Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Adding a register stop  (Read 1919 times)

0 Members and 1 Guest are viewing this topic.

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Adding a register stop
« on: July 07, 2024, 01:25:10 PM »

Hi all,

I am doing some wild squeezebox butchery, and considering adding a register stop.
The box came as MMH without registers, which was a bit squeaky to begin with. I've counted 20 broken reeds in the box, mainly H voice (every time a reed would break, the previous owner would put some gaffer tape over the slot and keep on playing  :||:), but with some cross-voice cannibalisation and fettling I've ended up with two full M voices and almost no H left. I do have a spare set of L voices, so I took the ruler out and started measuring. The H block is shared between two rows of pallets, so I just need to make one new reed block for L instead and add a stop. If I shave off some excess wood from the tallest bass reed block and do some filing of the tallest L reed plates, I can just about fit the L voice, but my new reedblock base is limited to 4mm max. Ideally, I'd go for 3mm, but I don't think that's feasible if I'm routing it for a slider?

So the plan is:
- Laser a register slider in 2mm plywood.
- Laser the reed block sole with a matching soundhole pattern from 4mm ply
- Laser the rest of the block to fit the new reeds
- Rout a slot in the sole for a tight fit for the slider
- Drill a 3mm (4mm?) hole in the top of the box to fit the stop rod.

Questions to folks who have done this before:
- Is plywood a suitable material for register sliders and routed-out reedblock sole? I can do hardwood instead (beech, maple) but I'm not sure my laser guy can laser that without burning the wood. If I drill, I'm not 100% certain I have enough space for round soundholes (laser can do square shapes). Would ply-on-ply contact between the slider & the sole work?
- There's plenty of info on adding stops, but I haven't seen the info on adding bushings for the stop rod - any suggestions? And how do I minimise the air leakage?
- I've read that some of you use magnets to help keep the stop in the up position. If it just the case of getting a couple tiny rare earth magnets and finding a place where I can fit them?
- Is it usual to have stop "in" (i.e. pressed down) to activate the voice or to switch it off?

Thank you.

Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Adding a register stop
« Reply #1 on: July 07, 2024, 07:41:58 PM »

I use 1.5mm aircraft quality plywood for stop slides. It works well, ply on ply is fine.

You could bush the stop-rods with Teflon or something similar.
The usual method is to place a soft leather washer on the inside and outside portions of the stop-rod.

Small rare earth magnets are ideal for this job. They work best with mild steel stop rods.

Normally it's stop in to switch the voice off but the other way around is common too, e,g. Saltarelle.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Adding a register stop
« Reply #2 on: July 07, 2024, 07:49:14 PM »

Thank you very much.
And do you rout the reedblock base to ~1.5mm depth for the slider channel, or do you glue the base up with 1.5mm ply "feet" so the slider can fit between them?

And a follow-up thought: does the ply slider rest on the ply fondo? usually there's a gasket between the reed block sole & the fondo, but I can't see the slider working well if it sits on the gasket, as it will be catching the exposed gasket edges around soundholes? Or is it a sandwich of ply base routed to house the slider, and then a lid that rests on the gasket, like you see in old hohners with metal sliders?
« Last Edit: July 07, 2024, 08:15:57 PM by mChavez »
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Adding a register stop
« Reply #3 on: July 07, 2024, 10:10:23 PM »

I've done it both ways.- - router channel or built up feet, both work well.

Many Italian boxes have the slider sitting against a gasket. I've not seen any problems with this setup.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Adding a register stop
« Reply #4 on: July 08, 2024, 07:01:59 AM »

Thank you.

I have discovered a new problem while measuring things up: the original ply soundboard has warped quite a bit!  :-[ I guess this might still work with non-register blocks, but I don't think a slider will work here as is.
Are there easy ways to try and fix it in the box, or is this the case of replacing the fondo?

[img width= height= alt=PXL-20240707-193141097" border="0]https://i.ibb.co/Gk8fxhY/PXL-20240707-193141097.jpg[/img]
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Adding a register stop
« Reply #5 on: July 08, 2024, 11:13:52 AM »

I have managed to correct warping by adding a brace running the length of the reed blocks.  Though looking at your photo you might not have sufficient space.  My photo shows a two voice Club II with a brace next to the red block. The brace is glued in and screwed from the pallet side.  I used trial and error  to shape the surface of the brace to be very slightly concave so that the combination ended up with a flat fondo.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Adding a register stop
« Reply #6 on: July 08, 2024, 05:03:40 PM »

Thanks Theo.
That gave me an idea that I can re-glue some existing bracing around the fondo, but once I started picking it, I've realised how poorly made & glued that thing is (it's a soviet box), so ended up tearing it all out.
I'll treat it as a learning experience and get a new soundboard for it, but my new question is: is there any point in gluing the new soundboard, or can I get away with screwing it down + a bead of reed wax around it? I intend to glue significant bracing onto the "inside" of the fondo everywhere apart from the area with the reed blocks to minimise the chance of any future warping.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Adding a register stop
« Reply #7 on: July 08, 2024, 05:28:17 PM »

I don’t know the answer about screwing, but my guess would be that glue would be more secure.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Adding a register stop
« Reply #8 on: July 24, 2024, 10:00:01 AM »

Thank you very much for all the advice gents.

I regret to say, I chickened out of installing the register switch.  :-[
Designed a new soundboard, reed block, register sliders, assembled the block and then decided that this will be enough excitement for me for now, and I better quit while I'm ahead.
Therefore, it's a new soundboard, and permanent MM+H into permanent LMM+ conversion.

Looking at the sliders, there's not much sole left after I rout it out. The sliders need to be a tight fit, but what's going to happen when the humidity changes and wood starts expanding... Even if I put a double coat of shellac on them, which is the treatment I apply to all woodwork (still lets the wood "breathe" but at a slower rate than unfinished wood), there will be some movement.
Perhaps, a laser-cut alloy slider is the way to go (or simply sliders salvaged from an old box).

Next job is to install the soundboard and brace the dickens out of it to prevent future movement. What I might do, is rout out a slot for sliders in the brace at the chin end of the box, so if I decided to add a register switch in the future, it will be relatively straightforward to do if I make a new block.

PXL-20240724-084444616" border="0
PXL-20240724-084208531" border="0
PXL-20240722-180148057-1" border="0
« Last Edit: July 24, 2024, 10:02:12 AM by mChavez »
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal