Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Thirds stop reed block set-up?  (Read 2749 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Thirds stop reed block set-up?
« on: May 03, 2024, 10:05:49 AM »

Hi All,

I am wondering about the voice & reedblock set-up in boxes with a thirds stop. Perhaps, somebody can share a photo/explanation/layout?

I understand the "classic" 5-voice bass machine set-up very well, where you get 2 voices for the bass and 3 for the chords. The chord button plays 3 voices at a time, the bass plays all 5, with the two lower octaves providing the oomph. But I don't see how a thirds stop can be implemented in this set-up because to allow a 5-voice bass machine, the reeds need to be shared between the chords - the plate with the third is not always a third for every chord.

Looking at castagnari handry 18, there's 9 basses and 9 maj/min chords packed into a very small box + a thirds stop - how do they do it?

Thank you.

Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Thirds stop reed block set-up?
« Reply #1 on: May 03, 2024, 10:33:17 AM »

Not sure I understand "the bass plays all 5".

For instance a typical G bass and chord would have the following reeds
L and M G reeds for the bass
G, B and D in the chord
If the bass button played all 5 you would get G in 3 probably octaves but with a B and a D as well which would be odd

The boxes I met with shared reeds in the bass only play the, in this example, G from the chord and do not sound the B or the D. This allows for a third stop as it only affects the B

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Thirds stop reed block set-up?
« Reply #2 on: May 03, 2024, 10:40:21 AM »

[Replace 5 with 4 for 4-voice boxes]

In a typical bass machine set-up there's 5 voices (reed banks), with two pallets: one for the two lowest octaves, and one for the 3 highest.
Bass button typically lifts both pallets via a linkage, so plays the note in 5 octaves.
A chord button only lifts one pallet for the 3 highest octaves, but the bass machine roller mech connects 3 (rarely, 4) pallets to a chord button, so you get your root, fifth, maj/min third, 7th, dim selection.
You get 3x3=9 reeds playing the chord.

I can see how the system you describe for a G button will work with a thirds step, but that's only a single-voice chord (3 reeds only)  (and only a single-voice fifth with the stop engaged - that's two reeds).
« Last Edit: May 03, 2024, 10:42:34 AM by mChavez »
Logged

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Thirds stop reed block set-up?
« Reply #3 on: May 03, 2024, 02:41:53 PM »

What kind of instruments have you been looking in?

The fundamental buttons on all my instruments do not play any of the other notes in the triad. The level of complexity in melodeons is typically very low, typically with no reed sharing between chords. The usual answer is, lots of big palette with dedicated reeds.

Also, isn't the handry is huge? Rather than very small? Perplexing.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Thirds stop reed block set-up?
« Reply #4 on: May 03, 2024, 02:59:36 PM »

Fundamental never plays anything but the fundamental, but it plays it in all octaves.

I've been playing a CBA before diatonics, and right now I've got two Hohner Morinos and an old Hohner 235 that needs an overhaul. All of these diatonics follow the same principle as accordion bass machines.

So yeah, Handry's small  ;)

In any case, Handry website claims it to be a 3-voice 18-button bass in a box that is an inch shorter than the bigger Club boxes with 8-12 basses. As far as I understand it. I thought that maybe there's some very smart way of arranging basses for the thirds switch.

If chords are single-voice, then it all makes sense - thirds come out to a separate reed block & bob's my uncle. But I expect that will get completely drowned out by MMM or LMMM melody with the thirds stop engaged (3-4 reeds melody vs 2 reeds chord).
Logged

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Thirds stop reed block set-up?
« Reply #5 on: May 03, 2024, 06:06:25 PM »

Yeah no anything with a bass machine or fancy pants reed sharing isn't really going to work with a thirds stop implemented by a slide. It also probably shouldn't need it either since you just add whatever chord it is you want?

The diatonic instruments which push/pull changing chords don't work like that and typically can't work like that, as you need a plate that's D one way and E the other for one set, and can't really share with one that wants D one way and C the other. So they have dedicated groups of chords, with therefore a lot of redundancy, and way less stuff in way so they're plenty loud. As a result, they could have specific plates with just the thirds in for that specific button and the slide can just shut those ones off without having to worry about needing that specific d# in some other chord - because it will have its own separate d#.

You can see some pictures and people talking about thirds stop stuff in probably a few places but in particular in this thread I made a few years ago of me slowly figuring out how to add one to an instrument: https://forum.melodeon.net/index.php?topic=22920.0
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Thirds stop reed block set-up?
« Reply #6 on: May 03, 2024, 06:19:45 PM »

Here are a couple of pictures of a Handry bass-side internals (from this site https://www.mon-accordeon.com/occasion/d0378-castagnari-handry-18-cassotto )

The reeds for each of the 9 bass/chord button pairs are aligned 'across the blocks'. From back to front, they seem to go:

block 1: high bass, low bass (with slide to remove low bass)
block 2: 2 chord notes, tonic (also played by bass button) and removable third (notice slide)
block 3: 1 chord note, fifth
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Thirds stop reed block set-up?
« Reply #7 on: May 03, 2024, 06:33:30 PM »

There are many different setups for the reeds and mechanisms in melodeons.  The big Hohner Club systems sometime do have reed sharing between different chords,  and reed sharing between bass and chord is common but not universal.

The way I would decide if a thirds stop could be fitted is to plot out the location and pitch of every reed in the bass end.  One convenient way of doing this is to place a strip of masking tape along the top of each block and then write all the note names on the tape. Then you can also annotate to identify the location of tonic third and fifths.  With Hohners you will often find single reed plates with third on one direction and fifth on the other.  That means there’s no easy way to add a thirds stop.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Thirds stop reed block set-up?
« Reply #8 on: May 03, 2024, 07:16:55 PM »

I tried to find a way to have a 3rds stop on a 4 note bass/4 note chord system.
In the end I replaced 3rds with 5ths to give a really full sound and retain the 4 note chord.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Thirds stop reed block set-up?
« Reply #9 on: May 03, 2024, 07:39:40 PM »

Thanks all.

With Hohners, yes, it's not possible to add a stop on the Morino or 235. Easier to add buttons - at least that's what I want to attempt.

One of the reasons I'm asking is because I'm breaking down a cba, and have a nice aluminium drop-in bass fondo, so I was thinking about designing my own bass end. Hacksawing the 12-note fondo to 9 notes pretty much produces a copy of what's in the Handry.

The 3-voice-bass Handry comment got me confused, thinking there's a magic formula - now I can see it's a 3-voice bass with a 1-voice chord.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Thirds stop reed block set-up?
« Reply #10 on: May 03, 2024, 07:58:38 PM »

I ended up making new bass end reedblocks so I could have a 3rds stop on this project 3M about â…“ of the way through the thread.
I can take some more pictures if it would help
https://forum.melodeon.net/index.php?topic=25468.0
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Thirds stop reed block set-up?
« Reply #11 on: May 03, 2024, 08:09:17 PM »

Thanks.
The beauty of this cba fondo is that the whole assembly can be just lifted from one box and screwed into another without too much fannying about.
I'm right in the middle of another project right now, so this is just me thinking ahead.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Thirds stop reed block set-up?
« Reply #12 on: May 08, 2024, 08:43:33 AM »

@tirpous

Re-reading your comment, it looks like Castagnari use a standard accordion fondo & register mech (sized to 9 notes instead of 12), but the bass machine must be more complex.

In an accordion there's usually 2 pallets for each note. one responsible for 2 large bass reeds, and another one responsible for 3 chord reeds.
If I understand correctly, there has to be 3 sets of pallets in castagnari. Per description:

Rows 1&2: Two lowest bass reeds
Row 3: tonic
Rows 4&5: Third & Fifth.

The row 3 pallet must be hooked up to both fundamental & chord buttons via a linkage if it is to be operated by both?

Does anyone have a photo of the bass machine? I'm quite curious how it looks.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Thirds stop reed block set-up?
« Reply #13 on: May 10, 2024, 08:35:38 AM »

https://forum.melodeon.net/index.php?topic=17858.0

Found the answer. Shared pallet.
Probably too much work to butcher the existing 2-pallet set-up. I can still use the accordion fondo as-is, but it will be 2-voice bass + 1-voice (3 reed)  chord.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal