Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Rigoletto One Row Melodeon - "D" - repair.  (Read 1208 times)

0 Members and 1 Guest are viewing this topic.

Christian E

  • Beloved Rat
  • Member
  • *
  • Offline Offline
  • Posts: 26
Rigoletto One Row Melodeon - "D" - repair.
« on: February 26, 2024, 07:47:02 AM »

Well, the MADness has begun.  I have a second box.

 I bought it off a charity site for very little, key unknown.  A "Rigoletto - Made In Germany US Zone" one row, two stop, melodeon.  It turns out that it's in "D", which is handy. 

A couple of the reeds are rattling, and scratchy sounding, and I'm not sure yet what to do about that, but I will learn! I will fix it! 

It overall sounds pretty good?  The bellows may leak some but it's so small that doesn't seem to make a huge difference? But the main leak seems to be from a weak spring on the air button, and a poor seal on the same. 

It's welcome any advice from the experienced people here. I figured this one was a good place to start, and as it came from Arizona, it's not musty or damaged by humidity.

I'll post more as I go further along, but here's a picture of the new baby melodeon. I think it's cute.

Logged
Irish B/C, so far.  That's it.  Wait, aw, there's a little baby one row melodeon now, too.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Rigoletto One Row Melodeon - "D" - repair.
« Reply #1 on: February 28, 2024, 10:31:02 AM »

Congrats.

Something this old will probably need to be re-valved, which might remove unwanted noises when playing.

If you hear a reed clipping the sides of its slot, then you can try:
1) If it's misaligned, very carefully, without damaging the reed tongue, turn it in its slot. If the reed turns easily, a kiss with a tack hammer on the rivet will tighten it, but if you have never done riveting before, I recommend practicing on a scrap piece first, as hitting the rivet too much can make things a lot worse.
2) very carefully running a stanley blade along the slot's side where the reed is clipping (just scrape the top corner of the slot, no need to scrape the full plate thickness) - this will scrape off a tiny amount of aluminium and the reed will be free again. We're talking about removing half a hair's thickness, not 1-2mm  >:E

Have fun!
Logged

Christian E

  • Beloved Rat
  • Member
  • *
  • Offline Offline
  • Posts: 26
Re: Rigoletto One Row Melodeon - "D" - repair.
« Reply #2 on: March 05, 2024, 05:57:42 AM »

Thanks, I somehow missed your reply.  I appreciate it!
Logged
Irish B/C, so far.  That's it.  Wait, aw, there's a little baby one row melodeon now, too.

Jérôme Croteau

  • New Starter
  • Offline Offline
  • Posts: 2
Re: Rigoletto One Row Melodeon - "D" - repair.
« Reply #3 on: March 06, 2025, 07:49:02 PM »

One year later, you still have it?

I just got one, two stops, in D as well, in near perfect condition, like it was never played before.

I had a few notes sounding when pushing on the bellows. I slightly bent the rods so the pallets sat perfectly but if i push hard, i still get sound... I think the springs are weak.

I'll open it open later this week, a few notes need to be tuned.

This thing is so small, I will need some time to adapt to it. On the bright side I think I'll pack it in my carry-on next time I travel as I will still have plenty of room left for other stuff!



Logged

Jérôme Croteau

  • New Starter
  • Offline Offline
  • Posts: 2
Re: Rigoletto One Row Melodeon - "D" - repair.
« Reply #4 on: March 06, 2025, 10:14:47 PM »

Side by side with my two row Hohner.  ;)
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal