Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Wooden action & axles re-build  (Read 2744 times)

0 Members and 1 Guest are viewing this topic.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Wooden action & axles re-build
« Reply #20 on: February 18, 2024, 12:52:10 PM »

...I might sound incredibly tight-fisted but buying all these things in small quantity quickly adds up to a used Handry 18 if one's not careful...


The most expensive part of buying a length of stainless rod is the postage (about a fiver). A quick search found suppliers selling individual pieces for £1.69, for a 39" piece.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #21 on: February 29, 2024, 01:30:39 PM »

FWIW, putting a simple spear point on the tip of a 2mm rod, chucking it into a drill and opening up the holes seems to have worked well with 2.0 rod into 1.6 and 1.2mm holes.
I've re-applied wax to the rod several times as I was reaming the axle slot, as things start heating up pretty quickly once you're half way through the keyboard.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #22 on: March 10, 2024, 02:34:27 PM »

Hi All,

A couple more questions about the key fit:
1) What should be the gap between the sides of the key and the key slot. I.e. should I aim to minimise the slack as much as possible, or it's fine if there's a 1mm gap (key is narrower than the slot by 1mm).
2) For enlarging the key axle holes, would you do it while the keys are out of the keyboard (e.g. on a pillar drill) or would you hold the key in place and ream it by driving the sharpened axle into the keyboard?

Thanks.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #23 on: March 13, 2024, 07:32:58 AM »

No Suggestions?
In particular, should I glue on some veneer on the sides of the keys to close ~1mm clearance between the key and the slot sides?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wooden action & axles re-build
« Reply #24 on: March 13, 2024, 08:38:52 AM »

The clearance required will depend on how much sideways movement the key has on the axle rod.  You need enough clearance so that there is no wood to wood contact along the sides of the lever.  Some of the more basic wooden keyboards I’ve seen have quite wide clearance at the side, possibly because it is easier (and therefore cheaper) to have a little more clearance on the axle rod than would be ideal.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #25 on: March 13, 2024, 09:42:05 AM »

I see, thank you.

Since I'm fitting the keys to the axle myself, I expect a very tight fit there. Will a large gap between the keys and the sides of the slot be detrimental? Likely to loosen up the axle holes a lot faster?
« Last Edit: March 13, 2024, 09:58:10 AM by mChavez »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wooden action & axles re-build
« Reply #26 on: March 13, 2024, 10:48:38 AM »

I could only guess.  You haver everything in front of you so it's a case of using your judgement.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #27 on: March 13, 2024, 11:31:37 AM »

Judgement requires experience, and mine is 100% with aluminium & brass-levered mechs. I don't like the idea of wood-on-metal contact in critical joints. I think the whole idea is a hundred years out of date.
But this box is from mid 1800s and I'm quite keen to get it playing, so I'll just have to live with the wooden action on this one.
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal