I have suffered a case of MAD and bought a Club 2B Victoria.

The problem I am trying to deal with is that one of the keys will not sound on squeezing the bellows, I find it quite strange that both reeds on the same key for the same direction are suffering the same problem, maybe that is normal.

Going through this forum, YouTube etc I went to work. I pulled out the reed block, after cleaning out all the dust behind the pallet chamber (or whatever it is called) and inside the bellows, inspected, cleaned the reeds and 'twanged' so the reed now looks good but still no sound.

Any suggestions on what to do next?  I am in NZ so have limited access to professional help, replacement parts might be an issue.

Cheers,,

Richard


Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Non-sounding reed
« Reply #1 on: February 01, 2024, 06:09:50 PM »

Check the reed gap; make sure that the reed tongue rests slightly above the reedplate itself, and is not flush or recessed in its opening. In a case of the latter, the reed tongue will still ‘ping’ upon inspection but not sound when played in the instrument or on the block. Next, make sure the reed tongue is perfectly centred within its opening, and not too far one way or the other. If you’re able to push the reed tongue into its opening freely, it should at least sound when played, even if further adjustment is necessary. Also check to make sure that both valves are able to open and close freely and are not stuck shut for any reason.
Logged
C#/D player

Richard Baalham

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Non-sounding reed
« Reply #2 on: February 01, 2024, 08:52:19 PM »

Thanks for the steer... I have had a bit of a go at following your instructions, so far no joy - but not beaten yet!
Logged

fc diato

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 146
Re: Non-sounding reed
« Reply #3 on: February 01, 2024, 09:03:35 PM »

I assume you checked that the pallet is actually lifting when you press the key? Likely not the issue, since you would probably feel it in the key...
Logged
fc diato

Richard Baalham

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Non-sounding reed
« Reply #4 on: February 01, 2024, 10:02:23 PM »

Yup, the pallets lift nicely, a good thing to check. I notice that the rows lift differently but are consistent along the row, guess that is normal. The buttons on the 1st row are a little low (future project maybe) but do not interfere with the pallet 'breathing' as far as I can tell, bellows are tight. The leather valves could do with renewing and the pallet facings *may* need a look as well but that's a bit down the track. This is a bit of a puzzle, quite enjoying it so far :)
Logged

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: Non-sounding reed
« Reply #5 on: February 01, 2024, 10:45:54 PM »

Reeds waxed or pinned on gaskets?
Logged
Too many accordions, help!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Non-sounding reed
« Reply #6 on: February 01, 2024, 10:59:54 PM »

The most common reason for non sounding reeds is something physically stuck around the gap between the reed tongue and the plate.  Is there any rust on the reed?  If so sometimes there can be a nugget of rust on the edge of the reed that can stop it moving freely. 
When you ping the reed it should make a clear sound.  Compare it with reeds that are working and listen for obvious differences.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Richard Baalham

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Non-sounding reed
« Reply #7 on: February 01, 2024, 11:19:12 PM »

Hi komat, not sure exactly what you mean but it looks like the reeds are waxed onto the frames without any gaskets and then pinned in place, nothing looks amiss with this, looks like no one has touched it since it was built. The leather valves are a bit floppy, but that shouldn't cause this from what I can tell....

Hi Theo, there was a little bit of rust, it was at the level of discolouration and did not seem too bad to my eyes...  I used some very fine wire wool backing the reed with some paper to stop debris from falling into the chambers, air duster afterwards etc. To my ears, they ping clearly.
If they need to be spotless then I'll have to go and get some very fine emery paper (or????)  and clean them up some more... be back in a few days with the results!

Thank you all for being so helpful, I am a bit taken aback by this response!
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Non-sounding reed
« Reply #8 on: February 02, 2024, 12:53:36 AM »

Hi komat, not sure exactly what you mean but it looks like the reeds are waxed onto the frames without any gaskets and then pinned in place, nothing looks amiss with this, looks like no one has touched it since it was built. The leather valves are a bit floppy, but that shouldn't cause this from what I can tell....

Hi Theo, there was a little bit of rust, it was at the level of discolouration and did not seem too bad to my eyes...  I used some very fine wire wool backing the reed with some paper to stop debris from falling into the chambers, air duster afterwards etc. To my ears, they ping clearly.
If they need to be spotless then I'll have to go and get some very fine emery paper (or????)  and clean them up some more... be back in a few days with the results!

Thank you all for being so helpful, I am a bit taken aback by this response!
I wouldn’t go too crazy with the cleaning with paper or steel wool. A floppy valve would probably only be a real problem if it falls off inside the block, you did check the reed block hole to look for blockage, right? I imagine that if you had pinged the inside reed though the hole you would have seen something. Otherwise keep looking for something in the channel between the reed or on the reed as Theo suggested, it can be the smallest of things. You might need to pull the reed to get a good look in the light. I also find it funny that both reeds are a problem. When you lift the pallet on the offending reeds, do you see anything ( tape ) covering the hole or holes?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Richard Baalham

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Non-sounding reed
« Reply #9 on: February 02, 2024, 02:18:12 AM »

Hi boxcall, yes, shone a torch into the hole of the reed block, then used the light to check for a clean unbroken line around the reed... still mystified. There are no blockages that I could see either, and the pallet is definitely clear of any obstruction, as I looked for this as well.... it is a little misaligned but from the 'shadow' on the wood, this has been the case since construction so immaterial.   
I have an offer from someone close to where I live to give me a hand to localise the problem, will be a few days until we meet so I will have to leave you all wondering what might be the cause for a few days more!
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Non-sounding reed
« Reply #10 on: February 02, 2024, 05:46:18 AM »

Wondering whether the leather pallet facing is parting company with the rest of the pallet, and remaining over the holes when the pallet is lifting. Worth a further close inspection perhaps....
Logged
Tuner/repairer, now retired.

WestOz

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 197
Re: Non-sounding reed
« Reply #11 on: February 02, 2024, 08:53:39 AM »

As Mselic says:

Check the reed gap; make sure that the reed tongue rests slightly above the reedplate itself, and is not flush or recessed in its opening. In a case of the latter, the reed tongue will still ‘ping’ upon inspection but not sound when played in the instrument or on the block
Logged
Castagnari Dony, DB Binci, Hohner Pressedwood,  Liliput, Preciosa,Octoput,etc.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Non-sounding reed
« Reply #12 on: February 02, 2024, 02:39:07 PM »

Wondering whether the leather pallet facing is parting company with the rest of the pallet, and remaining over the holes when the pallet is lifting. Worth a further close inspection perhaps....

I wondered about this, too.
Logged
C#/D player

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Non-sounding reed
« Reply #13 on: February 02, 2024, 05:21:43 PM »

Quote
The problem I am trying to deal with is that one of the keys will not sound on squeezing the bellows, I find it quite strange that both reeds on the same key for the same direction are suffering the same problem, maybe that is normal.

If the faulty note is on squeezing (closing) the bellows, faulty pallet leather would not prevent air escaping and the reeds sounding.  If it's on the pull, then yes it's a possibility.

Is the note in the other bellows direction on the same button working ok ??
Logged

Richard Baalham

  • Member
  • *
  • Offline Offline
  • Posts: 6
Re: Non-sounding reed
« Reply #14 on: February 08, 2024, 08:47:01 PM »

So, I have made some headway with a little lot of help from Nigel (thank you!).

I managed to get the reed to sound, it was a combination of not being straight (the tip was turned up) and sitting too low. 
A couple of other problems seem to stem from the lack of valves, so I will work on fixing those up over the next little while. Lastly, I have a low-sitting key, so again some careful manipulation should put that right...   

After this, I have no further excuses so will need to get into learning a tune!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal