Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Yet another button height question  (Read 2198 times)

0 Members and 1 Guest are viewing this topic.

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Yet another button height question
« on: June 04, 2024, 12:14:59 AM »

I'm hotrodding my C#/D Hohner (thank you, Lester).  I'm at the point where I need to choose a button height.  In his video, Lester starts at about 1/4 inch above the keyboard, then bends them back down a bit.  Having no playing experience, can anybody tell me what a good final height is?  4mm?  4.5?   I'd like to know what to aim for before I start bending stuff. 

(The answer is probably here somewhere, but there were too many search results.)
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Yet another button height question
« Reply #1 on: June 04, 2024, 01:44:17 AM »

It's definitely a matter of personal preference, so you'll have to decide for yourself what feels right. That being said, it's easy to set them up to a nice even height and adjust down like Lester shows. I use a hook tool to grab the lever and lift it for raising and just hold the lever and press the button for lowering. Most people like the buttons to end up being flush with the board when depressed.

good luck with the hot rod!!
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Yet another button height question
« Reply #2 on: June 04, 2024, 04:57:00 AM »

4 or 4.5 mm should be fine as a target height to get going. Semi-tone playing technique includes sliding from a button to the next, so you definitely don't want them too high. The actual feel will not only depend on height but also the shape of the buttons (flatish top with sharp edge vs crowned top and radiused edge, Hohner buttons are not always the same) and key travel limit being implemented or not. You can always readjust later as you get more experience.   
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Yet another button height question
« Reply #3 on: June 04, 2024, 08:54:32 AM »

I agree with tirpous, sliding is part of the technique. I play a B/C salterelle bouebe it's about 3.5mm with a crowned top and radiused edge. Recently I tried a Castagnari Dinn and found it difficult to play, the buttons were only very slightly higher. I think button height, shape and distance apart make all the difference.
Logged

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Yet another button height question
« Reply #4 on: June 05, 2024, 03:15:54 PM »

Thanks, guys.  I started adjusting the height.  Now I notice that some buttons have been replaced, resulting a mix of flat tops and crowned tops, in no particular order.  Looks like one more thing to address.
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Yet another button height question
« Reply #5 on: June 05, 2024, 04:59:56 PM »

Thanks, guys.  I started adjusting the height.  Now I notice that some buttons have been replaced, resulting a mix of flat tops and crowned tops, in no particular order.  Looks like one more thing to address.

That's more Rat Rod than Hot Rod ;D
Logged

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Yet another button height question
« Reply #6 on: June 06, 2024, 12:30:39 AM »

Sounds about right.  Of course, nobody said I had to confine my endeavors only to hotrodding.  ;)
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Yet another button height question
« Reply #7 on: June 07, 2024, 05:44:48 PM »

Are you folks talking about flat keyboards or stepped keyboards?

What's a good stepped button travel for a melodeon? I am currently aiming for 5mm travel without padding and need to decide on 2mm felt vs 1mm felt lining.
I am guessing that 1 is the way to go, unless 2mm will compress after a couple of months and end up being a better option?
Logged

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Yet another button height question
« Reply #8 on: June 09, 2024, 01:39:26 PM »

Are you folks talking about flat keyboards or stepped keyboards?

What's a good stepped button travel for a melodeon? I am currently aiming for 5mm travel without padding and need to decide on 2mm felt vs 1mm felt lining.
I am guessing that 1 is the way to go, unless 2mm will compress after a couple of months and end up being a better option?
My keyboard is flat.  I will attempt to answer your questions with my rudimentary knowledge.

First, stepped versus flat should require the same approach.  Set the button height where you want it, then set the travel limit where you want it.  If the depressing action between the rows is significantly different, you can limit the travel of each row separately.  I have seen a video or pictures of this, so I know it can be done.

Regarding felt, yes, you will get some sponginess, and some compression over time.  The latter should be a reasonable amount, unless you play like a gorilla.   ;) (all musical instruments should be played with a light touch, tension and strength are our enemies)  Due to the compressability of felt, including liking a positive, definite stop, many folks have opted to use wood instead of felt.  Or wood plus a thin layer of felt. 

Personally, I will try to use wood + thin felt if the construction of my keyboard allows.  We will have to see.

My thanks to all the fine folks here who have shared their knowledge and allowed me to have at least a basic understanding through studying here.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Yet another button height question
« Reply #9 on: June 09, 2024, 01:50:20 PM »

Are you folks talking about flat keyboards or stepped keyboards?

What's a good stepped button travel for a melodeon? I am currently aiming for 5mm travel without padding and need to decide on 2mm felt vs 1mm felt lining.
I am guessing that 1 is the way to go, unless 2mm will compress after a couple of months and end up being a better option?
Your finger is made of soft tissue and hard tissue. Between initial contact with your finger and the key starting to depress you probably have more than  1mm compression in your soft tissue (unless you have high blood pressure- but let's not go there). I would go for 1mm as that seems to be closer to where the older open top keyboards I personally have seen started out.
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Yet another button height question
« Reply #10 on: June 09, 2024, 01:55:36 PM »

Thank you.
I'm not sure that flat vs stepped is the same approach though!

For example, my "flat" Hohners are set up at button height of, say, 3.5mm. I am, however, not sure how deep the buttons go below the flat surface before they come to rest on the stop. Could be -0.5mm, could be -1mm. Even if they go down -1.5, -2mm when measuring, there's no guarantee that I bottom them out when playing. So for practical purposes I'd really struggle to tell you what button travel I have on my flat keyboards.
I reckon you can get away with more on a flat keyboard, because on the stepped keyboard the stop is more abrupt. Flat keyboards' felt can be 4-5mm thick, giving a very nice cushion. Or they can have no stop at all and they are still very playable, albeit, a well-placed stop feels nicer.
For stepped you're using 1-3mm and there is no key guard to stop your finger - you're relying entirely on the felts.

I've set the buttons at 5mm and tried quickly inserting 2mm and 1mm felts under them without gluing them on. 1mm felt better, 2mm felt a bit spongy. But will it feel better in a year's time once it has compressed...

Agree about tension - I've set ~120g across the whole keyboard and it plays beautifully.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Yet another button height question
« Reply #11 on: June 09, 2024, 05:16:59 PM »

Just had a look at my Vienna Type A&D International.
Step in the keyboard is 7mm. The MoP buttons are screwed through a thin felt pad onto the top of the key lever.
So when the outer keys are set to lie flush with the upper deck of the keyboard they have 7mm travel before bottoming out.
Interestingly 7mm at outer rim of key = 5mm at the step.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal