Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: High F# push reed difficulty sounding- voicing issue?  (Read 1849 times)

0 Members and 1 Guest are viewing this topic.

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
High F# push reed difficulty sounding- voicing issue?
« on: August 14, 2024, 10:01:55 PM »

So I've been having some complications with the smallest reed in my very small one row, only on the push. I know that setting the reed/voicing it is the most sensitive process, and that minute adjustments can be the difference between working or being dead silent. I had a C reed set in there before and it was a lot of fussing to get even a weak push out of that reed so I figured when I'd swap the reeds out after then surely the replacement fresh reed would have no problems at all.

But alas, the pull works splendidly but the push again does not. Every other reed id voiced well and tuned up without issue but that one F# is just refusing to sound.

I'm starting to wonder if the chamber is to blame here. I resized it a little to hopefully get better response from the reed but while the pull is fantastic, I can't get much but a strange distorted windy sound if I push quite firmly.

I also tried venting the chamber a bit by putting a tiny hole in the wax, attempted a valve on the outside, cut a bit off the top to see if that would help, nothing works.

I've played with the set multiple times and the best I can get is a faint, very quiet tone.

Any ideas? This Melodeon is very small, smaller than a lilly, so the pressure inside the box is a bit different than a conventional full sized accordion, but apart from the smallest F#, the rest of it plays beautifully.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #1 on: August 14, 2024, 11:06:02 PM »

Is the reedplate upside down? ( rivets end where vibrating end of reed usually is) This is a common fix for highest reeds.
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #2 on: August 15, 2024, 02:29:42 AM »

Yeah, I tried that, still no dice. If you pump the bellows quite firmly and you only have one voice selected you can get a faint tone, fleeting and almost imperceptible. Both voices selected you get nothing.

I should add that when pushing hard you can hear a sort of harmonic flipping that sounds like both push and pull reeds being activated in some way. Any idea what that's about?
Edit: thought maybe it indicated fouling of the reed against the frame but it plays nice and clear outside of the box just fine. When its back in the box it fails, just the F#. I'm perplexed

Edit!
Just discovered something that might give someone something to suggest. When I very very lightly depress the button for that F#, barely opening the lever, THEN the F# sounds! Both F#'s! So too much air being allowed to escape in a big rush is preventing it from sounding. Note, I cannot produce a tone from either reed with the pallet open, no matter how hard I push really, just a faint tone. But if Its nearly closed, I get a solid tone. What is the solution here?

Yet another edit:
I decreased the chamber size for the problematic reed and I got a usable tone! It's not particularly responsive and is rather quiet but now I bet if I change the set I'll get better results.
I think that the maker of this box didn't get the chamber balance of the reed block quite right and I suspect if I tweak the sizes of the 3 highest reed plates I'll get faster response from the things.
The D/B reed plate, next one down from the F#, is nice and zippy and clear which is interesting. I
« Last Edit: August 15, 2024, 05:16:49 AM by Ross Dubois »
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #3 on: August 15, 2024, 07:21:33 AM »

1) Gapping the smallest reeds is a bugger. Check & double check that it's set up correctly. If it plays outside the chamber just fine then the gap is probably OK.
2) Check that there's no leaks in the wax/gasket on the block. Even small hairline leaks can significantly slow down a small reed response.
3) Does the plate sound well in another reed chamber? It could be that the chamber is hitting the "dead" zone for that note and needs to be re-sized.
If you were struggling with a C reed, and now struggling with F# in the same chamber, then it's probably not the chamber size, as the "dead" zone will be frequency-specific.

Try a different reed in that chamber. Still issues? Then it's probably a leak.
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #4 on: August 15, 2024, 05:19:32 PM »

The C was finicky but it worked far better than the F# does.
There's no leaks at the reeds or blocks either.
After adjusting the chamber size I actually get an F# out of the reed now, though the set needs a bit more fussing to get it perfect.

I'll check the plate in another chamber and see what I can get. The reeds worked just fine out of the box so it is a bit frustrating to see it simply just not function like the others, but the reed block chamber sizes are all the same depth and are not tapered in volume, they are just routed to match the size of the reed but that's it, which is why I suspect a lack of chamber balance, and it seems to explain why the highest note doesn't work particularly well. Indeed, it's the highest three on the push that seem to be weakest, and that does make me question the chamber sizing quite a bit
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #5 on: August 16, 2024, 02:06:55 AM »

Ross, take a look at this photo; you will see that inserts have been glued into the highest reed chambers, reducing their capacity. This appears to be a standard Hohner reedblock ex-factory, though not an unknown technique used by other makers too. I reckon it will be the answer to your problem. Hope it helps....

(Edited to add that the photo came from a post by Theo on concertina.net; I trust that Theo nor concertina.net will have any objection to it being posted here).
« Last Edit: August 16, 2024, 02:10:45 AM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #6 on: August 16, 2024, 05:47:20 PM »

I'd already reduced the chamber size prior to my last comment using small strips of wood, affixed with reed wax to test the affect and it did seem to improve performance for the F# as it actually works now. The gap needs adjustment though I think, as it's still pretty quiet and needs a lot of pressure to start.

The three highest reeds all seem to have a fairly weak attack at low pressure on the push. All of the pulls however work great. I assume this is an issue with chamber size across the board, given that the push and pull, with similar tongue set heights, are remarkably different in clarity and attack.

Regarding the pin hole, I tried that first with the highest reed but didn't really get anything from it. Tried flipping the reed as well, but still nothing. It was only when I shrunk the chamber size that it started to finally work, and now I'm wondering if I should continue to make the chamber as small as is functionally possible, or if there is a potential negative outcome with that approach.

There isnt a whole lot about the subject of chamber size that I can find readily online. Is it just one of those things that people who know, know, and that everyone else just needs to wing it and see?
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #7 on: August 16, 2024, 06:04:32 PM »

Flip the plate. If push-pull response changes, it's the gap/chamber. If pull still works better, it's something else.


Chamber size is dead easy. Just design the instrument to have as big a chamber as practically possible.  :P

For every note there seem to be wolf note spots (exceptional response, even on a poorly gapped reed; very loud volume) and dead spots (essentially, anti-wolf notes) where a reed might start poorly & sound choked, or not start at all, no matter how hard you squeeze.
As you gradually increase/decrease the chamber volume, you move from wolf to dead to wolf to dead. The bigger the original size, the more change is required to shift the reed response.
I failed to find any calculatable logic in how to size the chambers for each pitch, so for a scratch build my approach is to go as big as practical, then reduce if necessary.
Overall, reed response tends to improve as the chambers get bigger (I've tested up to 5-6x times compared to a typical Italian CBA, over 4 octaves. For highest octave test was closer to 10-15x times bigger).

Since your chamber has already been designed for you by the factory, evidently, with great skill and care, you can only reduce the size. For piccolos you don't need to worry about valves clipping anything, so just keep on truckin' until the chamber is small enough.

Disclaimer: I have not done any tests on chamber shape, only tested the volume. There might be more variables at work here, but for all practical purposes, the approach is to wing it and fix wolves and deads later on if required.
« Last Edit: August 16, 2024, 06:14:48 PM by mChavez »
Logged

mChavez

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 713
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #8 on: August 16, 2024, 06:10:16 PM »

Another bright thought: if it's the reed, check that the gap near the rivet end is squeaky clean on both sides of the tongue. A tiny drop of wax or dirt in that area can derail reed performance.
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: High F# push reed difficulty sounding- voicing issue?
« Reply #9 on: August 16, 2024, 06:35:59 PM »

Thanks for the reply!
First I should clarify a bit better. This accordion was a one off box, one of a kind small melodeon. I posted about to in the makes and models thread a couple months ago. It plays mostly brilliantly but there are some flaws. The reed block looks like this (attached below). Each chamber is the size of the reed in perimeter, but not depth. The depth was all the same, save for the highest two reed positions which are still just as deep as the others but have a ramp of wood added to decrease the size a little but not dramatically. I think is likely a design flaw. My other accordions have much smaller chamber depth for comparable reed positions than this one does. The original C reeds in there pretty good playing but had similar issues. The highest reed push was a bit of a pain to get working but I did get it set perfectly eventually and it functioned well enough but not brilliantly.

So when I swapped the reeds out for D, the reed plates being a different make (harmonikas) the plate lengths actually were the same as the Hohner T reeds that were there before.
Most of it was plug and play, response similar, save for the highest reed plate which worked even less than the C set.

After resizing I got that F# push to work, though not to the standard id like for playing.

I did try flipping the plate and it seems that it's still a problem on the push. So does that mean it's a chamber issue?


free photo host
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal