Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Complications in reed response continued  (Read 1184 times)

0 Members and 1 Guest are viewing this topic.

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Complications in reed response continued
« on: August 17, 2024, 03:51:44 PM »

Alrighty, so in my other thread I mentioned I was getting no response from the highest push reed in this box I have, and through  experimentation and deduction (and from suggestions from forum members) I learned that the size of the reed chambers in the block were not sized appropriately for each reed. I shrunk the chamber dimensions for the 3 highest reeds and now they mostly work great. The two highest are perfect, albeit I hear an odd harmonic secondary sound on the highest, which sounds like both reeds activating but that's a problem for another day.

Now my last issue is the pesky A/G reed. It works, but it always is a bit weak. The push especially. So I tuned the chamber size on that one too and it got only a bit better. Tried the reed set and still, a problem. It's slowish to start and once it does you have to apply consistent firm pressure to get it to stay active. The height doesn't really seem to matter much. It feels like the reed isn't getting enough air to it. It's more muted than it's counterparts. The F#/E (lower) is also slightly muted but it behaves a bit better than the A/G, which is why I suspect the aperture size

So I looked at the chamber holes that lead to the pallets. The maker of this box made this hole in the block a small circle, whereas the highest two are squares. So I looked at the sound board and noticed the the F#/E and A/G reed positions there are squares too. Maybe he got lazy and didn't feel like routing the block out more or maybe this was prudent?

In any case, would matching the board to the block help this reed function better? I have the equipment to do this. I suspect the mismatch could influence the way air moves in and out of that chamber as well.

The slide he has installed for switching between two voices or one is pretty simple and also has squares in those positions so I wouldn't need to alter that either, just the block I imagine.

I'll attach a photo below.
Thanks!



Chart for position reference

« Last Edit: August 17, 2024, 04:14:55 PM by Ross Dubois »
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Complications in reed response continued
« Reply #1 on: August 18, 2024, 05:21:44 AM »

Quick little update. I didn't modify the holes in the reed block yet, id not do so unless forum members had info on the subject before I mutilate something potentially unnecessarily. Instead, I decided to turn the reed around so the tongues are facing the opposite direction, like the two highest reeds. That actually seems to have improved response a bit on that one too. Is it atypical to have 3 of the higher reeds on a D box flipped? I haven't seen such a thing myself, but again, this box is also an anomaly

Here's another update. When I push on the High D, it sounds as though it's activating the high F# next to it when I apply ok pressure. I'm not sure how that's happening. The pallet is closed, they don't have any gaps or leaks leading into the next reeds chamber. It sounds as though it's resonating the reed next door and getting it to speak. Any clue on how I can stop that from occuring?

Thanks to all you fine folks for fielding all my questions. I am deeply fascinated by the workings of accordions and concertinas and have been for years, but im putting in a more concerted effort in learning how to tend to my reed issues so I appreciate anyone who reads all this and responds.
« Last Edit: August 18, 2024, 06:30:46 AM by Ross Dubois »
Logged

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Complications in reed response continued
« Reply #2 on: August 18, 2024, 09:35:01 AM »

The response of high tones is always influenced by the chamber's resonance. It is a misconception that the airflow must be as even as possible. In fact, certain turbulences can even improve the responsiveness. It is difficult to describe the resonance characteristics of high tones, but certain dimensions and relationships can be verified through testing. A useful comparison can be made with a Helmholtz resonator, which consists of a cavity, neck, and mouth opening. For high tones, a small cavity and a short neck should be aimed for. Shifting the narrowest point of the neck inward also increases the resonance frequency. Therefore, it may be advantageous to widen the openings under the pallet while keeping the opening at the reed block narrower. Whether the shape is round or square has little impact, except that it changes the cross-sectional area. However, one must never forget that the reed itself must always be optimally adjusted. Often, an improvement can be achieved if the reed is slightly bent inward, with only the freely movable end maintaining the necessary clearance.
Logged

Ross Dubois

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 144
Re: Complications in reed response continued
« Reply #3 on: August 19, 2024, 04:26:22 PM »

Fascinating, thank you for the information. I make instruments for a living that operate much like Helmholtz resonators (though, the jury is still not 100% that they truly are), and it would not have crossed my mind that reeds and their chambers could fall under the same principles, but since you explained, it makes perfect sense.
The Venturi effect may also be applied here, as the opening from the pallets to the reed block undoubtedly has an impact in reed response and tuning. The 'neck' length of that wood thickness being shallower for the highs would make sense, though I couldn't modify this particular instrument to function that way unless I rebuilt the reed block.
I had to modify the highest 3 reed chambers by creating inserts to decrease the chambers sizes proportionately, and I opted to do with smooth transitions from end to end so that there are not blocky abrupt shapes in the chamber. I don't know if sharp, 90 degree angled edges of the inserts inside a chamber would cause turbulence in a negative way or not but if it does it would be hard to test properly I think unless it was blatantly obvious.

On the subject of turbulence improving responsiveness, that comes into effect with my instruments as well. Adding turbulence to the air stream can actually, if done properly, improve the clarity and response of the higher notes of the instrument. Much like how scoring is used in the windway of an organ pipe.

I find it it very interesting that these same principles can be applied to free reed instruments as well and I'll definitely be contemplating the similarities far more now.

I managed to dial in the chambers enough to make the entirety of the higher end of the accordion function well. I think the next part is just getting the set perfect on the highest F#, but otherwise it's playing significantly better than before. I do wonder if the hole shape of the reed block opening not matching the sound board opening is having a negative impact on response still, but it's currently decent enough with the chamber reshaping that I can ignore it much easier than before
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal