Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Wooden action & axles re-build  (Read 2743 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Wooden action & axles re-build
« on: February 16, 2024, 09:19:50 AM »

Hi all,

I am rebuilding a very old melodeon (pretty much from scratch given the sad condition  :-[) and I've got a two-axle keyboard that needs to be completely overhauled (stuff cracked & a couple glue joints broken off, so can't leave as is). The axles are steel, 1.3mm and 1.6mm running straight through wood (beech). Used up a bucket of elbow grease, but managed to remove the original axles without breaking anything. They are a bit rusty, a bit bent and a bit surface damaged from having to keep clamping them in a vice, so I am thinking of replacing them.

If I could, I'd bush the keys with brass inserts & run a 2mm brass axle, but some of the keys are so small, there's no space for the bushings. It will have to be wood-on-metal contact.

I've got 1.9mm and 2.0mm brass and titanium rods - would these be good materials to leave in contact with beech? For brass I can put an M2 thread on it and install a threaded insert into the keyboard base, turning the axle into a screw-fit instead of push fit. Don't think I can tap Ti.
I can sharpen the tip of one of the rods and enlarge the existing holes to 1.9-2.0mm. Not sure what to do for the keys. Pretty sure I have a 2.2mm reamer. Maybe even a 2.1. What sort of tolerance is required, given it's wood and it will move. (I'll probably drop some CA into the holes to stabilise them and then ream...if that's a good idea?).

Any advice (including "Get a life") welcome.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Wooden action & axles re-build
« Reply #1 on: February 16, 2024, 05:08:17 PM »

I think I would go the lazy way.  See if you can clean,straighten and reuse the old axles first.  Failing that, try and find steel replacements of the same size to avoid redrilling.  They're fairly inexpensive and just a few mouse clicks away. 
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wooden action & axles re-build
« Reply #2 on: February 16, 2024, 05:18:50 PM »

Whichever way you go watch the clearances between wood and axle.  Even a  very small clearance can result in keys that can move and rub on adjacent structures.  It also gives the keyboard a sloppy feel which is not so nice to play. I would use a reamer no larger than the diameter of the rod. When keys are tight on the 2mm axle on modern boxes I use a 2mm twist drill held in my fingers to very gently pass through the hole with a slight twisting movement.  I rarely see any cuttings, but it’s usually enough to get the lever to move freely.  Another trick (learned from Emmanuel Pariselle) is to roughen the surface of a piece of the same material as the axle rod and use that as a very gently sort of reamer.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #3 on: February 16, 2024, 05:29:58 PM »

Thank you very much.

Old rods can be re-used, but the key holes are quite worn (need bigger diameter axles) and some of the holes in the comb will have to be re-drilled anyway, as they'll get contaminated with glue when I put the broken piece back on.

Sounds like putting a spear-shaped edge on a future axle and feeding it into the existing holes while turning by hand or drill with very low revs is the way to go.

Which metal will be least affected by the wood in the long term? Brass? Ti? Steel tends to rust unless I find stainless?

What clearances should I aim for between the comb walls and the keys? (dang, it's so much easier with aluminium and brass bearings...)
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Wooden action & axles re-build
« Reply #4 on: February 16, 2024, 06:53:34 PM »

I’ve seen brass inserts/conduits used to accommodate axle rods on several one-row boxes with wooden levers. It’s a clever design, but in one case the insert was actually seized to the axle rod which actually prevented me from tapping the rod out since it was causing damage to the surrounding wooden components. I’d avoid using them for this reason.

Also, I second what Theo says about enlarging the holes in the keys for axle rods. Never use a drill bit or reamer any wider than the axle rod itself; it will be too loose and the button action flimsy as a result.

The real solution to avoiding these issues (when building boxes) is to use a material other than wood for the keys/levers. In Quebec, some one-row builders use a kind of resin/plastic material for the actual key levers, and then top them with a wood veneer in cases where the keyboard is open.
Logged
C#/D player

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Wooden action & axles re-build
« Reply #5 on: February 16, 2024, 07:14:57 PM »

I use stainless steel axle rods.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Wooden action & axles re-build
« Reply #6 on: February 16, 2024, 07:19:10 PM »

A good source of material for axle rods is bicycle spokes, available in stainless steel.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #7 on: February 16, 2024, 07:42:56 PM »

A pity that I use double butted in my wheels. ::)
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #8 on: February 16, 2024, 07:49:57 PM »

The real solution to avoiding these issues (when building boxes) is to use a material other than wood for the keys/levers.

Yep. Aluminium & brass cost comparative peanuts and will still be there when I die. Plastic, most likely, won't - it might belong in the oceans, but it sure does not belong in musical instruments, imho.
I don't think plastics have been invented when this box was built, so I'll let the luthier off on this occasion.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Wooden action & axles re-build
« Reply #9 on: February 16, 2024, 09:02:10 PM »

The real solution to avoiding these issues (when building boxes) is to use a material other than wood for the keys/levers.

Yep. Aluminium & brass cost comparative peanuts and will still be there when I die. Plastic, most likely, won't - it might belong in the oceans, but it sure does not belong in musical instruments, imho.
I don't think plastics have been invented when this box was built, so I'll let the luthier off on this occasion.

Sorry, I shouldn’t have said plastic. It’s not that…it’s some kind of hard, black resin or whatnot that looks like it can be cut/carved. Mélodie and Sag’ne both use it to build the key levers in their one-row accordions.
Logged
C#/D player

Winston Smith

  • Hero Member
  • *****
  • Online Online
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Wooden action & axles re-build
« Reply #10 on: February 16, 2024, 10:31:48 PM »

Wanting no play between the axle, mountings or levers, I used a mild steel welding rod. Ground the first inch or so to slide through the first few original holes, then filed a couple of shortish flutes into the next inch or so; and then with a 90 degree bed as a handle I just gently wound it right through, to ream out all the holes as I went. Some of the rest of the rod worked nicely for the actual axle.
No play, no searching and waiting for parts, hardly any expense, and a job that would last well enough for an old box. I'm busy doing something vaguely similar to a metal Hohner mechanism just now, simply because I'm too hard-up to throw scarce cash out for a new one. It'll be smashing!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #11 on: February 17, 2024, 08:32:41 AM »

Thank you - I like the idea of grinding down the front of the "reamer" and the flutes.

Now that Theo mentioned it, I'm sure I've got some non-butted stainless spokes somewhere in the depths of the bike shed, but they might not be long enough, in which case it comes down to Ti vs brass.

Any reasons not to use Ti? It will be a couple grams lighter than stainless  ;D

Update: Found them...Too short.

No problem popping into a bike shop for a couple stainless spokes, but afaik, they are electroplated with some surface treatment, so it's not stainless on the outside. Which brings me back to the idea of using solid ti instead. Brass, I believe, oxidises(?) to green gunk from prolonged contact with wood.
« Last Edit: February 17, 2024, 08:51:16 AM by mChavez »
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #12 on: February 17, 2024, 02:58:58 PM »

On a related note: does anyone happen to have build plans for a 3-row keyboard?
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Wooden action & axles re-build
« Reply #13 on: February 17, 2024, 04:00:04 PM »

Stainless steel spokes from DT Swiss have been in my experience just plain ol stainless steel (barring the colored ones mind you). I've used them to make tools and I also used to be a bicycle mechanic for various shops for over a decade and have found that as long as they're the stainless straight gauge, theyre stable things and you can expect them to behave themselves. Galvanized spokes are another story, those you should stay very far away from  :P
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Wooden action & axles re-build
« Reply #14 on: February 17, 2024, 05:23:40 PM »

Why not just buy some stailess steel rod in the dimension you need? There are people selling on Ebay but, if you don't trust them, splash out and get some from RS/Farnell?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Wooden action & axles re-build
« Reply #15 on: February 17, 2024, 05:56:45 PM »

Well, if I have plenty of perfectly fine ti rod right here, why install stainless?

I might sound incredibly tight-fisted but buying all these things in small quantity quickly adds up to a used Handry 18 if one's not careful.

Dr Google says:
"4.1 METALS SUSCEPTIBLE
The corrosive agent is acetic acid emitted by the wood, and the metals most susceptible are
those readily attacked by it. The following list shows the degree of susceptibility to attack:
Group 1 – Severe attack
Cadmium,
Carbon steels
Low alloy steels
Lead and lead alloys
Zinc and zinc alloys
Magnesium and its alloys
Group 2 – Moderate attack
Copper and its alloys (but see section 5 below)
Group 3 – Very slight attack
Aluminium and its low strength alloys; slightly greater for Al-Cu and Al-Zn alloys
Nickel
Group 4 – Insignificant attack
Austenitic stainless steel
Chromium
Gold
Molybdenum
Silver
Tin
Titanium and its alloys
"
« Last Edit: February 17, 2024, 06:02:37 PM by mChavez »
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Wooden action & axles re-build
« Reply #16 on: February 17, 2024, 09:29:41 PM »

A number of bike shops are also willing to give scrap spokes from wheel disposal, it's always worth checking. A single DT Swiss spoke would be probably like, at most $2 USD. So if you have ti, why not use it. But if you want stainless, it's def an option. I embed the stainless spokes in wood handles of different varieties and haven't had any issues with chemical reactions, if that's worth anything. I've had one tool I made with a maple handle and stainless spoke under constant use for the past 13 years and it's still going strong. Hope that helps  in some way!
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Wooden action & axles re-build
« Reply #17 on: February 17, 2024, 10:41:03 PM »

I embed the stainless spokes in wood handles.....
I've had one tool I made with a maple handle and stainless spoke under constant use for the past 13 years...
What do you use it for?
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Wooden action & axles re-build
« Reply #18 on: February 18, 2024, 01:49:05 AM »

Not to digress too much from the thread but for the sake of the detail, I make very very small knives of various profiles and shapes as tools for my work, which is ocarina making. Few things are small enough to carve voicings and chamfers into delicate sections of wet clay, so I had to make these tools to do the job. They are frequently exposed to moisture so they had to be of a material that would be able to resist corrosion from the moisture and salts in the clay bodies while maintaining a decent sharp edge.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Wooden action & axles re-build
« Reply #19 on: February 18, 2024, 08:03:59 AM »

A number of bike shops are also willing to give scrap spokes from wheel disposal, it's always worth checking. Said Ross.
Absolutely. There's a specialist wheel builder in a farm building near me and I called in to try and find an axle for a one row and stuff for conrods. Maybe a dozen or so.
I came away with two handfulls, as much as I I could pick up. Obviously they need careful checking for parallel or tapered but this little pile will keep me going for ages.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal