Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tuning high reversed reeds  (Read 1279 times)

0 Members and 1 Guest are viewing this topic.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Tuning high reversed reeds
« on: April 09, 2024, 09:41:19 AM »

I think I now have the hang of tuning reeds in the rivet down, tongue up position. Then scratching and filing then checking gaps and valves.
On 4 stops where the reedblocks are fitted permanently I note that the little reeds are all waxed in with the tongues accessible like all the others which make sense as the working space is ridiculously small.
On 2 rows the top reeds are often fitted with the rivet ends upwards and the tongues pointing away.
A couple of questions
Why are they fitted like this when 4 stops aren't?
How do you tune them without taking the blocks out?
I confess I take the blocks out and tune these on the tuning bench and I know there must be a faster way. Im reasonably quick doing the rest but these reeds really slow me down.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Tuning high reversed reeds
« Reply #1 on: April 09, 2024, 06:18:06 PM »

In fact the high reeds don't drift that much in/out of the box. But …tape off the tremolo reed, measure the concert reeds in the box (write it down), remove blocks, shift pitch by the required offset on the tuning table, check in the box, then tune the tremolo on the tuning table by listening to the beats..(you don't really need to know the reading except to ensure it's sharper). This does work as an approach and I get v accurate results. And I've done it on lots of PAs where they have a lot more reeds than melodeons ( PAs often have coupler buttons so I can isolate the concert reed without resorting to tape). Others may approach it differently.
« Last Edit: April 09, 2024, 06:27:16 PM by Rog »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Tuning high reversed reeds
« Reply #2 on: April 09, 2024, 09:58:48 PM »

To answer one of your questions, Hohner button boxes generally have all their reeds -including those high notes - oriented upright, whether in a 4-stop with blocks glued in place or in a 2-row with removeable blocks.  I'll only flip those highest reeds if I can't them speaking adequately otherwise.

Also generally speaking, those highest-pitched reeds do tend to respond better when oriented upside-down.  This does make them a bit of a pain to tune, as you've noticed.  The biggest issue is when trying to raise the pitch of the inside reed.  Bending those tiny reeds - regardless of reedplate orientation - through their opening can easily distort them and cause problems with how they respond.  In these cases, I just take the plates out of the wax and raise the pitch on both sides (if needed) and then wax them back in.  It's then much easier to lower the pitch a little as needed with the blocks in-situ. 

As Roger said, if needed, you can take the blocks out and measure the tuning on a tuning table and 'do the math' compared to their pitch when in-situ.  That's the only instance where I will do any tuning on reeds on blocks outside of the instrument.  It can take me just as long to tune those few, pesky piccollo reeds - and get them to respond optimally - as it would to tune the rest of the bloody block!
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning high reversed reeds
« Reply #3 on: April 09, 2024, 10:06:36 PM »

My method is to tune the reversed reeds about 5 cents sharp while the block is outside, it’s usually possible to tune them down to the correct pitch with the blocks in situ.  You have to go very carefully so you don’t  go too far and have to take the block out again!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

komat

  • Eastcoaster
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 228
Re: Tuning high reversed reeds
« Reply #4 on: April 10, 2024, 03:03:39 AM »

My method is to tune the reversed reeds about 5 cents sharp while the block is outside, it’s usually possible to tune them down to the correct pitch with the blocks in situ.  You have to go very carefully so you don’t  go too far and have to take the block out again!

Came here to say the exact same thing!
Logged
Too many accordions, help!

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Tuning high reversed reeds
« Reply #5 on: April 10, 2024, 08:41:37 AM »

As I think was mentioned on another thread, you can use a scraper on the tip of tiny reeds (supported obvs) to sharpen them.

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Tuning high reversed reeds
« Reply #6 on: April 10, 2024, 09:23:45 AM »

Ok thanks.
That's basically what I've been doing but I was sure someone had a better method.
I'm just happy HA114 reeds aren't reversed. That would be an excellent case for launching melodeons out of the window.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Tuning high reversed reeds
« Reply #7 on: April 10, 2024, 09:24:45 AM »

Don't tune them, pal. Nobody plays them squeaky notes anyway  >:E

On a serious note, you can buy a TCT CNC engraving bit and improvise a handle for it. It will be very thin and very sharp, which allows you to effortlessly make small scratches for fine tuning these buggers.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal