Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: I keep breaking spoon bass springs!  (Read 1290 times)

0 Members and 1 Guest are viewing this topic.

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
I keep breaking spoon bass springs!
« on: July 04, 2024, 09:14:26 PM »

I've now broken a fourth spoon bass spring on my Hohner HA-114. One of them one even a recently purchased replacement from Charlie Marshall!

First, is there anything I'm doing wrong that's making the springs wear faster? Do I need to be cautious about not letting the spoon snap shut?

Second, has anyone successfully repaired a spoon bass with a new spring? How do you replace the rivet? What kind of wire do you use for the spring?

Third, with Charlie Marshall having shut up shop, where can I get replacement spoons? Apparently, I need to lay in a large supply. Even better if someone knows a source in the States.

Thanks! It really takes the wind right out of one's sails to be in the middle of a spirited slip jig and suddenly feel the bass spoon go slack under your finger. :(
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: I keep breaking spoon bass springs!
« Reply #1 on: July 04, 2024, 10:40:52 PM »

No need to replace the spoons, only the springs themselves, which admittedly takes a bit of work to get at.  You have to cut off one end of the pin to be able to pull it out and gain access to the spring. I used to just make new springs out of safety pins, then re-installed them using a cotter pin in place of the original pin.  You have to bend the one end of the cotter pin afterwards to prevent it from slipping out.  I'm sure there are better options for replacement pins, but this has worked fine for me.

And yes, it's a drag when those spoon springs break.  It's actually quite common.  You're not doing anything wrong; the original Hohner parts are just junk.  I've yet to break one of my homemade 'springs'.

Logged
C#/D player

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: I keep breaking spoon bass springs!
« Reply #2 on: July 04, 2024, 10:47:12 PM »

If you are in UK , I can send you a few springs and some nails which match the rivet size.
I did a rambling video on YouTube how to do it.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: I keep breaking spoon bass springs!
« Reply #3 on: July 04, 2024, 11:47:16 PM »

My pin replacement is to use a brass picture hanging pin, cut and file it to be a flat nosed pin a couple of millimetres longer than the the old rivet, I notch the pin with a junior hacksaw blade to create a seating for the trunnion and when I push the pin in turn it with pliers so that the spring loop bearing on the pin keeps it in place.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: I keep breaking spoon bass springs!
« Reply #4 on: July 05, 2024, 06:58:15 AM »

I use piano wire to make springs (i have a couple of gauges). You can get it on eBay. You could try guitar string wire too. Safety pins aren't made of spring steel afaict.

Mike Hirst

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1433
  • Black Dot B/C, Bastardo C#/D, Corona II GCF
Re: I keep breaking spoon bass springs!
« Reply #5 on: July 05, 2024, 10:29:22 AM »

Safety pins aren't made of spring steel afaict.

For many years I used safety pins to repair broken spoon bass springs. Although they are not made using sprung steel they can be used to make a serviceable and successful permanent repair. The trick is to double wind the pin.

With pliers carefully remove the head of the pin. Do not cut the wire. This will give you some extra length. Straighten the wire, then using a nail to hold the spring end add an extra turn. This will give sufficient resistance to make the repair work.

Removing the pivot is a bit tricky. Use a file to remove the end, on either side, then you can slide the rest out and remove the broken spring. Fix the new spring in place using either a split pin or a bifurcated rivet.

For a less invasive safety pin repair that does not involve removing the rivet see p15 in Tufty Swift's Hints On Playing One Row Melodeon.
Logged
Semper idem, sed non eodem modo

Arnold

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
Re: I keep breaking spoon bass springs!
« Reply #6 on: July 05, 2024, 09:10:46 PM »

I received a box with a broken spring and performed the repair using the safety pin method described above. Getting the pin out is a right pain. I eventually managed with side cutters, but that’s just what I had to hand… On my HA112 I put cork under the spoons, the idea being to reduce maximum possible stress on the spring, so less likely to break…
Logged
Dancing about architecture since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal