Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Converting chromatic bayan basses?  (Read 940 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Converting chromatic bayan basses?
« on: April 08, 2024, 03:08:54 PM »

Hi all,

Potentially, a very dumb idea, but have any of you had any luck converting chromatic bayan basses?

I've got a bass reed plate from a broken old Soviet high-end bayan. Here's a photo comparing them monsters to an equivalent oversized Hohner bass reed (which is already about 1cm longer and 1mm wider than the Italian stuff!). These are very high quality and very tightly fitted to the slots.

I've got 12 unisonoric reed pairs on a plate. I'm considering sawing off 3 pairs (so I can fit them into a ~36cm-tall box), leaving me with 9 to be potentially converted into some diatonic 18 bass system. Helikon bass meets the modern bass layout sort of thing.

The reeds are arranged in descending semitones and will most certainly require brazing on brass weights...But surely, even if I drop half of them by a quint, they should still perform better than a typical bass reed?

Any thoughts? I'd hate to ruin such nice reeds, but at the same time these are just too big to fit into any box as is without major surgery.

I haven't done any reed brazing yet, and have no idea how much weight needs to be added. Have some old lead sinkers as well, which will have higher density than brass if I was to mould them into squares, but I'd rather avoid having anything to do with lead fumes for obvious reasons.

« Last Edit: April 08, 2024, 03:13:10 PM by mChavez »
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Converting chromatic bayan basses?
« Reply #1 on: April 08, 2024, 03:35:09 PM »

What note and octave is the far left reed, please?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Converting chromatic bayan basses?
« Reply #2 on: April 08, 2024, 04:19:37 PM »

The Lowest note is E1 (41hz). I've got 4 plates for 4 octaves, but I'm not sure if the two higher octaves can be converted. 1.5 lowest octaves have weights/full thickness tips, while the rest are naturally sized.
Db (69hz) reed pictured in the first post.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting chromatic bayan basses?
« Reply #3 on: April 08, 2024, 05:00:41 PM »

Brass tip weights are usually attached with soft solder 60/40 tin/lead.  Soft solder temperature is below the critical temperature so you won’t soften the steel. Most of the reeds have substantial weights already, so do as much as possible of your tuning by filling those weights to raise their pitch.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Converting chromatic bayan basses?
« Reply #4 on: April 08, 2024, 06:03:35 PM »

Thank you.

Is it usually possible to de-solder the brass tips? I've got a decent modern temp-controlled soldering iron. This way I can see where the reeds fall naturally without a lot of filing, and it's reversible.

The second octave up only has 6 with non-filed tips, so the notes will need some planning, but I'm still assessing the feasibility of the whole thing.

Here's the 2nd octave:
« Last Edit: April 08, 2024, 07:47:16 PM by mChavez »
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Converting chromatic bayan basses?
« Reply #5 on: April 08, 2024, 06:58:16 PM »

My experience is that getting brass weights off is v easy. Just heat it with a soldering iron. Putting them back on is a different matter and can be tricky, though I have in the past made little brass weights from sheet brass and soldered them onto big reeds. You can pile quite a lot of solder onto the end of a reed and some bass reeds are weighted this way, rather than with brass (though you need to check the reed performance if you've put a lot of weight on there).
« Last Edit: April 09, 2024, 07:41:27 AM by Rog »
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal