Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Adding an automatic bass coupler  (Read 1011 times)

0 Members and 1 Guest are viewing this topic.

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Adding an automatic bass coupler
« on: July 09, 2024, 03:43:25 PM »

I've been daydreaming about possibilities recently, and I would love to be able to take my lowest bass reeds in and out while playing. The stop on the top is just too far away to reach mid-tune without more of a break in the melody than I would like (and my neck isn't long enough to chin it like I sometimes do with the treble stops).

Has anyone ever had an automatic coupler added to the bass end? Either something like the little buttons on the front of a Castagnari or a thumb switch that I vaguely recall seeing on someone's box. Is it even possible to do?
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: Adding an automatic bass coupler
« Reply #1 on: July 09, 2024, 05:05:14 PM »

A wee while ago on some forum I've read a similar question and somebody floated an idea of adding a wee servo motor to push the register slider on & off. Hooked up to a microcontroller & a switch anywhere on the melodeon. The advantages were that you do not need to make any major butchery - just use the existing register stops and add the servo on the inside. The challenge, from memory, was dealing with powering the microchip & the servo in a compact way.
I don't recall seeing the results of that experiment - perhaps, there's more to it than you see on the surface. Or maybe the power of the servo was not enough to shift that particular slider.

But it's an idea anyway, and it should be pretty much perfectly reversible if you find a way to feed the switch wire out of the box without making new holes in the woodwork. If the electronics fail, you still have the original manual stop.
« Last Edit: July 09, 2024, 05:11:55 PM by mChavez »
Logged

Andy Goldfinch

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 150
    • Andy Goldfinch Melodeon (YouTube)
Re: Adding an automatic bass coupler
« Reply #2 on: July 11, 2024, 09:38:51 AM »

That's an interesting idea, thanks, I hadn't thought of something electronic. I know you can buy automatic switch pressers for automating light switches and things, I wonder if something like that might work. I'll have to do some research.

I wonder if there are any more traditional, mechanical solutions though?
Logged
D/G Castagnari Dony, D/G Hohner Club VII (9 bass), D/G Serenellini Maestro, C/F Hohner Club II (DIY restoration in progress...)

https://www.youtube.com/@andymelodeon

JNM SY

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 227
Re: Adding an automatic bass coupler
« Reply #3 on: July 11, 2024, 08:07:34 PM »

Without knowing the make and model of box you plan to modify - if it already has a bass stop on the top the you should be able to attach a lever to the block of wood the top stop screws into, at right angles, and extend it so it comes out the bass plate ( avoiding, but close to, the air button).
 Pressing down with your thumb would be the same as pressing down on the top stop. The lever would have to be fairly rigid and possibly a zig-zag shape so it comes through the bass plate in the right place.
  You could make a trial version out of lighter wire first as a template.
 Good luck.
                       John.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal