Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: worn wood around buttons  (Read 1074 times)

0 Members and 1 Guest are viewing this topic.

David Martin

  • Member
  • *
  • Offline Offline
  • Posts: 5
worn wood around buttons
« on: March 22, 2024, 07:17:51 PM »

What can be done about this?

Pokerworks with the wood totally gone around the middle buttons
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: worn wood around buttons
« Reply #1 on: March 22, 2024, 07:49:50 PM »

1- Partial surgery to replace missing bits
2- Reface keyboard
3- Replace keyboard
(4- Replace Pokerwork !  ;D )
Logged

David Martin

  • Member
  • *
  • Offline Offline
  • Posts: 5
Re: worn wood around buttons
« Reply #2 on: March 22, 2024, 07:57:17 PM »



Are wood fingerboard replacements available or do the plastic ones fit an older box ?
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: worn wood around buttons
« Reply #3 on: March 22, 2024, 08:03:56 PM »

You can fill in the spaces with wood filler.
It's not ideal, but when sanded and painted, it can look OK.
I've done it and it works.
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: worn wood around buttons
« Reply #4 on: March 22, 2024, 09:08:37 PM »

I have developed an alternative to repairs or full replacement of broken Hohner keyboard tops that maintains the original wood. It is a flat machined panel with 21 slots (not holes but slots like the original) and 4 countersunk screw holes. I made a milling fixture to hold either 1/8" thick or 1/16" thick aluminum extrusions by the edges. A large CNC machine was used for accurate repeatable machining. A special round-over bit was purchased to put a small radius on the full perimeter of each slot and also on the machined ends of the extrusion. The extruding process itself provides a small radius on the long edges. This radius provides a nice comfortable edge so the fingers aren't going across a sharp corner.

It is discussed in detail here with photos:

https://forum.melodeon.net/index.php?topic=25858.msg308136#msg308136

With all the design time, fabrication, material and fixtures I am asking for $50 plus shipping. The first few folks can get one for $40 if you provide feedback to me on your installation experience.

Scott
« Last Edit: March 22, 2024, 09:12:59 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

David Martin

  • Member
  • *
  • Offline Offline
  • Posts: 5
Re: worn wood around buttons
« Reply #5 on: March 22, 2024, 09:50:57 PM »

Hi Scott

I think your method is really the answer. The wood is totally gone on about the middle 5 or 6 buttons but there is plenty left to support the plate.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: worn wood around buttons
« Reply #6 on: March 23, 2024, 12:12:39 AM »

Beats my method, and then some!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal