Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Yet another Wax question  (Read 821 times)

0 Members and 1 Guest are viewing this topic.

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Yet another Wax question
« on: August 11, 2024, 04:21:48 PM »

Its obvious to me that when you have a situation where reeds are falling out and the wax on the blocks is dry and crumbly that you should replace the stuff and do a fresh job of installation.

What's not obvious to me is, if you're swapping a reed set out (same length of plates mind you) from a block you already waxed a year ago, should you scrape off all the still fresh wax or can you wax the new reeds in with much less new wax needed?

My gut reaction to that was 'no, probably not. The volatiles are spent, oil maybe altered, and the wax will probably not hold the same way once it's been re heated and re set again' but I'd figured I'd ask just to make sure. So, what do you folks do about this situation? Remove the year old wax and go at it fresh, or re use the older stuff without much issue? I'm not opposed to a little extra cleaning, I actually enjoy the scraping process, but I am curious indeed.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Yet another Wax question
« Reply #1 on: August 11, 2024, 04:54:35 PM »

I agree, but for a different reason.  If remnants of wax remain on the blocks (a) the new reeds may differ in size and if larger they will sit on top of the wax in places, and (b) having bits and pieces of wax on the blocks makes it harder to get a neat flow of wax round the reeds because you are waxing onto an uneven surface.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Yet another Wax question
« Reply #2 on: August 11, 2024, 06:28:35 PM »

Thanks for the reply, Theo. In this case, the reed plates are the same width and height (and some very very small differences in height), but still, the threat of an uneven surface is possible. I do wonder if folks have re used wax with success, and whether it has just proven to last less time over the years or not. Ive made up my mind to clean off the wax at this point since your vote, but I am still curious to see what people have done
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Yet another Wax question
« Reply #3 on: August 12, 2024, 03:54:46 AM »

I've done both in cases like what you're describing, but I've only reused some of the previous wax if:

a) the previous waxing job was done quite recently (you'll know right away if the wax is as good as new or if it's begun to dry out)

b) the old reedplates were carefully 'cut' out of the wax before removing them so as to avoid having strands of soft wax pulling away with them and making a mess

c) the new reedplates and reed tongues are generally the same size/length as those that were there before so that no modification to the reed chambers is required

Even in the above cases, I would have first re-melted the existing wax before applying a fresh layer.  Having said all that, I've found that it's generally easier (and safer) to just take the extra few minutes and scrape off the previous wax and start anew.  The biggest concern is having some of the previous wax end up on the underside of one of the reeds where you don't want it, fouling up a valve or whatever.  It's easy for that to happen if you're not being extremely careful...which is why it's just easier to do it again from scratch.  Scraping off new wax is not messy like old wax, so it's not a big deal.
« Last Edit: August 12, 2024, 04:07:20 AM by mselic »
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Yet another Wax question
« Reply #4 on: August 12, 2024, 04:05:32 AM »

Regarding longevity of wax...I've seen brand new instruments from Italy that had wax already drying out noticeably...and Hohners that were 50+ years old with the original wax that was still soft (re-melting it would be a different story, though...don't do that!).  I think overheating wax, whether in a pot or when using a soldering iron, can potentially affect the integrity/longevity of it, but I also think a lot of it has to do with the manufacturing of the reed wax in the first place.
Logged
C#/D player
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal